Oki 407II инструкция обслуживания

[...]

Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and f ound to comply with the limits for a Class A digital de vice, pursuant to Part 15 of the FCC Rules . These limits are designed to provide reasonable protection against har mful interf erence when the equipment is operated in a commercial en[...]

T ABLE OF CONTENTS 1. Unpacking and Installation ..................................................................................................................... 1 1-1. Unpacking .................................................................................................................................... 1 1-2. Choosing a place for the p[...]

1 1-4. Ethernet Interface Model ........................................................................................................... 47 1 1-5. W ireless LAN Interface Model .................................................................................................. 48 12. Parallel Interface .............................................[...]

– 1 – 1. Unpac king and Installation 1-1. Unpacking After unpacking the unit, check that all the necessary accessories are included in the package. Note: The ferrite core and fastener provided with your printer depend on your printer conguration. Fig. 1-1 Unpacking If anything is missing, contact the dealer where you bought the printer and a[...]

– 2 – 1-2. Choosing a place for the printer Before actually unpacking the printer , you should take a few minutes to think about where you plan to use it. Remember the following points when doing this. Choose a rm, level surface where the printer will not be exposed to vibration. T he pow er o utl et y ou p lan t o co nnec t t o for powe r s[...]

– 3 – 2. P ar ts Identification and Nomenc lature Interf ace connector F or connection to a host computer . P eripheral drive connector Connects to peripheral units such as cash dra wers, etc. Do not connect this to a telephone. P ower connector F or connection of the A C adapter . Ne ver unplug the A C adapter while the printer is on. Printer[...]

– 4 – 3. Setup 3-1. Connecting the Cable to the PC 3-1-1. Parallel Interface Cable Connect the parallel interface cable to a parallel port of your PC. 3-1-2. RS-232C Interface Cable Connect the RS-232C interface cable to a RS-232C port of your PC. 3-1-3. USB Interface Cable Connect the USB interface cable to a USB port of your PC. 3-1-4. Ethern[...]

– 5 – 3-2. Connecting the Cable to the Printer Note that the interface cable is not provided. Please use a cable that meets specications. CAUTION Befor e connecting/disconnecting the interface cable, make sur e that power to the printer and all the devices connected to the printer is turned off. Also make sur e the power cable plug is discon[...]

– 6 – 3-2-2. RS-232C Interface Cable (1) Make sure the printer is turn of f. CAUTION Befor e connecting/disconnecting the interface cable, make sur e that power to the printer and all the devices connected to the printer is turned off. Also make sur e the power cable plug is disconnected fr om the AC outlet. (2) Connect the interface cable to t[...]

– 7 – 3-2-4. Connecting Ethernet Cable When using an Ethernet cable that is 10 m or less, shielded cable is recommended. (1) Make sure the printer is turned of f. (2) Afx the ferrite core onto the ethernet cable as shown in the illustration below . (3) Pass the fastener through the ferrite core. ( 4) Loop the fastener around the cable and lo[...]

– 8 – 3-3. Installing the Printer Software Here is the procedure for installing the printer driver and utility software, which are stored on the supplied CD-ROM. The procedure applies to the W indows operating systems shown below . • W indows 2000 • W indows XP • W indows V ista ( 1) T urn ON the power to your PC to start W indows. (2) In[...]

– 9 – 3-4. Connecting the Optional AC Adapter Note: Before connecting/disconnecting the AC adapter , make sure that power to the printer and all the devices connected to the printer is turned off. Also make sure the power cable plug is disconnected from the AC outlet. (1) Connect the AC adapter to the power cable. Note: Use only the standard AC[...]

– 10 – 3-5. T urning Power On Make sure that the Power cord has been connected as described in 3-4. T urn ON the power switch located on the front of the printer . The POWER lamp on the control panel will light up. CAUTION W e r ecommend that you unplug the printer fr om the power outlet whenever you do not plan to use it for long periods. Beca[...]

– 1 1 – 3-6. Connecting to a Peripheral Unit Y ou can connect a peripheral unit to the printer using a modular plug. See “Modular plug” on page 58 for details about the type of modular plug that is required. Note that this printer does not come with a modular plug or wire, so it is up to you to obtain one that suits your needs. CAUTION Make[...]

– 12 – 3-7. Loading the Paper Roll Be sure to use paper roll that matches the printer ’ s specication. Cov er open lev er P aper roll T ension bar 1 Push the cover open lever and open the printer cover . 2 Set the paper rol l in the direction as shown, and pull on the leading edge of the paper towards you. Note: Make sure not to pass the p[...]

– 13 – 3-7-1. Removing the T ension Bar When using thermal paper roll, the tension bar unit may or may not be necessary , depending on the paper thickness, paper width, or the installation layout. If the tension bar unit is unnecessary , remove it in accordance with the procedure indicated below . The tension bar unit is unnecessary when using [...]

– 14 – 3-7-2. Changing the Adjustment Lever Position The adjustment lever position must be changed in accordance with the paper thickness. It is factory-set to position ① . When using paper thickness between 100 and 150 μm, change the adjustment lever position in accordance with the procedure below . As shown, use a at head screwdriver to[...]

– 15 – Caution Symbol This symbol is placed near the thermal head to indicate that it may be hot. Never touch the thermal head immediately after the printer has been used. Let the thermal head cool for a few minutes before touching it. This symbol is placed near the thermal head to indicate that it is easily damaged. Observe the precautions for[...]

– 16 – Notes on Using the Auto Cutter 1) T o print after a cut, feed 1 mm (8-dot line) or mor e of paper . 2) If the cutter is not in its home position after an err or , rst eliminate the cause of the err or; then, turn the power back ON. 3) If the printer is placed horizontally , the use of the partial cut is r ecommended. If you use the fu[...]

– 17 – 4. Attaching the Accessories The following accessories do not necessarily have to be attached. Attach them if necessary . • Holding plate • Cable cover • Switch blind Shaft 82.5 or 79.5 mm width 57.5 mm width 4-1. Attaching the Holder Plate (1) Attach the shaft to the printer . (2) W ipe the area into which the rubber feet will be [...]

– 18 – (4) Attach the holding plate to the printer . Then tighten the two screws that were supplied to secure it in place. (5) Pos itio n th e p rin ter ove r t he sc rew s, etc. , on th e wa ll and then slide it downward to set it in place. CAUTION The weight of the printer , including a r oll of paper with the lar gest diameter , is appr oxim[...]

– 19 – 4-2. Attaching the Switch Blind Attach the switch blind as shown in the illustration. 4-3. Switch Blind Installation It is not necessary to install the switch blind. Only install it if it is necessary for you. By install - ing the switch blind, the following become possible. • Preventing the power switch from being operated by mistake.[...]

– 20 – 5. Consumable P ar ts and A C Adapter When consumable parts have run out, use those specied in the table below . Make sure that the AC adapter specied in the table is used. Use of consumable parts or AC adapter which are not specied in the table may result in dam - age to the printer , re or electric shock. 5-1. Thermal Paper[...]

– 21 – Manufacture Product name Quality characteristics/Use Paper thickness (µm) Oji Paper Co., Ltd. PD150R normal type paper 75 PD160R high image stability paper 65/75 PD750R 2 color paper: Red & Black 75 PD700R 2 color paper: Blue & Black 75 Nippon Paper Industries TF50KS-E2C normal type paper 65 Kanzaki Speciality Papers Inc. (KSP) [...]

– 22 – 5-2. Full-Face Thermal Label Paper Roll (1) Label paper specication Backing paper width: 79.5±0.5 mm or 82.5±0.5 mm Outer roll diameter: ø100 mm or less T ake up paper roll width: 80 +0.5 -1 mm or 83 +0.5 -1 mm Thickness: Max. 150 μm Core outer/inner diameter: core inner diameter ø25.4±1 mm/core outer diameter ø32±1 mm Printed[...]

– 23 – (3) Ef fective Print W idth Paper W idth (mm) Right / Left Margin (mm) Effective Print W idth (mm) Number of Print Columns (12 × 24 Font) 79.5 ± 0.5 4 72 48 82.5 ± 0.5 Left -2 to 1, Right 1.5 to 3 80 53 Left Margin Right Margin Effectiv e Print Width P aper Width 5-3. Thermal Label Paper Roll (T ack Label Paper) (1) Label paper speci?[...]

– 24 – (2) Recommended label paper Manufacturer Product name Quality features/ applications Thickness (μm) Adhesion type Base material Separator T otal thickness Lintec LD21 14 For distribution or information control 65 41 1 15 High adhesion Lintec LD5530 For measurement 85 65 150 High adhesion Ricoh 130LHB For distribution or information cont[...]

– 25 – 5 ø100 MAX ø32 ± 1 ø25.4 ± 1 15MIN (1.75) 1.75 ± 0.5 5 ± 1.0 5 ø100 MAX 80 +0.5 -1.0 (Rolled dimension) ø32 ± 1 ø25.4 ± 1 1 +1.0 -0.8 15 MIN (1.75) 76 ± 0.5 (Label width) 79.5 ± 0.5 (Backing paper width) 1.75 ± 0.5 5 ± 1.0 35 – 300 (Black mark pitch) 30 – 295 (Label length) • Detailed Diagrams of Recommended T ack L[...]

– 26 – • Detailed Diagram of Effective Printing Range 3 (Bottom margin) (1.75) 82.5 mm backing paper 1.75 ± 0.5 4.5 (T op margin) 3 (Left margin) 3 (Right margin) 22.5 – 287.5 (Effectiv e printing length) 30 – 295 (Label length) 35 – 300 (Black mark pitch) 79 ± 0.5 (Label width) 82 .5 ± 0.5 ( Bac kin g pa pe r w id th ) 73 (effectiv [...]

– 27 – 2.5 2.5 5 • Cut Position / Printing Line / Black Mark Sensor ’ s Positional Relationship Cut position Printing line Black mark sensor Approx. 13 Approx. 14 5-4. AC adapter (option) AC adapter which are not specied may result in damage to the printer , re or electric shock. Model name: PS60A-24A Input: 100 to 240 V AC, 50/60 Hz [...]

– 28 – 6. Contr ol P anel and Other Functions 6-1. Contr ol Panel ① POWER lamp (Green LED) When the printer is online, power lamp is ON and ERROR lamp is OFF . ② ERROR lamp (Red/Orange LED) Indicates various errors in combination with POWER lamp. ③ FEED button Press the FEED button to feed paper roll. 6-2. Err ors 1) Recoverable errors Er[...]

– 29 – 2) Non-recoverable errors Error Description POWER Lamp ERROR Lamp Recovery Conditions Flash access error OFF Flashes Orange lamp at 0.5-sec - ond intervals This is not a recoverable error . EEPROM error OFF Flashes Red lamp at 0.75- second intervals This is not a recoverable error . SRAM error OFF Flashes Orange lamp at 1-sec - ond inter[...]

– 30 – 6-3. Self-Printing 6-3-1. T est Printing Place the thermal paper roll on the printer . T urn the power ON while holding the FEED button depressed. The printer will run a test print according to the V er . No., DIP switch settings, and memory switch settings, etc. 6-3-2. Hexadecimal Dump Mode Place the thermal paper roll on the printer . [...]

– 31 – 7. Adjusting the Near -end Sensor Use the following procedure to adjust the near-end sensor so it is compatible with the size of paper roll you are using. However , for vertical or wall-mount use, keep the adjuster xed to level 3, without changing its position. ① Open the printer cover . ② Determine the diameter of the paper roll [...]

– 32 – Adjustment value according to the paper you are using Paper thick-ness (µm) When using the paper roll with a core whose inside diameter (A):ø12, outside diameter (B):ø18 Detected diameter (C) (Approx. mm) Remained paper length (Approx. m) Level 1 Level 2 Level 3 Level 1 Level 2 Level 3 65 ø23 ø27 ø31 2.5 4.9 7.7 75 2.1 4.2 6.7 Pape[...]

– 33 – 8. Pre venting and Clearing P aper Jams 8-1. Pr eventing Paper Jams The paper should not be touched during ejection and before it is cut. Pressing or pulling the paper during ejection may cause a paper jam, paper cutting failure or line feed failure. 8-2. Removing Paper Jam If a paper jam occurs, clear it as described below . (1) Set the[...]

– 34 – 9. P eriodical Cleaning Printed characters may become partially unclear due to accumulated paper dust and dirt. T o prevent such a problem, paper dust collected in the paper holder and paper transport section and on the surface of the thermal head must be removed periodically . Such cleaning is recommended to be carried out once six mont[...]

– 35 – 10. Specifications 10-1. General Specications (1) Printing method Direct line thermal printing (2) Print speed Max. 2000 dots/sec. (250 mm/sec.) ( 3) Dot density 203 dpi: 8 dots/mm (0.125 mm/dot) (4) Printing width Max. 80 mm ( 5) Number of print columns 53 (12 × 24 dots) (6) Paper roll Refer to chapter 4 for details on the recommen[...]

– 36 – 10-2. Auto Cutter Specications (1) Cutting frequency Max. 20 cuts per minute (2) Thickness of paper 0.065 ~ 0.15 mm 10-3. Interface RS-232C serial interface/T wo-way parallel interface (IEEE1284)/USB interface/Ethernet in- terface/W ireless LAN Interface 10-4. Electrical Characteristics (1) Input V oltage DC 24 V±10% (2) Current Cons[...]

– 37 – 10-5. Envir onmental Requir ements (1) Operating T emperature 5°C to 45°C Humidity 10% to 90% RH (without condensation) ( 2) T ransport/storage (except for paper) T emperature -20°C to 60°C Humidity 10% to 90% RH (without condensation) (%RH) 34°C90% RH 40°C65% RH 45°C50% RH 90 80 60 40 20 10 0 10 20 30 40 50 T emperature (°C) Ope[...]

– 38 – 10-6. Reliability Specications (1) MCBF: 60 million lines • Recommended thermal paper (60 μm to 75 μm) • A verage printing rate: 12.5% • Printing density: standard setting Note: The Mean Cycles Before Failure (MCBF) with the recommended thermal paper thickness between 75 μm and 150 μm is 25 million lines. (2) Auto cutter (li[...]

– 39 – 10-7. Black mark specications <Remarks> 1) The cut position shown above is when the print starting position correct value for Appendix F: memory switch 9 is the default setting. 2) The black mark’ s PCS value must be 0.90 or more. 3) Note that accuracy of starting printing with the black mark sensor must be within ±2 mm of th[...]

– 40 – 11. Dip Switch Setting T wo DIP switches are provided at the bottom of the printer , and can be set as given in the table below . Be sure to set the power switch to of f before changing the settings. It is recommended to use a pointed item like a pen or at-blade driver screw to change the settings. The settings will become ef fective [...]

– 41 – 1 1-1. Parallel Interface Model ON ON OFF OFF DIP-SW 1 Switch 1-1 Command emulation ON Star Mode OFF ESC/POS Mode The factory settings of DIP switch are all on. The functions of switches 1-2 through 1-10 will change according to the command emulation that has been set using switch 1-1. (1) Star mode Switch Function ON OFF 1-1 Command emu[...]

– 42 – DIP-SW 2 Switch Function ON OFF 2-1 Always ON Should be set to on 2-2 2-3 2-4 The factory settings of DIP switch are all on.[...]

– 43 – 1 1-2. RS-232C Interface Model ON ON OFF OFF DIP-SW 1 Switch 1-1 Command emulation ON Star Mode OFF ESC/POS Mode The factory settings of DIP switch are all on. The functions of switches 1-2 through 1-10 will change according to the command emulation that has been set using switche 1-1. (1) Star mode Switch Function ON OFF 1-1 Command emu[...]

– 44 – DIP-SW 2 Switch Function ON OFF 2-1 Always ON Should be set to on 2-2 2-3 2-4 The factory settings of DIP switch are all on.[...]

– 45 – The following is the procedure for changing the settings on DIP switch No. 3. 1. T urn off the printer and all components connected to it. 2. Remove the 2 screws. 3. Remove the serial interface board unit. 4. Change the setting of the DIP switches. 5. Replace the serial interface board unit. Then secure it with the screws. 6. T urn on th[...]

– 46 – 1 1-3. USB Interface Model ON ON OFF OFF DIP-SW 1 Switch Function ON OFF 1-1 Command emulation (Ster Line mode) Always ON 1-2 Should not be changed (Should be set to on) 1-3 Should not be changed (Should be set to on) 1-4 Sensor adjustment Invalid V alid 1-5 USB mode Printer class V endor class 1-6 Handshaking conditions (conditions for [...]

– 47 – 1 1-4. Ethernet Interface Model ON ON OFF OFF DIP-SW 1 Switch Function ON OFF 1-1 Command emulation (Ster Line mode) Always ON 1-2 Should not be changed (Should be set to on) 1-3 Should not be changed (Should be set to on) 1-4 Sensor adjustment Invalid V alid 1-5 Should not be changed (Should be set to on) 1-6 Handshaking conditions (con[...]

– 48 – ■ Initializing Settings Set the push switch as described below to initialize the setting information. Push the switch for one to ve seconds while running under normal operating mode. The green and red LEDs will ash with a regular pattern. After that, push the switch once again in that state to turn OFF both of the red and green L[...]

– 49 – DIP-SW 2 Switch Function ON OFF 2-1~2-4 Always ON Should be set to on The factory settings of DIP switch are all on. DIP Switch ON OFF 3-1 Fixed at OFF 3-2 Initialize of setting information — Change DIP Switch 3-2 to ON initialize the setting information when the power is turned on. The factory settings of DIP switch are all of f. LED [...]

– 50 – Note: • This product contains a built-in wireless device and can only be used in the following countries. USA, UK, France, Ireland, Belgium, Germany , Austria, Switzerland, Italy , Denmark, Norway , Sweden, Portugal, Spain, Estonia, Finland, Greece, Luxemburg, Netherlands, Canada, Slovakia, Slovenia, Czech, Hungary , Poland, Latvia, an[...]

– 51 – Connecting the peripheral drive cable Connect the peripheral drive cable to the connector on the printer . Then, connect the other end of the cable to the peripheral drive circuit. Except f or EU F or EU[...]

– 52 – 12. P arallel Interface The two-way parallel interface is compatible with the IEEE1284 compatibility mode and nibble mode. Refer to the separate Specications Manual for details. T able of Connection Signals for Each Mode Pin No. Direction Compatibility Mode Signal Name Nibble Mode Signal Name 1 In nStrobe Host Clock 2 In/Out Data0 Dat[...]

– 53 – A: Star t bit B: Data bit C: P ar ity bit D: Stop bit ! " # $ B B B B B B B B 13. RS-232C Serial Interface 13-1. Interface Specications ① Data transmission method: Asynchronous serial interface ② Baud rate: Selectable from 4800, 9600, 19200, 38400 bps (Refer to “1 1. DIP Switch Setting”.) ③[...]

– 54 – 13-2. RS-232C Connector Pin No. Signal name Direction Function 1 F-GND — Frame ground 2 TXD OUT T ransmission data 3 RXD IN Receive data 4 R TS OUT Same as DTR signal. 5 N/C Not used 6 DSR IN ST AR Mode Status of this signal is not checked. ESC/POS Mode In DTR/DSR communication mode, indicates whether data receive from host is enabled [...]

– 55 – Pin No. Signal name Direction Function 1) DTR/DSR Communication Mode This signal indicates whether the printer is busy . SP ACE indicates that the printer is ready to receive data, and MARK indicates that the printer is busy . The busy condition can be changed by using DIP SW 1-6 as follows: Printer status DIP SW 1-6 OFF ON 1. During the[...]

– 56 – 13-3. Cable Connections The followings are a recommended interface cable connections. Note: Use shielded wire less than 3 m in length. 13-4. Electrical Characteristics V oltage Data signal Control signal Binary status -3 V to -15 V Mark OFF 1 +3 V to +15 V Space ON 0 1 2 3 4 5 6 1 2 3 4 5 6 7 8 20 FG FG TXD RXD RTS CTS DSR 20 25 7 SG DTR[...]

– 57 – 14. USB, Ethernet and Wireless LAN Interface 14-1. USB Interface Specications 1. General Specication: Conforms to USB 2.0 Specications 2. Communication Speed: USB Full Speed Mode (12 Mbps) 3. Communication Method: USB Bulk T ransmission Mode 4. Power Specications: USB Self-power Function 5. Connector: USB Up-Stream Port Conne[...]

– 58 – Modular plug Pin No. Signal name Function I/O direction 1 FG Frame ground — 2 DRD1 Drive signal 1 OUT 3 +24 V Drive power OUT 4 +24 V Drive power OUT 5 DRD2 Drive signal 2 OUT 6 DRSNS Sense signal IN 15. P eripheral Unit Drive Cir cuit Peripheral unit drive circuit connector only connects to peripheral units such as cash drawers, etc. [...]

– 59 – Note: 1. Pin 1 must be shield drain wire connected to peripheral device frame ground. 2. It is not possible to drive two drives simultaneously . 3. The peripheral drive duty must satisfy the following: ON time / (ON time + OFF time) 0.2 4. Minimum resistance for coils L1 and L2 is 24 Ω. 5. Absolute maximum ratings for diodes D1 and D2 [...]

– 60 – 16. Memor y Switc h Settings Each memory switch is stored in EEPROM. For details on the functions and settings of memory switches, see the separate Specication Manual. The table below shows the factory settings for the memory switches. Memory Switch Hexadecimal Code 0 0000 1 0000 2 0000 3 0000 4 0000 5 0000 6 0000 7 0000 8 0000 9 0000[...]

Oki Data Americas, Inc., 2000 Bishops Gate Blvd., Mt.Laurel, NJ 08054-4620 T el: 1-800-Oki-Data (1-800-654-3282) Fax: (856) 222-5320 www .okiprintingsolutions.com Oki Data de Mexico, S.A. de C.V ., Mariano Escobedo NO. 748-8 Piso, Col. Anzures, e.p. 1 1590, Mexico, DF T el: 52-555-263-8780 Fax:52-555-250-3501 www .okiprintingsolutions.com[...]