Moog Videolarm WS1C-50NA-X2 инструкция обслуживания

P R O D U C T I N S T R U C T I O N S INST ALLA TION PREP ARA TION 1. Mount to a secure wall or ceiling. For outdoor application we also recommend that the housing be mounted in a protected area. 2. Complete all wire and conduit runs prior to installation. 3. Determine the mounting method: A. Mount directly to a wall or ceiling. B. Mount to a stand[...]

- 2 - CAMERA BRACKET SE TUP Once the housing is installed, the three axis camera bracket allows the camera to be adjusted to the desired viewing location and angle (Figure 6, next page). IMPORT ANT: A sticker has been placed on top of the lens holder of the camera to help in orienting the unit correctly . Figure 3 1. Connect the output of your Clas[...]

- 3 - Figure 7 CAMERA FOCUSING Fixed Lens: Loosen the set screw in the lens mount and to manually rotate the lens until a clear picture is achieved. Once the focus is set, retighten the set screw (Figure 7). Figure 6 Set screw Fixed lens Lens Bracket Lens Bracket Thumb Screws Camera Cradle Horizon Adjustment Thumb Screws Pan Adjustment Screw Horizo[...]

- 4 - 1. A cardboard template is included to test the adjustment of your lens/bracket setup before reattaching the housing top. Place the template over the lens/bracket set up, either on the back of the housing or in opposing front plate screw holes depending on the orientation of the setup. If the lens touches the cardboard the setup WILL touch th[...]

- 5 - Wiring Notes Wire — What to DO 1. DO use p oint-to -point Uns hielded T wist ed Pair wir e, gauge 24 o r thicker, str anded or so lid, Categ ory 2, 3, 4, or 5 . 2. The vi deo signa l may co-exi st in the sam e wire bund le as other video, te lephone , data, con trol signa ls, or low- voltage po wer . It is also OK t o run NVT video sig nals[...]

2 50 f t  3  4  5  8  13  W 3 00 f t  4  5  6  10  16  W 4 00 f t  5  6  8  13  21  W 5 00 f t  6  8  10  16  26  W 6 00 f t  8  10  12  19  31  W 8 00 f t  10  13  16  25  42  W 1 0 0 0 ft  13  16  20  32  52  W 1 2 5 0 ft [...]

P ower Supply P ower A P ower B Camera Assembly Primar y P ower Video Signal Video Shield Monitor - 7 - (Ground Return) Figure A Ground Loop TROUBLESHOO TING If you experience problems with the camera picture please check these simple troubleshooting procedures for possible solutions before calling technical support. IMPORT ANT NOTE: If you h[...]

A C Vo l t m e t e r Camera Monitor Bridge Tap NV-213 A NV-213 A - 8 - NV T TROUBLESHOO TING If you a re experi encing p roblems , attempt to simpl ify your setup. T e st each cable segment separate ly . For exa mple, te st the camera and monitor together with out the other equi pment. Then add in the NVT transce ivers, b ack-to-b ack. T es t each [...]

- 9 - Depending on the voltage being used, refer to one of the formulas below to select the correct power supply for cameras connected in parallel (positive to positive, negative to negative): T otal current for a 12 VDC system: TO T AL CURRENT = (350mA x total number of cameras) Example: 350mA x 5 total cameras = 1750mA T otal current for a 24 V A[...]

- 10 - WS1 - Exploded Diagram[...]

- 11 - P ar t Number Description Dealer Cost 1 RPWS1010 P ACKET ASSEMBL Y W ARRIOR 1& 3 HOUSINGS $17 2 RPWS1020 W ARRIOR 1 & 3 BASE ASSEMBL Y $45 3 RPWS1030 W ARRIOR 1 & 3 CARRIAGE ASSEMBL Y KIT $14 NTSC BOARD CAMERAS 4 RPWS1041F W ARRIOR 1 & 2 ST ANDARD RES, BLACK & WHITE, FIXED CAMERA KIT $144 RPWS1041V W ARRIOR 1 & 2 ST A[...]

- 12 - WS3 Exploded Diagram[...]

- 13 - WS3 Replacement P ar ts List P ar t Number Description Dealer Cost 1 RPWS1010 P ACKET ASSEMBL Y W ARRIOR 1 & 3 HOUSINGS $17 2 RPWS1020 W ARRIOR 1 & 3 BASE ASSEMBL Y $45 3 RPWS1030 W ARRIOR 1 & 3 CARRIAGE ASSEMBL Y KIT $14 NTSC BOARD CAMERAS 4 RPWS3041F W ARRIOR 3 & 4 ST ANDARD RES, BLACK & WHITE, FIXED CAMERA KIT $144 RPW[...]

- 14 - IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS UNPACKING SERVICE 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with damp cloth. 7 Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions. 8 Cable[...]

- 15 - LIMITED W ARR ANT Y FOR VIDEOLARM INC. PRODUC TS VIDEOLARM INC. warrants this Product to be free from defects in material or work manship, as follows: PRODUCTCA TEGORY P ARTS LABOR All Enclosures and Electronics Five (5) Y ears Five (5) Y ears Pan/T ilts Three (3) Y ears **6 months if used in autoscan Three (3) Y ears **6 months if used in a[...]

- 16 - Pr oduct Registration / W arranty Thank you for choosing Videolarm. W e value your patronage and ar e solely committed to providing you with only the highest quality products available with unmatched customer service levels that ar e second- to-none in the security industry . Should a problem arise, r est assure that Videolarm stands behind [...]