NEC MultiSync L227HR инструкция обслуживания

MultiSync E222W User ’ s Manual[...]

Index W arning, Caution ............................................................................................................... .......... English-1 Registration Information ....................................................................................................... ........ English-1 Recommended use .............................[...]

English English-1 W ARNING CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM W ALL SOCKET . T O FULL Y DISENGAGE THE POWER TO THE UNIT , PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET . DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE P ARTS INSIDE. REFER SER VICING T O QUALIFIED SERVICE PERSONNEL.[...]

English-2 Canadian Department of Communications Compliance Statement DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1. FCC Information 1. Use the attached specif[...]

English English-3 Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MUL TISYNC LCD COLOUR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer al[...]

English-4 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONIT OR CAN REDUCE EYE, SHOULDER AND NECK F A TIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Y our eyes should look slightly downward [...]

English English-5 Contents Y our new NEC MultiSync LCD monitor box* should contain the following: • MultiSync LCD monitor with tilt/swivel/pivot/height adjust base • Power Cord • Base stand •V ideo Signal Cable (15-pin mini D-SUB male to 15-pin mini D-SUB male) •V ideo Signal Cable (DVI-D to DVI-D) • Setup Manual Power Cord (T ype of po[...]

English-6 Quick Start To attach the Base to the LCD stand: 1. Place monitor face down on a non-abrasive surface ( Figure 1 ). NOTE: Handle with care when monitor facing down, for avoiding damage to the front control buttons. 2. Please pivot base 90 degrees as shown in Figure 1 . NOTE: Handle with care when pulling the stand. 3. Attach the base stan[...]

English English-7 Figure C.1 Power Button Figure RL.1 Raise and Lower Monitor Screen The monitor may be raised or lowered. T o raise or lower screen, place hands on each side of the monitor and lift or lower to the desired height ( Figure RL.1 ). NOTE: Handle with care when raising or lowering the monitor screen. T ilt and Swivel Grasp both sides o[...]

English-8 Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes: 1. Disconnect all cables. 2. Place monitor face down on a non-abrasive surface ( Figure S.1 ). NOTE: Handle with care when monitor facing down, for avoiding damage to the front control buttons. 3. Remove the 4 screws connecting the stand to the monit[...]

English English-9 7. Reverse this process to re-attach stand. NOTE: Use only VESA-compatible alternative mounting method. Handle with care when removing stand. NOTE: Match “TOP SIDE” mark on stand to top side of the monitor head when re-attaching stand. Flexible Arm Installation This LCD monitor is designed for use with a flexible arm. T o moun[...]

English-10 Menu Open OSD main menu. Exits the OSD controls. Exits to the OSD main menu. Button MENU Controls OSD (On-Screen Display) control buttons on the front of the monitor function as follows: To access OSD menu, press any of the control buttons (MENU, Left, Right, Down, Up). To change signal input, press the SELECT button. To change DV MODE, [...]

English English-11 Image Controls (Analog input only) LEFT / RIGHT Controls Horizontal Image Position within the display area of the LCD. DOWN / UP Controls V ertical Image Position within the display area of the LCD. H.SIZE Adjusts the horizontal size by increasing or decreasing this setting. FINE Improves focus, clarity and image stability by inc[...]

English-12 Information The Information menu indicates the current input, display resolution, horizontal and vertical frequency , and polarity settings of the monitor . The model and serial numbers of your monitor are also indicated. CARBON SA VINGS: Display the estimated carbon saving information in kg. The carbon footprint factor in the carbon sav[...]

English English-13 Specifications Monitor Specifications MultiSync E222W Notes LCD Module Diagonal: 55.9 cm/22.0 inches Active matrix; thin film transistor (TFT) liquid V iewable Image Size: 55.9 cm/22.0 inches crystal display (LCD); 0.282 mm dot pitch; Native Resolution (Pixel Count): 1680 x 1050 250 cd/m 2 white luminance; 1000:1 contrast ratio, [...]

English-14 Features Thin-frame design creates more desktop space for you to work and play , while the flat screen’s crisp, bright images and crystal- clear text deliver a comfortable viewing experience. No T ouch Auto Adjust automatically adjusts your optimal image settings upon initial power-on. Colour Control System allows you to change between[...]

English English-15 T roubleshooting No picture • The signal cable should be completely connected to the display card/computer . • The display card should be completely seated in its slot. • Front Power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode has been selected on the display c[...]

English-16 TCO Displays 5.0 Congratulations! This display is designed for both you and the planet! The display you have just purchased carries the TCO Certified label. This ensures that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high perf[...]

English English-17 NEC DISPLA Y SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’ s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally- friendly products, and always strive to help define and comply with the latest independent [...]