Memorex CH4 инструкция обслуживания

For product questions or service, CALL 1-919-550-3259 or go to www .beastpowerequipment.com  When you call the help-lin e y ou will need to have the following information: Date of Purchase: _______________________ Location of Purchase: _______________________ Serial #: _______________________ Model #: _______________________ TM This manual conta[...]

Copyright© 2009 by GXi Outdoor Powe r, LLC. All righ ts reserved. No part of this publication can be repro duced or di stributed without prior written permission of GXi Outdoor Powe r, LLC Clayton, NC 27520 USA. Brush Master™ is a trademark of GXi Outdoo r Power, LLC DEK® is registered trade mark of GXi Outdoo r Power, LLC DEK® is exclusively [...]

Heavy Duty Power Equipment Contents Warnings ............................................................................ 1 Product Specif ications ........................................................ 2 Component Ident ification ................................................... 3 Missing Parts Order Form ………………………………?[...]

Rev: 07/2010  Brush Master™ Chipper/S hredder with 2-Way Feed  1 Heavy Duty Power Equipment W arnings This symbol indicates important safe ty instructions which, if not followed, could endanger personal safe ty and/or property. Read and follo w all instructions in this manual before attempting to opera te this machine. Failure to comply w i[...]

Rev: 07/2010  Brush Master™ Chipper/S hredder with 2-Way Feed  2 Heavy Duty Power Equipment Training 1. Read, understand, and follow all instru ctions o n the machine and in the manual) before attempting to assemble and operate. Keep this manual in a safe place for future and regular reference an d for ordering replacem ent pa rts. 2. Be fa[...]

Rev: 07/2010  Brush Master™ Chipper/S hredder with 2-Way Feed  3 Heavy Duty Power Equipment Component Identification Recoil Starter The starter handle is located on the engine. Pull the starter handle to start engine. Chipper Funnel Use the chipper funnel to feed leaves only. Chipper Chute Use the chipper chute to feed longer and/or thicker[...]

Rev: 07/2010  Brush Master™ Chipper/S hredder with 2-Way Feed  4 Heavy Duty Power Equipment Missing Parts Request Form Name Phone Email Address IMPORT ANT : Please include y our r eceipt. Without a receipt, y our order will be delayed. Y ou may also email us at: customerservice@gxioutd oorpower .com. If emailing, please scan in your proof o[...]

Rev: 07/2010  Brush Master™ Chipper/S hredder with 2-Way Feed  5 Heavy Duty Power Equipment Safety Information Preparation 1. Thoroughly inspect the area where the chipper/ shredder is to be used. Remove all rocks, bottles, cans, or other foreign objects which could be picke d up or thrown and cause perso nal injury or damage to the machine[...]

Rev: 07/2010  Brush Master™ Chipper/S hredder with 2-Way Feed  6 Heavy Duty Power Equipment 8. Never attempt to unclog either the feed i ntake o r discharge opening while th e engine is running. Shut the engine off, wait until all moving parts have stopped, disconnect the spar k plug wi re and ground it against the engine before clearing d [...]

Rev: 07/2010  Brush Master™ Chipper/S hredder with 2-Way Feed  7 Heavy Duty Power Equipment Assembly Required tools: A Philips head screw driver Approximate assembly time: 10 minutes 1. Remove the chipper from its carton. Remove staples, break glu e on top flaps, or cut tape at carton end and peel along top flap to ope n carto n. 2. Verify [...]

Rev: 07/2010  Brush Master™ Chipper/S hredder with 2-Way Feed  8 Heavy Duty Power Equipment NOTE: The chipper/shredder operates most efficiently at the factory set engine speed of 3600 RPM. The speed is controlled by the governor, and the throttle setting should not be adjusted. Do not attempt to adjust the speed of the engine. Emission Con[...]

Rev: 07/2010  Brush Master™ Chipper/S hredder with 2-Way Feed  9 Heavy Duty Power Equipment steps until engine fires. Rapid retraction of the recoil starter c ord can pull the starter cord back faster than you can let go. When starting the engine, pull the cord slowly until resistance is felt then pull rapidly to avoid kickbac k. NOTE: A no[...]

Rev: 07/2010  Brush Master™ Chipper/S hredder with 2-Way Feed  10 Heavy Duty Power Equipment Maintenance and Storage Item Before each use 20 hrs or every 3 months 50 hrs or every 3 months 100 hrs or every 6 months 300 hrs or every 1 year Engine Oil (Check) X Engine Oil (Change) X Air Cleaner (Check) X Air Cleaner Wash X Fuel filter Cup (Cle[...]

Rev: 07/2010  Brush Master™ Chipper/S hredder with 2-Way Feed  11 Heavy Duty Power Equipment Always stop engine, disconnect spark plug, and ground against engine before cleaning, lubricating or doing any kind of maintenance on your machine. Removing and Shar pening the Bl ade The chipper wa s shi pped with one blade attached an d one blade [...]

Rev: 07/2010  Brush Master™ Chipper/S hredder with 2-Way Feed  12 Heavy Duty Power Equipment T roubleshooting Problem Cause Remedy Engine fails to start 1. Spark plug wire disconnect ed. 2. Fuel tank empty or stale fuel. 3. Throttle control lever not in correct starting position. (If equipped) 4. Choke not in CHOKE position. (If equipped) 5[...]

Rev: 04/2010  Brush Master™ Chipper/S hredder with 2-Way Feed  13 Heavy Duty Power Equipment Limited W arranty & Service Products Covered by this Warranty Length of Warranty : *(from the date of original retail purchase) Noncommercial /Nonrental Commercial Rental Engine 12 months 12 months 12 months * Length of Warranty: Consumable part[...]

Turf Beast Brush Master Brush Beast The Beast Check out our other great products at www .HomeDepot.com or visit our web site at www .beastpowerequipment.com Turf Beast 36 in. Walk Behind Mower Turf Beast 54 in. Walk Behind Mower The Beast 100 in. Tow Behind Mower Brush Beast 36 in Brush Mower.[...]