Moog Videolarm QODT4-70NA инструкция обслуживания

- 1 - GENERAL INSTRUCTIONS 1 . Remov e contents from the box. 2 . Remov e the existing ceiling tile from the desired location. 3 . Inser t the loose end of the saftey cord on the dome through the middle hole on the edge of the housing opening (Figure 1). Figure 1 4 . Align the eyelet on the cord with the hole located on the inside of the housing ti[...]

- 2 - CAMERA SETTINGS SERIAL NUMBERS BEGINNING WITH YK FIXED AND FIXED V ARI-FOCAL LENSES . There are no user adjustable settings on these units (Figure 4). Figure 4 AU TO IRIS LENSES. The dip s witches are factory set with AES off and backlight compensation on (Figure 5). The auto iris is also set at the factory , but an adjustment scre w is inclu[...]

SWITCH SETTING DEFINITION Flick er less Mode 1 Setting this switch to "On" and sw itch 3 (MIRIS) to "Off" will help to reduce the fl ic ker in fl uorescent lights Helps prev ent an object from being washed out when the object is directly in front of a light source. When the switch is in the on position the auto iris lens contr[...]

- 4 - ! ! NVT INSTR UCTIONS UNSHIELDED TWISTED P AIR VIDEO WIRING NO TE: The customer m ust purchase the Video T ransceiver from NVT . Part numbers are: • NV -212A (500 ft.) * NV -213A or NV -213A-M (1000 ft.) • NV -652R, NV -862R, or NV -1662R (3000 ft.) The cameras included in the Q-View™ series ha ve the option of transmitting video signal[...]

- 5 - 250 ft 250 ft 3 4 5 8 13 Ω 300 ft 300 ft 4 5 6 10 16 Ω 400 ft 400 ft 5 6 8 13 21 Ω 500 ft 500 ft 6 8 10 16 26 Ω 600 ft 600 ft 8 10 12 19 31 Ω 800 ft 800 ft 10 13 16 25 42 Ω 1000 ft 13 16 20 32 52 Ω 1250 ft 16 20 25 40 65 Ω 1500 ft 19 24 30 48 78 Ω 1750 ft 23 28 35 55 91 Ω 2000 ft 26 32 40 63 104 Ω 2500 ft 32 40 49 79 131[...]

! CAUTION RISK OF ELECTRIC SHOCK! CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT EXPOSE COMPONENTS TO WATER OR MOISTURE. SAFETY PRECAUTIONS IMPORTANT SAFEGUARDS 1. Read Instructions - All the safety and operating instructions should be read befor e the unit is operated. 2. Retain Instructions - The safety and operating instructions should [...]

- 8 - Po w er Supply Po w er A Po w er B Camera Assembly Primar y Po w e r Video Signal Video Shield Monitor (Ground Return) Figure A Ground Loop TR OUBLESHOO TING If you e xperience problems with the camera picture please check these simple troubleshooting procedures f or possible solutions bef ore calling technical suppor t. IMPORT ANT NO TE: If [...]

- 9 - AC V oltmeter Camera Monitor Bridge Tap NV-213 A NV-213 A NVT TROUBLESHOO TING If you are e xperiencing problems, attempt to simplify your setup . T est each cable segment separately . For e xample, test the camera and monitor together without the other equipment. Then add in the NVT transceiv ers, back-to-back. T est each segment of a long c[...]

- 10 - Use the formula below to select the correct po wer supply for camer as connected in parallel (positive to positiv e, negative to negativ e): T otal current for a 24 V AC system: TOT AL CURRENT = (202mA x total number of cameras) Example: 202mA x 5 total cameras = 1010mA Note: 202mA is camera plus power supply CAMERAS VOL T AGE CURRENT PO WER[...]

Pr oduct Registr ation / W arr anty Thank y ou for choosing Videolarm. W e value y our patr onage and are solely committ ed t o pr o viding you with only the highest quality pr oducts av ailable with unmatched customer service lev els that ar e second-t o-none in the security industr y . Should a pr oblem arise, r est assur e that Videolarm st ands[...]