Makita HPR2410 инструкция обслуживания

INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. Rotar y Hammer 24 mm (15/16”) MODEL HR2410 003094 DOUBLE INSULA TION[...]

2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA002-2 (F or All T ools ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic shock, fire and/or se[...]

3 Electrical Safety 4. Double insulated tools are equipped with a polarized plug (one blade is wider than the other .) This plug will fit in a polarized outlet only one wa y . If the plug does not fit fully in the outlet, re verse the plug. If it still does not fit, contact a qualified elec- trician to install a polarized outlet. Do not change the [...]

4 21. Check f or misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools operation. If damaged, have the tool ser- viced before using. Many accidents are caused by poorly maintained tools. 22. Use only accessories that are recom- mended by the manufacturer f or your model. Accessories that may b[...]

5 3. W ear a hard hat (safety helmet), safety glasses and/or face shield. Ordinary ey e or sun glasses are NO T safety glasses. It is also highly recommended that y ou wear a dust mask and thickl y padded gloves. 4. Be sure the bit is secured in place before operation. 5. Under normal operation, the tool is designed to produce vibration. The screws[...]

6 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Switch action CA UTION: • Bef ore plugging in the tool, always chec k to see that the s witch tr igger actuates properly and retur ns to the “ OFF ” position when released. T o star t the tool,[...]

7 To r q u e l i m i t e r The torque limiter will actuate when a cer tain torque lev el is reached. The motor will disengage from the output shaft. When this happens, the bit will stop turning. CA UTION: • As soon as the torque limiter actuates, s witch off the tool immediately . This will help pre vent premature wear of the tool. • Hole saws [...]

8 Installing or removing the bit Clean the bit shank and apply bit grease bef ore installing the bit. Inser t the bit into the tool. T urn the bit and push it in until it engages. If the bit cannot be pushed in, remov e the bit. Pull the chuck cov er down a couple of times. Then insert the bit again. T urn the bit and push it in until it engages. A[...]

9 Dust cup (optional accessory) Use the dust cup to pre vent dust from f alling over the tool and on yourself when perf orming overhead drilling opera- tions. Attach the dust cup to the bit as sho wn in the figure. The size of bits which the dust cup can be attached to is as fo l l ow s. OPERA TION Hammer drilling operation Set the action mode chan[...]

10 Drilling in wood or metal Use the optional drill chuck assembly . When installing it, refer to “ Installing or removing the bit ” described on the pre vious page. Set the action mode changing knob to “ rotation only ” . Y ou can drill up to 13 mm (1/2 ” ) diameter in metal and up to 32 mm (1-1/4 ” ) diameter in wood. CA UTION: • Ne[...]

11 AC C E S S O R I E S CA UTION: • These accessories or attachments are recommended for use with your Makita tool specified in this man ual. The use of any other accessories or attachments might present a risk of injur y to persons. Only use accessory or attachment f or its stated pur pose. If you need an y assistance for more details regarding [...]

Memo 12[...]

13 Fold Cut Stamp Timbre Makita Canada Inc. 1950 Forbes Street, Whitb y , Ontario L1N 7B7[...]

14 Y our answer s to the following questions are appreciated. Date Purchased Model No. Serial No. Initial Last Name Street Address City Province AGE: Male Female Married Single Month Day Y ear 20 Under 19 20-29 30-39 40-49 Over 50 P aste Paste P aste Paste P aste P aste Paste P aste P aste Paste P aste Paste P aste P aste P aste Paste P aste Paste [...]

15 F actory Ser vice Centres For the authorized service centre nearest you please refer to the local yellow pages directory under “ tools ” or con- tact our customer service department (Tel) 1-800-263-3734 When you need service... • Explain the problem in a letter • Enclose the letter with the tool • Package carefully and send prepaid to [...]

Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita ’ s[...]