Miele G 5225 инструкция обслуживания

Operating Instructions Dishwasher G 5220 G 5225 To prevent accidents and appliance damage read these instructions before installation or use. M.-Nr. 09 510 211 en - US, CA[...]

IMPORTANT SAFETY INSTRUCTIONS .......4 Guide to the dishwasher ............................................7 Control panel ......................................................8 Caring for the environment ..........................................9 Before using for the first time .......................................1 0 To open the door ........[...]

Interrupting a program ..............................................3 9 Changing a program ...............................................3 9 Additional options ................................................4 0 Turbo ...........................................................4 0 Delay start .......................................................[...]

WARNING – When using your dishwasher, follow basic precautions, including the following: Read the operating instructions and installation diagram carefully before installation or use of the dishwasher to prevent injury and machine damage. Use the dishwasher only for its intended purpose. This appliance is intended for residential use only. Keep t[...]

Installation ~ The dishwasher must be installed and connected in accordance with the installation instructions. ~ Installation and repair work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and may void the warranty. ~ Do not install or use a damaged dishwasher. A damaged appliance is da[...]

Use ~ To reduce the risk of injury, do not allow children to play in, on or near the dishwasher. It is possible for small fingers may be pinched in the door. ~ Only use the dishwasher if all panels are properly in place. ~ Do not tamper with the controls. ~ Do not sit or stand on the door or baskets of the dishwasher. Close the door when not in use[...]

a Upper spray arm (not visible) b Cutlery tray c Upper basket d Middle spray arm e Air inlet for drying (depending on model) f Lower spray arm g Triple filter system h Data plate i Child Safety Lock in the door handle (not visible) j Rinse aid reservoir k Dual compartment detergent dispenser l Salt container Guide to the dishwasher 7[...]

Control panel a Program selection b Time display c Program sequence indicator d Check / Refill indicators e Start/Stop button with indicator light f Delay start button with indicator light g Turbo button with indicator light h Program button i K button (On/Off) This operating instruction manual describes several dishwasher models with different ind[...]

Energy saving washing This dishwasher is economical in the use of water and electricity. For best results follow these tips: ^ For lowest energy consumption you may connect the dishwasher to a cold water source. ^ For fastest possible wash times, with slightly higher energy consumption, connect the dishwasher to a hot water source. ^ Make full use [...]

To open the door ^ Reach under the handle and pull the door open. If the door is opened during operation the dishwasher will stop running. Once the door is closed the program will restart. To close the door ^ Push the baskets in. ^ Lift the door and push until it clicks into place. Child safety lock Te child Safety Lock is designed to prevent child[...]

Water softener To achieve good cleaning results, the dishwasher needs soft water (water that is low in minerals). Hard water results in calcium deposits on dishware and in the dishwasher. If your tap water hardness is above 4 °d (4 gr/gal) the water should be softened. The built-in water softener is designed for this purpose. The water softener is[...]

Programming the water softener To exit the programming mode at any time turn the dishwasher off with the K button. ^ Press the K button to turn the dishwasher off. ^ Press and hold the "Start / Stop" button and turn the dishwasher on simultaneously using the K button. Keep the "Start / Stop" button pressed for at least four seco[...]

Checking the programmed water hardness ^ Press the K button to turn the dishwasher off. ^ Press and hold the "Start/Stop" button and turn the dishwasher on simultaneously using the K button. Keep the "Start/Stop" button pressed for at least four seconds until the "Start/Stop" indicator light comes on. ^ Press the "[...]

Every dishwasher is tested before leaving the factory. Any water remaining in the machine is from the final factory test and does not indicate that the machine has been used. Filling the salt container , Inadvertently filling the salt container with dishwashing detergent (including liquid detergent) will damage the water softener. , Only use water [...]

Refill salt message ^ When the "Salt" indicator light comes on, refill the salt after the program has finished. After the container has been filled, the "Salt" indicator light can remain on for a short time. It will go out once the reactivation process is complete. The "Salt" indicator light is turned off if you have p[...]

Deactivate indicators If you only ever use "Tab" detergent products in your dishwasher, you can switch both messages off if you wish. ^ Turn the dishwasher off with the K button. ^ Press and hold the "Start/Stop" button and turn the dishwasher on simultaneously using the K button. Keep the "Start/Stop" button pressed f[...]

Rinse aid Rinse aid is needed to prevent spotting on dishes and glassware. The rinse aid is filled in the reservoir and the set amount will be automatically dosed. , Filling the rinse aid reservoir with detergent will damage the reservoir. Only pour rinse aid formulated for residential dishwashers into the reservoir. When using "Tab" dete[...]

Rinse aid indicator When the Rinse aid indicator first comes on, there will be enough rinse aid left fo r2-3 washes. ^ The rinse aid indicator on the control panel will light when the rinse aid reservoir needs refilling. If you only ever use "Tab" detergent products in your dishwasher, you can switch the reminders for salt and rinse aid o[...]

Adjusting the dosage In order to obtain an optimal cleaning result you can adjust the dosing quantity of the rinse aid. The dosage selector is preset to 3. This dispenses approximately 3 ml of rinse aid per program. It can be adjusted f r o m0t o6 . – Use a higher setting if spots appear on dry glassware. ^ Use a lower setting if streaking appear[...]

, Do not wash items soiled with ash, sand, wax, grease or paint in the dishwasher. Ash and sand do not dissolve and will be distributed throughout the inside of the dishwasher. Wax, grease and paint will cause permanent discoloration and damage to the dishwasher. ^ Scrape food from dishes before placing them in the dishwasher, rinsing is not necess[...]

Items not recommended for dishwashing – Cutlery with wooden handles – Wooden cutting boards – Glued items such as old knives with handles glued together around the shank of the blade – Handmade craft items, antique, metal trimmed or decorative glassware – Plastic items that are not heat resistant – Copper, brass, tin or aluminum – Dis[...]

Typical load for 10 place settings with cutlery tray Upper basket Lower basket Cutlery tray Loading the dishwasher 22[...]

Typical load for 16 place settings with cutlery tray Upper basket Lower basket Cutlery tray Loading the dishwasher 23[...]

Typical load for 10 place settings with cutlery basket Upper basket Lower basket Cutlery basket Loading the dishwasher 24[...]

Typical load for 13 place settings with cutlery basket Upper basket Lower basket Cutlery basket Loading the dishwasher 25[...]

Upper basket , Always use the dishwasher with the upper and lower basket in place. ^ Load the upper basket with small, lightweight, or delicate items such as cups, saucers, glasses, dessert bowls and flat pans. Long items such as soup ladles, mixing spoons and long knives should be placed lying down across the front of the upper basket. Adjustable [...]

Adjusting the upper basket In order to gain more space for taller items the upper basket can be adjusted on three levels with 2 cm between each level. The upper basket can also be set at an angle with one side high and the other side low. Make sure, however, that the basket can slide smoothly in and out of the cabinet. ^ Slide out the upper basket.[...]

Lower basket ^ Place larger and heavier items such as plates, serving platters, saucepans, bowls, etc. in the lower basket. It can also be used for glasses, cups, small plates and saucers. Dishwasher with cutlery tray Dishwasher with cutlery basket Heavily soiled items ^ Place very large plates in the center of the lower basket. When tilted, plates[...]

MultiComfort zone The rear section of the lower basket is used for cups, glasses, plates, pots and pans. ^ The glass rack can be folded up to make more room for tall items. ^ Stemware, e.g. wine, champagne and beer glasses, can be leaned against the glass rack or suspended from it. The height of the glass rack is adjustable. ^ Slide the glass rack [...]

Cutlery tray (depending on model) ^ Arrange the cutlery as shown in the cutlery tray. For easier unloading cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc. Place knives with the cutting edge down and forks with the prongs between the holders. Spoons should be placed in the opposite direction with the handles b[...]

Cutlery basket (depending on model) The cutlery basket can be placed anywhere on the front rows of spikes in the lower basket. ^ To avoid risk of injury, knives and forks should be placed with the handles upwards in the basket. However, cutlery placed handle down in the basket will come out cleaner and drier. ^ Place small items of cutlery in the i[...]

Optional dishwasher accessories are available from your Miele dealer, Miele or Mieleusa.com (depending on your model some may already be supplied with your machine as standard). If you would like to... the following accessory will need to be ordered... ...wash a Miele Cappuccinatore ... a Cappuccinatore insert for the upper basket. ...wash addition[...]

Detergent , Dishwasher detergents contain irritant and corrosive ingredients. Avoid inhaling or swallowing dishwasher detergent. Keep children away from detergent. Keep detergent out of the reach of children. Keep children away from the dishwasher when the door is open. There could still be detergent residues in the dishwasher. Only add detergent j[...]

Adding detergent ^ Press the latch on the detergent dispenser. The flap will spring open. The flap is always open at the end of a program. ^ Add detergent to the compartments and close the container flap. ^ Use one tab or add powder or gel detergent to compartment II and close the flap. ^ If a Pre-rinse is desired, and available for your chosen pro[...]

Turning the dishwasher on ^ Make sure the spray arms can rotate freely. ^ Close the door. ^ Open the water supply if it is closed. ^ Press the K button to turn the dishwasher on. The Start/Stop indicator flashes, and the indicator for the last selected program comes on. Selecting a program Choose the program according to the type of dishware and so[...]

Program guide When to use Program sequence Pre-rinse Main wash Interim rinse Final rinse Drying 12 1 2 Pots & Pans For normally soiled pots & pans with dried on food , and heavily soiled dishware, use 120% detergent recommended. XX X X X Normal Program for completely washing a full load of normally soiled dishware with the ability to adjust[...]

Time display Before the program starts, the time display shows the time of the selected program in hours and minutes. The remaining time is displayed during the program. The time that is displayed may vary for the same program. It depends on the temperature of the incoming water, the reactivation cycle, the type of detergent and the quantity and so[...]

Program sequence indicator After a program has started, the program sequence indicator displays the respective program step. At the end of a program The program has ended when a 0 appears in the time display and "End" lights up in the program sequence display. If the Express program was selected, the drying fan will run for a few minutes [...]

Interrupting a program A program will be interrupted as soon as the door is opened. When the door is closed again, the program will continue from where it was interrupted. , Water in the dishwasher is hot. Risk of scalding! Only open the door if absolutely necessary and be very careful. Before closing the door again, leave it slightly ajar for appr[...]

Turbo The "Turbo" function can be used to reduce the program run-times, in programs in which the option is available. Energy consumption will increase to achieve optimum results. ^ Press the K button to turn the dishwasher on. The Start/Stop indicator light flashes. ^ Select the desired program. ^ Press the Turbo button. The Turbo indicat[...]

Delay start The start time of a program can be delayed. The start time can be delayed from 30 minutes to 24 hours. The delay is set in 30 minute increments. For a delay start time between 30 minutes and 9 hours 30 minutes, the delay is set in 30 minute increments. For a delay start time of 10 hours or more, the delay is set in increments of one hou[...]

The time will count down to the program start: for more than 10 hours in 1 hour increments, for less than 10 hours in 1 minute increments. When the set time is reached, the selected program will start automatically. The remaining time is shown in the time display, the Delay start indicator light goes out and the Start/Stop indicator light comes on.[...]

Optimize Standby A few minutes after the last button is pressed or a few minutes after the end of the program the dishwasher will switch to Standby mode to save energy. The time display and the indicator lights are turned off and only the Start/Stop indicator light flashes slowly. If the dishwasher is not turned off or opened after the program ends[...]

Factory defaults If you have changed any settings, you can reset them to the factory defaults. ^ Press the K button to turn the dishwasher off. ^ Press and hold the Start/Stop button and simultaneously turn the dishwasher on using the K button. Keep the Start/Stop button pressed for at least four seconds until the "Start/Stop" indicator l[...]

, Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage. Technical faults Problem Possible fault Solution After turning on the dishwasher with the K button, the Start/Stop indicator light does not flash. The di[...]

Faults in the water intake or water drain Problem Possible fault Solution The Intake/Drain indicator light alternates between flashing and remaining steady. The water supply is closed. Open the water supply all the way. The dishwasher stops running. The Intake/Drain indicator light flashes. The time display shows fault FXX. Before fixing the fault:[...]

General problems with the dishwasher Problem Possible fault Solution The time display is dark. Only the Start/Stop indicator light flashes slowly. The dishwasher has gone into Standby mode to save energy. Press any button to come out of Standby. There are detergent residues in the dispenser at the end of a program. The dispenser was wet when deterg[...]

Sounds Problem Possible fault Solution There is a knocking noise in the wash cabinet The spray arm is hitting an item in the basket. Interrupt the program, rearrange items blocking the spray arms. There is a rattling noise in the wash cabinet Items are not secure in the wash cabinet. Interrupt the program, and rearrange loose pieces. A foreign obje[...]

Poor cleaning results Problem Possible fault Solution The dishes are not clean. The dishes were not loaded correctly. See "Loading the dishwasher". The program was not powerful enough. Select a more intensive program (see "Program Guide"). Not enough detergent was dispensed. Use more detergent, or change the detergent. The spray[...]

Problem Possible fault Solution Dishes are not dry, glasses and cutlery are spotted. The rinse aid setting may be too low, or the rinse aid reservoir is empty. Increase the dosage, refill the reservoir or switch the rinse aid product when refilling (see "Rinse aid"). Dishes were taken out too soon. Leave dishes in longer (see "Use&qu[...]

Problem Possible fault Solution Glasses have a brown or blue discoloration; film cannot be wiped off. Detergent deposits. Change detergent right away. Glasses are dull and discolored; film cannot be wiped off. Glasses are not dishwasher safe. The surface is affected. There is no remedy. Only use dishwasher safe glasses. Tea or lipstick stains have [...]

Repairs In the event of a fault which you cannot correct yourself please contact the Miele Service Department at the phone number on the back of this booklet. ^ Please quote the model type and number of your appliance. These can be found on the data plate along the right edge of the door. PC Update The Program Correction (PC) allows a technician to[...]

User Maintenance Instructions To prevent accidents and machine damage, read these instructions before installation or use.[...]

Check and clean your dishwasher regularly. This will help avoid problems and faults. , Abrasive cleaning agents, all-purpose cleaners, thinner or ammonia based cleaners should not be used on the dishwasher. They will damage the surface. Wash cabinet Generally, the wash cabinet is self cleaning if the correct amount of detergent is used. The wash ca[...]

Triple filter system The triple filter system in the base of the wash cabinet prevents food from being redeposited on dishes. It also protects the circulation pump from damage caused by foreign objects (e.g. broken glass, bones). During normal use, the filter system is self-cleaning. , The machine must not be used without all the filters in place! [...]

To clean the inside of the filter, the flap must be opened. ^ Push the clips together a and open the flap b . ^ Rinse under running water. ^ Close the flap so that the clip engages. ^ Return the filter so it lies flat in the base of the wash cabinet. ^ Lock the filter by turning the handle clockwise. , The triple filter system must be inserted and [...]

Cleaning the spray arms Sometimes particles of food get stuck in the spray arm jets. The spray arms should be inspected and cleaned every 4 - 6 months. ^ Turn off the dishwasher before cleaning. Removing the spray arms ^ Remove the cutlery tray (if present). ^ Push the upper spray arm up to engage the inner ratchet and unscrew the spray arm. ^ Lift[...]

Cleaning the drain pump and non-return valve If the dishwasher is not completely drained at the end of a program, the drain pump or non-return valve may be blocked. ^ Turn off the dishwasher and pull the plug. ^ Remove the triple filter (see "Triple filter system"). ^ Use a cup or bowl to scoop water out of the wash cabinet. ^ Tilt the lo[...]

Installation Instructions Please refer to the Installation Diagram supplied with these instructions. Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information.[...]

, Installation, repairs and other work by unqualified persons could be dangerous. Check that the voltage, frequency and fuse rating shown on the data plate match the household mains supply. The power outlet must be accessible after installation. Do not use an extension cord to connect the dishwasher to the mains. Danger of overheating! See data pla[...]

Hardwired electrical connection It is possible to hardwire this appliance to an existing power cable. , CAUTION: Before servicing, disconnect the power supply by either removing the fuse, shutting off the power main or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician[...]

Connection to the water supply , Installation, repairs and other work by unqualified persons could be dangerous. , Do not drink water from the dishwasher! – The dishwasher can heat its own water to the temperature required by the wash program. This allows for connection of the machine to either a hot (max. 140°F / 60°C) or cold water source. Fo[...]

Drainage – The machine comes equipped with a built-in non-return valve on the discharge side to prevent waste water from flowing back into the dishwasher. – The dishwasher is equipped with a 5 ft (1.5 m) flexible drain hose with an internal diameter of 7/8" (22 mm). – Drain hose extensions and adapters can be ordered from Miele. The maxi[...]

General requirements for measuring noise The dishwasher must be loaded with 16 place settings and the Normal program must be used. Installation requirements for measuring noise The dishwasher must be installed as follows:. ^ Install the dishwasher into an appropriate housing unit. ^ Secure the front panel. Noise measurement 64[...]

^ Push the insulation mat supplied (depending on model) under the plinth until it is up against the appliance feet a . ^ Attach the toe-kick so that it is flush with the door front b . Noise measurement 65[...]

66[...]

67[...]

M.-Nr. 09 510 211 / 01 Alteration rights reserved / 0313 G5220/G5225 / INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.[...]