Maytag W10562339B-SP инструкция обслуживания

1 W10562335B W10562339B-SP T able of Contents DR YER SAFETY ......................................................................... 2 INST ALLA TION REQUIREMENTS ............................................. 3 T ools and Parts ...................................................................... 3 LOCA TION REQUIREMENTS .........................[...]

2 DRYER SAFETY[...]

3 INST ALLA TION REQUIREMENTS TOOLS AND P AR TS Gather the requir ed tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. T ools needed: Parts package is located in dryer drum. Check that all parts are included. Parts needed: (Not supplied with dryer) Check local codes. Check existing e[...]

4 Check code requir ements. Some codes limit, or do not permit, installing dryer in garages, closets, mobile homes, or sleeping quarters. Contact your local building inspector . DR YER DIMENSIONS LOCA TION REQUIREMENTS Y ou will need: ■ A location allowing for proper exhaust installation. See “V enting Requirements.” ■ A separate 30 amp cir[...]

5 Spacing for recessed ar ea or closet installation All dimensions show recommended spacing allowed, with tested spacing of 0" (0 mm) clearance on sides and rear . ■ Additional spacing should be considered for ease of installation and servicing. ■ Additional clearances might be requir ed for wall, door , and oor moldings. ■ Additional[...]

6 Flange Models with riser Models without riser INST ALL LEVELING LEGS Prepar e dryer for leveling legs 1. T o avoid damaging oor , use a large at piece of cardboar d from dryer carton; place under entir e dryer . Firmly grasp dryer body (not console panel) and gently lay dryer down on cardboar d. IMPORT ANT : If laying dryer on its back, use[...]

7 ELECTRICAL CONNECTION Electrical Connection Options Power Supply Cord 1. Choose electrical connection type Power supply cord 4-wir e receptacle (NEMA T ype 14-30R): Go to Power Supply Cord Connection. 3-wire dir ect connection: Go to Direct Wir e Connection. 4-wire dir ect connection: Go to Direct Wir e Connection. Power supply cord 3-wir e recep[...]

8 B C E Connect neutral ground wir e and neutral wire 2. Connect neutral ground wir e (E) and neutral wire (white) (C) of power supply cord under center terminal block scr ew (B). Tighten screw . Connect remaining wir es 4. Connect remaining wir es to outer terminal block screws. Tighten screws. Finally , reinsert tab of terminal block cover into s[...]

9 3-wire r eceptacle (NEMA type 10-30R) 3-prong plug Spade terminals with upturned ends Ring terminals Use where local codes permit connecting cabinet-gr ound conductor to neutral wire. 3-wire Power Supply Cor d Connection 3. Connect remaining wir es Connect remaining wir es to outer terminal block screws. Tighten screws. Finally , reinsert tab of [...]

10 4. Connect ground wir e F A Connect ground wir e (green or bar e) (F) of direct wir e cable to external ground conductor screw (A). Tighten scr ew . E C B 3. Connect neutral ground wir e and neutral wire Connect neutral ground wir e (E) and place hooked end (hook facing right) of neutral wire (white or center wir e) (C) of direct wir e cable und[...]

11 Place hooked ends of remaining dir ect wire cable wir es under outer terminal block screws (hooks facing right). Squeeze hooked ends together and tighten screws. Finally , reinsert tab of terminal block cover into slot of dryer r ear panel. Secure cover with hold-down scr ew . Now , go to “V enting Requirements.” 5. Connect remaining wir es [...]

12 VENTING REQUIREMENTS VENTING WARNING: T o r educe the risk of re, this dryer MUST BE EXHAUSTED OUTDOORS. IMPORT ANT : Observe all gover ning codes and ordinances. Dryer exhaust must not be connected into any gas vent, chimney , wall, ceiling, attic, crawlspace, or a concealed space of a building. Only rigid or exible metal vent shall be us[...]

13 Louvered Hood Good Angled Hood Box Hood Better Exhaust hoods: Elbows: Recommended Styles: Recommended Styles: ■ 45° elbows provide better airow than 90° elbows. Clamps: ■ Use clamps to seal all joints. ■ Exhaust vent must not be connected or secured with scr ews or other fastening devices that extend into interior of duct and catch li[...]

14 Whirlpool V ent System Chart Number of 90° elbows T ype of vent Box/louvered hoods Angled hoods 1 4 3 2 0 Rigid metal Rigid metal Rigid metal Rigid metal Rigid metal 64 ft. (20 m) 54 ft. (16.5 m) 44 ft. (13.4 m) 35 ft. (10.7 m) 27 ft. (8.2 m) 58 ft. (17.7 m) 48 ft. (14.6 m) 38 ft. (11.6 m) 29 ft. (8.8 m) 21 ft. (6.4 m) The V ent System Charts p[...]

15 2. Connect vent to exhaust hood V ent must t over the exhaust hood. Secure vent to exhaust hood with 4" (102 mm) clamp. Run vent to dryer location using straightest path possible. Avoid 90° turns. Use clamps to seal all joints. Do not use duct tape, screws, or other fastening devices that extend into interior of vent to secure vent, bec[...]

16 T urn on cold water faucet Check that the water faucets are turned on. Check for leaks Check for leaks around “Y” connector , faucets, and hoses. 6. 7. Attach long hose to “Y” connector and tighten couplings 4. One end of the long hose has a wire mesh strainer inside the coupling. Attach this end to the “Y” connector . Attach washer [...]

17 CONNECT VENT 1. Connect vent to exhaust outlet Using a 4" (102 mm) clamp, connect vent to exhaust outlet in dryer . If connecting to existing vent, make sure vent is clean. Dryer vent must t over dryer exhaust outlet and inside exhaust hood. Check that vent is secured to exhaust hood with a 4" (102 mm) clamp. Move dryer to nal lo[...]

18 REVERSE DOOR SWING Y ou can change your door swing from a right-side opening to a left-side opening, if desired. 1. Place a towel or soft cloth on top of dryer or work space to avoid damaging the surface. Remove the door assembly 1. Open the dryer door . 2. Remove the bottom screw (B) fr om each of the two hinges that attach dryer door to front [...]

19 Reverse the strike 1. Remove the door strike from the dryer door opening. 2. Remove the cosmetic screw opposite the door strike. A B A. Door strike B. Cosmetic screw 3. Reinstall the door strike and cosmetic screw on the opposite side of dryer door opening from wher e they were r emoved. NOTE: Door strike and plugs must be on the same side of th[...]

W10562335B W10562339B-SP ®/™ © 2013. 05/13 All rights reserved. Printed in U.S.A.[...]