Memorex MT1091 инструкция обслуживания

MT1091 9” Color Television Owner’s Manual Multi Function Remote On Screen Display VOLUME CHANNEL POWER R As an E NERGY S TAR ® Partner, MEMCORP has determined that this product meets the E NERGY S TAR ® guidelines for energy efficiency.[...]

– 1 – BEFORE YOU OPERATE YOUR NEW TELEVISION To get the most from your new color television, read and follow this Owner’s Manual carefully. INSTALLATION GUIDELINES • Place your TV in a room with adequate ventilation. • Keep your TV set away from sources of direct heat, such as heat registers or direct sunlight. • Do not place your TV on[...]

– 2 – FEATURES • On-screen graphics guide you through setup features and operations • Automatic programming of channels allows easy selection of stations available in your viewing area • Sleep timer programs the TV to turn itself off at a preset time • One day timer programs the TV to come on once at a preset time • Weekly timer progr[...]

– 3 – LOCATION OF CONTROLS IN VIDEO EXT.ANT. UHF/VHF AUDIO DC−12V Multi Function Remote On Screen Display VOLUME CHANNEL POWER R 7 6 5432 1 @!0 9 8 7 EARPHONE JACK ( ) 8 ANTENNA HOLDER 9 AUDIO IN (put) JACK 10 VIDEO IN (put) JACK 11 DC INPUT JACK 12 VHF/UHF EXT. ANT. JACK 1 POWER SWITCH 2 CHANNEL ▲ (UP) BUTTON 3 CHANNEL ▼ (DOWN) BUT[...]

– 4 – The REMOTE CONTROL unit requires two 1.5 volt “ AA ” size batteries. The BATTERY COMPARTMENT is located on the back of the unit. To open, press down of the lid and slide toward the bottom of the unit. Install the batteries exactly as shown by the diagram in the compartment. NOTE: If one or both of the batteries are reversed, the REMOT[...]

– 5 – CHANNEL VOLUME MUTE MENU RECALL SLEEP TV/VIDEO POWER Q.REV. Remote Control Number Buttons Press to select a channel. For channels 1-9, press 0, then the channel you want to watch. For example, for channel 6, press 0, 6. For channels 100-125, press the 100 button, then press the last two digits of the channel you want to watch .For example[...]

– 6 – ANTENNA CONNECTIONS If you are using an indoor antenna (included) or an outdoor antenna (not included) follow the instructions below that correspond to your antenna system. If you are using a cable television service (CATV), refer to CATV connections. Combination VHF/UHF Antenna (Single 75 ohm cable or 300 ohm twin-lead wire) Connect the [...]

– 7 – A — Allows viewing of scrambled channels through converter/descrambler box. B — Allows full use of TV tuner and Remote Control. NOTE: For other cable connections, consult your cable company. Some cable companies offer “ premium pay ” channels in which the signal is scrambled. Descrambling these signals for normal viewing requires [...]

– 8 – You can connect the TV to a household outlet or to the cigarette lighter of your car. AC Power Connect the polarized AC cord plug to a 120V AC 60Hz household outlet. NOTES 1. NEVER CONNECT THE AC LINE CORD PLUG TO OTHER THAN THE SPECIFIED VOLTAGE. USE THE ATTACHED POWER CORD ONLY. 2. IF THE POLARIZED AC CORD DOES NOT FIT INTO A NON-POLARI[...]

– 9 – SELECTING A LANGUAGE QUICK USE GUIDE If you ’ re already familiar with TV hookup and operation, just follow the quick steps below to make some basic connections and adjustments before using your new TV. a Place batteries in the remote control. (See page 4). s Connect the TV to an antenna or cable. (See page 6). d Connect a power supply.[...]

– 10 – SETTING THE CLOCK a Press the MENU button twice to bring up the menu screen and select CLOCK SET. CLOCK SET SUN – – : – – AM EXIT [MENU] : MOVE [+] / [ – ] : ADJUST s Use the + or – button to select the cor- rect day of the week. CLOCK SET TUE – – : – – AM EXIT [MENU] : MOVE [+] / [ – ] : ADJUST d Press the MENU but[...]

– 11 – PROGRAMMING CHANNELS With automatic programming, the TV automatically places every channel you receive in its memory, allowing you to scan through those channels when you press the CHANNEL (Up/Down) buttons. With manual programming, you tell the TV what channels you want to scan through when you press the CHANNEL (Up/Down) buttons. Autom[...]

– 12 – ADDING/DELETING CHANNELS Manual Programming a Press the MENU button to bring up the menu screen. MENU TUE 1:35PM CLOCK SET PROGRAM TIMER PICTURE ADJUST CH PROGRAM LANGUAGE DEMONSTRATION EXIT [+] / [ – ] : MENU SELECT [MENU] : ENTER s Use the + or – button to highlight CH PROGRAM, then press the MENU but- ton to select it. CH PROGRAM [...]

– 13 – SETTING THE TIMERS You can program your TV to turn on a specific channel at a preset time once (one day timer) or at the same time every day or every week (weekly timer). You also can program your TV to turn itself off after a specified amount of time (sleep timer). One Day Timer a Press the MENU button to bring up the menu screen. MENU [...]

– 14 – Weekly Timer a Press the MENU button to bring up the menu screen. MENU TUE 1:35PM CLOCK SET PROGRAM TIMER PICTURE ADJUST CH PROGRAM LANGUAGE DEMONSTRATION EXIT [+] / [ – ] : MENU SELECT [MENU] : ENTER s Use the + or – button to highlight PRO- GRAM TIMER, then press the MENU button. PROGRAM TIMER ONE DAY OFF WEEKLY OFF EXIT [+] / [ ?[...]

– 15 – Sleep Timer a Press the SLEEP button to bring up the sleep timer screen. SLEEP 00 s Press the SLEEP button until the desired sleep time (10, 20, 30, 40, 50, 60, 70, 80 or 90 minutes) appears on-screen. The timer will begin counting down to zero, and the on-screen display will dis- appear. When the timer reaches zero, the TV will turn its[...]

– 16 – ADJUSTING THE PICTURE a Press the MENU button to bring up the menu screen. MENU TUE 1:35PM CLOCK SET PROGRAM TIMER PICTURE ADJUST CH PROGRAM LANGUAGE DEMONSTRATION EXIT [+] / [ – ] : MENU SELECT [MENU] : ENTER s Use the + or – button to highlight PIC- TURE ADJUST, then press the MENU button. PICTURE ADJUST ADJUST RESET EXIT [+] / [ ?[...]

– 17 – USING THE AUDIO, VIDEO AND EARPHONE JACKS Audio/Video Input The AUDIO and VIDEO IN (put) jacks on the back of the TV allow you to receive au- dio (sound) and video (picture) from exter- nal sources, such as VCR, Video Disc, etc. Follow the instructions below to play video from an external source. 1 Use audio/video cables (not included) t[...]

– 18 – CABLE TV OPERATION a Press the MENU button to bring up the main menu screen. s Use the + or – button to highlight CH PROGRAM, then press the MENU button to select it. d Press the MENU button until CABLE appears to the right of AIR/CABLE. On CATV (Cable Television) systems, programs are brought into the home on VHF chan- nels 2 – 13, [...]

– 19 – PROBLEM SOLUTION • Make sure the unit is plugged in. • Unplug the unit from the electrical outlet for 60 seconds. Then plug it in and turn it on again. No Power • Make sure the antenna is properly connected at the back of the TV. • Make sure the antenna is not broken. • Adjust the brightness and contrast controls. No picture No[...]