Makita IMPACT DRIVER 6950 инструкция обслуживания

Impact Driver Capacities Machine screw Standard bolt Hiqh tensile bolt MODEL 6950 Equipped with Electric Brake No load speed (RPM) INSTRUCTION MANUAL 4mm ~ 8mm (5132" ~ 5116") DOUBLE INS U L AT I 0 N 0 - 2,200 6mm ~ 12" 6mm - 12" (7132" ~ 112") (7132" - 112") SPEC IF I CAT1 0 N S Impacts per minute Net weight[...]

IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. 8. 9. IO. 11. 12. 13. 2 KEEP WORK AREA CLEAN. Cluttered areas and benches invite in[...]

14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. EXTENSION CORDS. Make sure your extension cord is in good condition. When using [...]

VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user - as well as damage to the tool. If in doubt, DO NOT PLUG IN T[...]

Installing or removing the bit CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the bit. Use only the driver bit or socket bit shown at right. Do not use any other driver bit or socket bit. To install the bit, pull the sleeve in the direction of the arrow and insert the bit into the sleeve as far as[...]

CAUTION: 0 Always check the direction of rotation before operation. *Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. Operation Place the point of the driver bit in the screw head. Apply forward pressure to the tool to the extent that the bit will no[...]

MAINTENANCE CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be re[...]

ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Bits 8[...]

June-06-'95 US IMPACT DRIVER Model 6950 w Note: The switch, noise suppressor and other part configurations may differ from country to country. 9[...]

MODEL 6950 'i,'o" AtD DESCRIPTION June-06-'95 US $:D DESCRIPTION MACHINE ~ 1 2 3 4 5 6 1 8 9 10 11 12 13 14 15 16 17 19 20 21 1 1 1 1 1 4 1 1 2 1 24 1 1 1 1 1 9 1 1 1 - Ring Spring 11 Flat Washer 12 Compression Spring 13 Sleeve Hammer Case Tapping Screw BT4x20 Nylon Washer 14 Anvil Steel Ball 5 6 Hamme, Steel Ball 3 5 Flat Washe[...]

P MAKITA LIMITED ONE YEAR WARRANTY 7 . . . . . . .--. . -. . . -- I Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year perio[...]