Moog Videolarm WS5-50NF инструкция обслуживания

PRODUCT INSTRUCTIONS I NSTALLATION PREPARATION 1. Determine the mounting location. Be sure that you’ll be mounting to a secure wall or ceiling, next to a stud. 2. Complete all wire and conduit runs prior to installation of the housing. R EVI S I ON D A T E: 02-02-2009 Depending on the voltage being used, refer to one of the formulas below to sele[...]

- 2 - CAMERA BRACKET SETUP Reattach the camera bracket to the double-gang box using the (2) 8-32 screws. Check to determine if the position of the camera is correct. T o adjust the bracket, loosen the (2) 8-32 adjustment screws (Figure 7). Use Loctite™ or an equivalent product to secure the screws, especially in installations where vibration is a[...]

- 3 - Figure 8 CAMERA FOCUSING (Figure 8) 1. The camera is factory equipped with a 3.6mm xed lens. A 2.5mm lens is also provided. T o remove the 3.6mm lens, loosen the set screw and unscrew the lens counter-clockwise. 2. Fine focusing of the lens: Loosen the set screw in the lens mount and manually rotate the lens until a clear picture is achiev[...]

- 4 - ADDENDUM 1 The cameras included in the W arrior series are able to transmit video signals to NVT receivers via unshielded twisted pair cable. Y ou must purchase the receiver separately . Instructions for connecting the receiver end of the unshielded twisted pair cable will be included with the NVT receiver . Following are instructions for con[...]

2 50 f t 3 4 5 8 13 � 3 00 f t 4 5 6 10 16 � 4 00 f t 5 6 8 13 2 1 � 5 00 f t 6 8 10 16 26 � 6 00 f t 8 10 12 19 31 � 8 00 f t 10 1 3 16 2 5 42 � 1 0 0 0 f t 13 1 6 20 3 2 52 � 1 2 5 0 f t 16 2 0 25 4 0 65 � 1 5 0 0 f t 19 2 4 30 4 8 78 � 1 7 5 0 f t 23 2 8 35 5 5 91 � 2 0 0 0 f t 26 3 2 40 6 3 10 4 � 2 5 0 0 f t 32 4 0 49 7 9[...]

! CAUTION RISK OF ELECTRIC SHOCK! CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT EXPOSE COMPONENTS TO WATER OR MOISTURE. SAFETY PRECAUTIONS IMPORTANT SAFEGUARDS 1. Read Instructions - All the safety and operating instructions should be read befor e the unit is operated. 2. Retain Instructions - The safety and operating instructions should [...]

7 6 5 4 3 2 1 WS5 - Exploded Diagram and Replacement Parts List Part Number Description 1 RPWS5010 W ARRIOR 5 FRONT PLA TE ASSEMBL Y 2 RPWS5020 W ARRIOR 5 F ACE PLA TE F ASTENER KIT 3 WS5PS W ARRIOR 5 REPLACEMENT P AINT SHIELD 4 RPWS5040 W ARRIOR 5 REPLACEMENT WINDOW KIT NTSC BOARD CAMERAS 5 RPWS5050 W ARRIOR 5 ST ANDARD RES, BLACK & WHITE, FIX[...]

P ower Supply P ower A P ower B Camera Assembly Primar y P ower Video Signal Video Shield Monitor A C Vo l t m e t e r - 8 - (Ground Return) Figure A Ground Loop TROUBLESHOOTING If you experience problems with the camera picture please check these simple troubleshooting procedures for possible solutions before calling technical support. IMPORT ANT [...]

Camera Monitor Bridge Tap NV-213 A NV-213 A - 9 - If t he v oltage is g reater than 1/2 vo lt, use an amplifie d r eceiver, such as the N V -65 2R, NV -862R, or NV-1662R. Alternate ly , remove the gr ound at one end (usu ally at the camer a end). Be sur e t hat floatin g the camera con forms to loca l/region al and Natio nal Electr ical Codes . NO [...]

- 10 - Depending on the voltage being used, refer to one of the formulas below to select the correct power supply for cameras connected in parallel (positive to positive, negative to negative): T otal current for a 12 VDC system: TOT AL CURRENT = (350mA x total number of cameras) Example: 350mA x 5 total cameras = 1750mA T otal current for a 24 V A[...]

Pr oduct Registr ation / W arr anty Thank y ou f or choosing Videolarm. W e value y our patr onage and ar e solely committed t o pr oviding y ou with only the highest quality products a v ailable with unmatched cust omer service lev els that ar e second-t o-none in the security industry . Should a pr oblem arise, r est assur e that Videolarm stands[...]