Makita UNI-DRILL 6000LR инструкция обслуживания

a Machine & wood screws Bolts & Nuts, Tapper ~~~~~ Self drilling screws (steel) Uni-Drill Overall Net No load ~~~~ 1 length I weight 10 mm (3/8") MODEL 6000LR INSTRUCTION MANUAL DOUBLE INSULATION SPEC I FI CAT IO N S CaDacities * Manufacturer reserves the right to change specifications without notice. * Note: Specifications may differ [...]

IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. 8. 9. IO. 11. 12. 2 KEEP WORK AREA CLEAN. Cluttered areas and benches invite in[...]

13. DISCONNECT TOOLS. When not in use, before servicing, and when chang- ing accessories, such as blades, bits, cutters. 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger on swi[...]

ADDITIONAL SAFETY RULES 1. Always be sure you have a firm footing. 2. Hold the tool firmly. 3. Keep hands away from rotating parts. 4. When drilling into walls, floors or wherever "live" electrical wires may be encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL! Hold the tool by the insulated grasping surfaces to prevent electric shock[...]

Selecting action mode 1 For drilling, turn the change ring so that the red dot is aligned with the DRILL marking on the collar. If the change ring will not come all the way, grasp the chuck and turn the change ring again. Do not move the red dot beyond the DRILL mark- ing. For screwdriving, turn the change ring so that the red dot is aligned with t[...]

Installing or removing drill bit or driver bit CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the bit. To install the bit, place it in the chuck as far as it will go. Tighten the chuck by hand. Place the chuck key in each of the three holes and tighten clockwise. Be sure to tighten all three chuck[...]

Reversing switch action This tool has a reversing the direction of rotation. ing switch lever to the clockwise rotation or the counterclockwise. switch to change Move the revers- "F" position for "R" position for Reversing switch lever I CAUTION : 0 Always check the direction of rotation before drilling. Use the reversing switch[...]

Screwdriving operation Turn the change ring so that the red dot is aligned with the SCREW marking. Place the point of the driver bit in the screw head and apply pressure to the tool. When driving screws, start the tool slowly and then increase the speed gradually. 4.5 (1 1/64") 4.8 (3/16") 5.1 (13/64 ') 6.8 (17164") NOTE : 2.9 -[...]

ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Chuck key SI0 Part No. 763412-5 0Grip 26 Par[...]

Oec.-20-83 US 10 mm (3/8") Model 6000LR UNI-DRILL Note: The switch, noise suppressor and other part configurations may differ from country to country. 10[...]

MODEL 6000LR ITEM NO. NO. USED MACHINE ~ 1 2 3 4 5 6 1 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 1 1 1 - DESCRIPTION Apr -07-'88 US $ED DESCRIPTION MACHINE ~ Drill Chuck S10 Change Ring 0 Ring 27 Gear Housing Flat Washer 16 Spindle Compression Spring 9 Helical Gear 56 Woodruff Key 3 Gear Shaft Thrust[...]

1’ MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, retum the COMPLETE tool, fr[...]