Makita PW5001C инструкция обслуживания

INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.com Stone P olisher MODEL PW5001C 006096[...]

2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA001-3 (F or All T ools ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic shoc k, fire and/or s[...]

3 5. A void body contact with gr ounded sur- faces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. 6. Do not expose power tools to rain or wet conditions. W ater enter ing a po wer tool will increase the risk of electric shock. 7. Do not abuse the cor d. Never use the cord t[...]

4 SER VICE 23. T ool ser vice m ust be performed only by qualified repair personnel. Service or main- tenance performed by unqualified personnel could result in a risk of injur y . 24. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized par ts or f ailure to[...]

5 SPECIFIC SAFETY R ULES USB083-2 DO NO T let comf or t or familiarity with product (gained fr om repeated use) replace strict adherence to stone polisher safety rules. If y ou use this tool unsafely or incorrectl y , y ou can suffer serious personal injury . 1. Accessories must be rated f or at least the speed recommended on the tool warning label[...]

6 SA VE THESE INSTR UCTIONS W ARNING: MISUSE or failure to fo llow the safety rules stated in this instruction manual ma y cause serious personal injury . SYMBOLS USD101-2 The f ollowings show the symbols used f or tool. V ....................... volts A ....................... amperes Hz ..................... her tz ................ alternating cu[...]

7 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Ground F ault Circuit Interrupter Connect the tool to a power supply and test the Ground F ault Circuit Interrupter (GFCI) before using the tool. Push the RESET (R) button and confirm that the pilot [...]

8 Speed adjusting dial The rotating speed can be changed by turning the speed adjusting dial to a given n umber setting from 1 to 5. Higher speed is obtained when the dial is turned in the direc- tion of number 5. And low er speed is obtained when it is turned in the direction of number 1. Ref er to the below table f or the relationship between the[...]

9 Opening or closing of water le ver T o keep the le ver on the tool f or water flow open, turn it to the position A where the water passage will be ready . Retur n it to the position B to close. ASSEMBL Y CA UTION: • Alwa ys be sure that the tool is switched off and unplugged befo re carr ying out any work on the tool. Installing side grip (hand[...]

10 Installing or removing the fr ont grip CA UTION: • Make sure that the front g r ip is installed securely bef ore operation. • The front grip and the side grip cannot be installed at the same time. Remov e two screws and then the head co ver .(The front grip cannot be installed during the installation of head cover on the tool.) Install the f[...]

11 Hose connector assembly Use the hose connector assembly to connect to w ater source. It consists of the f ollowing parts. C00099 Assemble the abo ve par ts hand tight as f ollows. 1. Attach the hose connector to the outlet of water coc k. 2. Tighten the connector firmly to the hose. Inser t the con- nector to the hose connector as f ar as it wil[...]

12 MAINTENANCE CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore attempting to perform inspection or maintenance. The tool and its air vents ha ve to be k ept clean. Regular ly clean the tool ’ s air vents or whene v er the vents star t to become obstructed. Replacing dust cover brush Replace the brush on the dust [...]

13 AC C E S S O R I E S CA UTION: • These accessories or attachments are recommended for use with your Makita tool specified in this man ual. The use of any other accessories or attachments might present a risk of injur y to persons. Only use accessory or attachment f or its stated pur pose. If you need an y assistance for more details regarding [...]

Memo 14[...]

Memo 15[...]

Memo 16[...]

17 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut[...]

18 1. This product was pur chased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rade[...]

19 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CALIFORNIA 41850 Christy Street Fremont, CA 94538-5107 (510) 657-9881 14930 Northam Street La Mirada, CA 90638-5753 (714) 522-8088 4191A P ower Inn Rd. Sacramento , CA 95826 (916) 454-4768 767[...]

W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm. Some e xamples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and o[...]