Makita HP2041 инструкция обслуживания

INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. Hammer Drill 20 mm (3/4”) MODEL HP2040 20 mm (3/4”) MODEL HP2041 002401 DOUBLE INSULA TION[...]

2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA002-2 (F or All T ools ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic shoc k, fire and/or s[...]

3 still does not fit, contact a qualified elec- trician to install a polarized outlet. Do not change the plug in any wa y . Double insula- tion eliminates the need for the three wire grounded pow er cord and grounded power supply system. 5. A void body contact with gr ounded sur- faces such as pipes, radiators, ranges and refrigerators. There is an[...]

4 22. Use only accessories that are recom- mended by the manufacturer f or your model. Accessories that may be suitab le for one tool, may become hazardous when used on another tool. SER VICE 23. T ool ser vice mu st be performed only by qualified repair personnel. Service or main- tenance performed by unqualified personnel could result in a risk o[...]

5 5. Do not leave the tool running. Operate the tool only when hand-held. 6. Do not touch the bit or the w orkpiece immediately after operation; the y may be extremely hot and could b urn your skin. 7. Some material contains chemicals whic h may be to xic. T ake caution to prevent working dust inhalation and skin contact. Follow material supplier s[...]

6 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Switch action CA UTION: • Bef ore plugging in the tool, always chec k to see that the s witch tr igger actuates properly and retur ns to the “ OFF ” position when released. • Switch can be lo[...]

7 Speed change T wo speed ranges can be preselected with the speed change le ver . T o change the speed, tur n the speed change le ver to the position 1 fo r low speed or the position 2 for high speed. If the speed change le ver does not turn easily , tur n the chuck slightly in either direction and turn the lev er again. Be sure that the speed cha[...]

8 ASSEMBL Y CA UTION: • Alwa ys be sure that the tool is switched off and unplugged befo re carr ying out any work on the tool. Installing side grip (auxiliary handle) Alwa ys use the side grip to ensure operating safe ty . Install the side grip so that the teeth on the grip fit in between the protrusions on the tool barrel. Then tighten the grip[...]

9 Depth gauge The depth gauge is conv enient for drilling holes of unif or m depth. Loosen the side grip and inser t the depth gauge into the hole in the side grip . Adjust the depth gauge to the desired depth and tighten the side grip . NO TE: • The depth gauge cannot be used at the position where the depth gauge strikes against the tool body . [...]

10 Blow-out b ulb (optional accessor y) After drilling the hole, use the blo w-out bulb to clean the dust out of the hole. Drilling operation CA UTION: • Pressing e xcessively on the tool will not speed up the drilling. In fact, this e xcessive pressure will only serve to damage the tip of your bit, decrease the tool perf or mance and shor ten th[...]

11 MAINTENANCE CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore attempting to perform inspection or maintenance. Cleaning vent holes The tool and its air vents ha ve to be k ept clean. Regular ly clean the tool ’ s air vents or whene v er the vents star t to become obstructed. T o maintain product SAFETY and RELIA[...]

Memo 12[...]

13 Fold Cut Stamp Timbre Makita Canada Inc. 1950 Forbes Street, Whitb y , Ontario L1N 7B7[...]

14 Y our answer s to the following questions are appreciated. Date Purchased Model No. Serial No. Initial Last Name Street Address City Province AGE: Male Female Married Single Month Day Y ear 20 Under 19 20-29 30-39 40-49 Over 50 P aste Paste P aste Paste P aste P aste Paste P aste P aste Paste P aste Paste P aste P aste P aste Paste P aste Paste [...]

15 F actory Ser vice Centres For the authorized service centre nearest you please refer to the local yellow pages directory under “ tools ” or con- tact our customer service department (Tel) 1-800-263-3734 When you need service... • Explain the problem in a letter • Enclose the letter with the tool • Package carefully and send prepaid to [...]

Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita ’ s[...]