Onkyo TX-NR1010 инструкция обслуживания

E n AV RECEIVER TX-NR1010 Instruction Manual Contents Safety Information and Introduction ............ 2 Table of Contents ............. .............. ........... ..... 6 Connections ....... .............. ........... .............. ... 13 Turning On & Basic Operati ons .................. 23 Advanced Operations .............. .............. ..[...]

En-2 Safety Information and Introduction Important Safety Instructions 1. Read these instruct ions. 2. Keep these instructi ons. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this a pparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilat ion openings. Install in accordance with the manuf acturer’s instruc[...]

Safety Information and Introduction En-3 Precautions 1. Recording Copyright —Unless it’s for personal use only, recording copyrighted ma terial is illegal without the permission of the copyright holder. 2. AC Fuse —The AC fuse inside the unit is not user- serviceable. If you cannot tu rn on the unit, contact your Onkyo dealer. 3. Care —Occa[...]

Safety Information and Introduction En-4 For Canadian Models NOTE: THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003. For models having a power co rd with a polarized plug: CAUTION: TO PREVENT ELECT RIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. Modèle pour les Canadien REMARQUE: CET APPAREIL NUMÉRIQUE DE LA CLASSE B[...]

Safety Information and Introduction En-5 Supplied Accessories Make sure you have the following accessories: * In catalogs and on p ackaging, the letter at the end of the product name indicates the color. Specifi cations and opera tions are the same regardless of color. ■ Installing the batteries Note • If the remote controller doesn’t w ork r[...]

Safety Information and Introduction En-6 Table of Contents Safety Information and Intro duction Important Safety Instructions ......................................2 Precautions ................................................................... 3 Supplied Accessories......................... .......................... 5 Table of Contents .........[...]

Safety Information and Introduction En-7 Features Amplifier • 140 Watts/Channel @ 8 ohms (FTC) • 200 Watts/Channel @ 6 ohms (IEC) • WRAT–Wide Range Amplifier Technology (5 Hz to 100 kHz bandwidth) • Linear Optimum Gai n Volume Circuitry • H.C.P.S. (High Current Po wer Supply) Massive High Power Transformer • 3 Stage Inverted Dar lingt[...]

Safety Information and Introduction En-8 Front & Rear Panels Front Panel (North American models) (European models) d e c f gh b a ij l m o p t q s n u w x y v k r z[...]

Safety Information and Introduction En-9 For detailed informat ion, se e the pages in parentheses. a 8 ON/STANDBY button ( 23 ) b Remote control sensor ( 5 ) c Display ( 10 ) d MASTER VOLUME control and indicator ( 26 , 51 ) e HYBRID STANDBY indicator ( 59 ) f PURE AUDIO button and indicator ( 42 ) g Input sele ctor buttons ( 26 ) h Front flap Gent[...]

Safety Information and Introduction En-10 s For detailed informat ion, se e the pages in parentheses. a Speaker/ channel indicat ors b Z2 (Zone 2) indicator ( 85 ) c Z3 (Zone 3) indicator ( 85 ) d Listening mode and format indicators ( 42 , 77 ) e M.Opt indicator ( 57 ) f 1 , 3 and cursor indi cators ( 28 ) g NET indicator ( 29 to 33 , 82 ) h Tunin[...]

Safety Information and Introduction En-11 a RS232 port Terminal for control. b DIGITAL IN COAXIAL and OPTICAL jacks c USB port d ETHERNET port e u REMOTE CONTROL jack f HDMI IN and HDMI output ( HDMI OUT MAIN and HDMI OUT SUB / ZONE 2 ) jack s g COMPONENT VIDEO IN and MONITOR OUT jacks h IR IN and OUT jacks i ZONE 2 and ZONE 3 12V TRIGGER OUT jack [...]

Safety Information and Introduction En-12 Remote Controller For detailed informat ion, se e the pages in parentheses. a 8 RECEIVER button ( 23 ) b ACTIVITIES buttons ( 53 , 96 ) c REMOTE MODE/INPUT SELECTOR buttons ( 26 ) d SP (speaker layout) button ( 52 ) e q / w / e / r and ENTER buttons f Q SETUP button ( 54 ) g Listening Mode buttons ( 42 ) h [...]

En-13 Connections Connecting the AV Receiver Speaker Configuration The following table indicates the channels you should use depending on the number of speakers that you have. No matter how many speakers you use, 2 powered subwoofers are recommended for a really powerful and solid bass. To get the best from your surround sound system, you need to s[...]

Connections En-14 ■ 9.2-channel playback By adding an external amplifier to the 7.2-channel configuration, you can enjoy 9.2-channel playback. Connect your power amplifier’s analog audio input jacks to the AV receiver’s SB / FH / FW *1 EXT AMP jacks with audio cables. To use the SB / FH / FW EX T AMP jacks, you must specify their channel with[...]

Connections En-15 • Don’t connect more than one cable to each speaker terminal. Doing so may damage the AV receiver. • Don’t connect one speake r to several terminals. Using Dipole Speakers You can use dipole speakers for the surround and surround back speakers. Dipole speakers output the same sound in two directions. Dipole speakers typica[...]

Connections En-16 Bi-amping the Front Spea kers Bi-amping provides improved bass and treble perf ormance. When bi-amping i s used, the AV rece iver is able to drive up to a 5.2 speaker system in the main room. Once you’ve completed the bi-amping connections as shown and turned on the AV receiver, you must set the speaker setting to enable bi-a mp[...]

Connections En-17 Connecting AV components a *1 If your TV doesn ’t support Audio R eturn Channel (A RC), you need to connect an optical di gital cable together with the HDMI cable to the AV receiver. • Before making any AV connections, read the manuals supplied with your AV components. • Don’t connect the power cord until you’ve complete[...]

Connections En-18 * If your TV doesn’t suppo rt Audi o Return Channe l (ARC), you need to connect an optical digita l cable toge ther with the HDMI cable to the AV receiver. * When listening to an HDM I component through the AV receiver, set the HDMI component so that its video can be seen on the TV screen (on the TV, select the input of the HDMI[...]

Connections En-19 Connecting Your Components The on-screen menus appe ar only on a TV that is connected to HDMI OUT MAIN . If your TV is connected to other video outputs, use the AV receive r’s display when changing settings. C B A D A E F G I H GND screw Connect your components to the appropriate jacks. The default input assignment s are shown b[...]

Connections En-20 Note *1 Do not connect the AV receiver ’s USB port to a USB port on your computer. Music on your co mputer cannot be played through the AV receiver in this way. *2 Only the front-panel USB in put is compatible wit h iPod/iPhone. *3 When the USB input is selected, yo u can input video signals from the AUX INPUT VIDEO jack. Video [...]

Connections En-21 This section explains how to connect the s upplied indoor FM antenna and AM loop antenna. The AV receiver won’t pick up any radio sign als without any antenna connected, so you mu st connect the antenna to use the tuner . Note • Once your AV receiver is ready for use, you’ ll need to tune into a radio station an d position t[...]

Connections En-22 With u (Remote Interactive), you can use the following special functions: ■ Auto Power On When you start playback on a component connected via u , while the AV receiver is on standby, the AV receiver will automa tically turn on and select that component as the input source. ■ Direct Change When playback is started on a compone[...]

En-23 Turning On & Basic Operations Turning On/Off the AV Receiver Tip •T h e HYBRID STANDBY indicator may light depending on the status of settings ( ➔ pa ge 59 ). • For details on power management settings, see “Auto Standby” ( ➔ page 81 ). 8 RECEIVER RECEIVER 8 ON/ST ANDBY Turning On 1 Press 8 ON/STANDBY on the front panel. or Pr[...]

Turning On & Basic Operations En-24 Initial Setup This section explains the se ttings that we recommend you to make before using the AV receiver for the very first time. A setup wizard is launc hed upon first-time use to let you perform those settings. This step determines the la nguage used for the onscreen setup menus. See “ Language ” in[...]

Turning On & Basic Operations En-25 This step checks the connection of source components. W ith this step, you can enter remote control codes for the components you want to operate. This step checks your network connection. This step ends the initial setup proc ess. Source Connection 1 Use q / w to select one of the following options, and then [...]

Turning On & Basic Operations En-26 Playback ■ Operating with the remote controller ■ Operating on the AV receiver The on-screen inform ation ap pears only on a TV that is connected to HDMI outputs. If your TV is connected to other vid eo outputs, use the AV receiver’s disp lay wh en changing settings. This section describ es the procedur[...]

Turning On & Basic Operations En-27 Tip • See “Controlling Other Components” about the operation of other components ( ➔ page 90 ). Note • The buttons you can use will diff er depending on the devices and media used for playback. Controlling Contents of USB or Network Devices k j m l n o h i q p e b a d f g c Press USB or NET first. a[...]

Turning On & Basic Operations En-28 This section describes ic ons that appear on the AV receiver’s display during media playback. This section explains how to play music/video files on the iPod/iPhone. Compatible iPod/iPhone models Made for: iPod touch (1st, 2nd, 3rd and 4t h generation), iPod classic, iPod nano (2nd, 3rd, 4th, 5th and 6th ge[...]

Turning On & Basic Operations En-29 Extended Mode (Music) Cont rol The music content informati on is displayed (lists are displayed), and you can control the music content while looking at the screen. Top screen list: Playlists, Artists, Albums, Genres, Songs, Composers, Shuffle Songs, Now Playing. Note • In this mode, video contents are not [...]

Turning On & Basic Operations En-30 Internet radio URLs in the followi ng formats are supported: PLS, M3U, and podcast (RSS). However, depending on the type of data or audio format used by the Internet radio station, you may no t be able to listen to some stations. To listen to other Internet ra dio stations, you must register your station in ?[...]

Turning On & Basic Operations En-31 The layout of icons can be cu stomized by switching their positions on the network service screen. This section explains how to play music file s on a computer or media server thr ough the AV receiver (Server Playback). Windows Media Playe r 11 Setup This section explains how to configure Windows Media Player[...]

Turning On & Basic Operations En-32 Remote Playback means you can play the music files stored on a media server or personal computer with the AV receiver by operating the controller device in the home network. Windows Media Player 12 Set up This section explains how to configure Windows Media Player 12 so that the AV receiver can play the music[...]

Turning On & Basic Operations En-33 This section explains how to play music files on a computer or NAS (Network A ttached Storage) through the AV receiver. Windows 7 Setup ■ Setting the sharing options ■ Creating a shared folder Playing music file s on a shared folder In order to enjoy Home Media, you must first create a shared folder on yo[...]

Turning On & Basic Operations En-34 Using the Tuner With the built-in tuner you can enjoy AM and FM radio stations. You can store your favor ite stations as presets for quick selection. You can also change the frequency steps ( ➔ page 79 ). Tuning into Radio Stations ■ Auto tuning mod e ■ Manual tunin g mode In manual tuning mode, FM st a[...]

Turning On & Basic Operations En-35 ■ Selecting Presets ■ Deleting Presets Listening to HD Radio™ Stations (North American models) HD Radio technology brings digi tal radio to conventional analog AM and FM radio st ations, with improved sound quality, better reception, a nd new data services. HD Radio technology provides CD-quali ty sound[...]

Turning On & Basic Operations En-36 ■ Setting the Blend Mode HD Radio transmissions contai n analog and digital signals. If available, the digital signal is used automat ically. In areas with poor reception, you may want to choose the analog signal. l Note • Multicast channels 2 through 8 are digital only, so you must select multicast chann[...]

Turning On & Basic Operations En-37 Note • In some cases, the text characters displayed on the AV receiver may not be identical to those b roadcast by the radio station. Also, unexpected characters may be displaye d when unsupported characters are received. This is not a malfunction. • If the signal from an RDS station is weak, RDS data may[...]

Turning On & Basic Operations En-38 You can listen to the audio of one input source while watching the video of anot her. Th is function takes advantage of the fact that wh en an audio-only input source ( TV/CD , PHONO ) is selected, the video input source remains unchanged. The foll owing procedure shows how to listen to a CD player’s audio [...]

Turning On & Basic Operations En-39 Using Basic Functions With the supplied calibrated microphone, Audyssey MultEQ ® XT32 automatically de termines the number of speakers connected, their size for purposes of bass management, optimum cro ssover frequencies to the subwoofer (if present), and distances from the primary listening position. Audyss[...]

Turning On & Basic Operations En-40 1 Turn on the AV receiver and the connected TV. On the TV, select the input to which the AV r eceiver is connected. 2 Set the speaker setup microphone at the Main Listening Position a , and connect it to the SETUP MIC jack. The speaker setting menu appears. Note • The on-screen menus appear on ly on a TV th[...]

Turning On & Basic Operations En-41 Note • You can cancel Audyssey MultEQ XT32 Room Correction and Speaker Setup at an y point in th is procedure simply by disconnecting the setup microph one. • Do not connect or disconnect any speakers during Audyssey MultEQ XT32 Room Corr ection and Speaker Setup. • If the AV receiver is muted, it will [...]

Turning On & Basic Operations En-42 Changing the Speaker Set up Manually You can manually make cha nges to the settings found during Audyssey MultEQ ® XT32 Room Correction and Speaker Setup. See also: • “Speaker Configuration” ( ➔ page 64 ) • “Speaker Distance ” ( ➔ page 65 ) • “Level Calibration” ( ➔ page 66 ) • “E[...]

Turning On & Basic Operations En-43 About Listenin g Modes The AV receiver’s listening modes can transform your listening room into a movie th eater or concert hall, with high fidelity and stunning surround sound. ■ Explanatory Notes ab Front speakers c Center speaker de Surround speakers f Subwoofer(s) gh Surround back speakers ij Front hi[...]

Turning On & Basic Operations En-44 *1 After enabling the corresponding spea kers, press RECEIVER followed by SP (speaker layout) repeatedly to select the speakers you want to use: front high , front wide, or surround back. *2 After enabling the corresponding spea kers, press RECEIVER followed by SP (speaker layout) repeat ed ly to select the l[...]

Turning On & Basic Operations En-45 ■ Onkyo-Original DSP Listening Modes Listeni ng Mode Description Input Source Speaker Layout Orchestra Suitable for classical or operatic music, this mode emphasizes the sur round channels in order to widen the stereo image, and simulates the natural reverberation of a large hall. A S D F G H cnm Unplugged [...]

Turning On & Basic Operations En-46 ■ Listening Modes Listeni ng Mode Description Input Source Speaker Layout Pure Au dio *1 In this mode, the display and video circuitry are turned off, minim izing possible noise sources for the ulti mate in high-fidelity audio reproduction. (As the analog video circuitry is turned off, on ly video signals i[...]

Turning On & Basic Operations En-47 Dolby Pro Logic IIx *7 Dolby Pro Logic II Dolby Pro Logic IIx expands any 2-channel source for 7.1-channel playback. It prov ides a very natural and seamless surround- sound experience that fully envelops the listener. As well as music and movies, video games can also benefit from the dramatic spatial effects[...]

Turning On & Basic Operations En-48 • Dolby Pro Logic II/IIx *7 Movie + Audyssey DSX • Dolby Pro Logic II/IIx *7 Music + Audyssey DSX • Dolby Pro Logic II/IIx *7 Game + Audyssey DSX The combination of Dolby Pro Logic II/IIx and Audyssey DSX ® modes can be used. S. /m • Dolby Pro Logic IIx Movie + Audyssey DSX • Dolby Pro Logic IIx Mu[...]

Turning On & Basic Operations En-49 Note *1 Pure Audio cannot be selected when Z one 2/3 is active. Besides, if you activate Zone 2/3 while Pure Audio i s selected, the listening mode will automatically switch to Direct. *2 Based on the audio channel signal contained in the source, the correspond ing speakers will output the sound. *3 The AV re[...]

Turning On & Basic Operations En-50 The Home menu provides quick access to frequently used menus. ■ Network Service ` With this selecti on, you can use various Internet radio services or play the contents sto red in media connected to your home network (DLNA) ( ➔ pages 29 to 32 ). Note that this selection will be grayed out for a short whil[...]

Turning On & Basic Operations En-51 With the sleep timer, you can set the AV receiver to turn off automatically aft er a specified period. You can adjust the brightness of the AV receiver’s display, and switch the MASTER VOLUME indicator off and on in conjunction. You can display various info rmation about the current input source as follows.[...]

Turning On & Basic Operations En-52 The Whole House Mode is us ef ul when you want to add extra background music to your home party; this allows you to enjoy the same stereo music as the main room in separate rooms (Zone 2/3). The Whole House Mode selects the same input source for Multi Zone as the main room’s. See also: • “Speaker Setup?[...]

Turning On & Basic Operations En-53 By using ACTIVITIES in Easy macro mode, you can sequentially operate Onkyo components via simple commands from a single-button press. These commands are user-definable. See “Us ing Normal Macros” ( ➔ page 96 ). ■ MY MOVIE First, the TV, the Onkyo Blu-ray Dis c player, an d the AV receiver are turned o[...]

En-54 Advanced Operations On-screen Setup With the AV receiver connected to a TV, there are two ways of changing the settings on-screen: using the Quick Setup or the Setup menu ( HOME ). ■ Quick Setup The Quick Setup provides quick access to frequently used settings. You can change sett ings and view the current information. ■ Setup menu (HOME)[...]

Advanced Operations En-55 ■ Listening Mode *7 ` You can select the listening modes that are grouped in the following categories: “ MOVIE/TV ”, “ MUSIC ”, “ GAME ”, and “ THX ”. Use q / w to select the category an d e / r to select the listening mode. Press ENTER to switch to the selected listening mode. Note *1 • The video previ[...]

Advanced Operations En-56 Speaker Leve ls ■ Subwoofer 1 ` –15.0dB to 0.0dB to +12.0dB in 0.5 dB steps. ■ Subwoofer 2 *1 ` –15.0dB to 0.0dB to +12.0dB in 0.5 dB steps. ■ Center ` –12.0dB to 0.0dB to +12.0dB in 0.5 dB steps. You can adjust the volume of each speaker while listening to an input source. These temporary adjust ments are canc[...]

Advanced Operations En-57 Music Opti mizer ■ Music Optimizer ` Off ` On The Music Optimizer function enhances the sound quality of compressed music files. When se t to “ On ”, the M.Opt indicator lights on the AV receiver’s display. Note • The Music Optimizer function only works with PCM digital audio input signals with a sampling rate be[...]

Advanced Operations En-58 Note • This procedure can also be performed on the AV receiver by using SETUP , the cursor and enter (middle) buttons. • During Audys sey MultEQ ® XT32 Room Correction and Speaker Setup, messages, etc., that are displaye d on the TV screen will appear on the AV rece iver’s display. Explanatory Notes a Main Menu b Su[...]

Advanced Operations En-59 By way of optimized circuitry, this fu nction reduces power consumption when the AV rece iver is in standby mode. The HYBRID STANDBY indicator will li ght in either of the following conditions: –“ HDMI Th rough ” is enabled (the HDMI indicator is off). –“ Network Standby ” is enabled (the NE T indicator is off)[...]

Advanced Operations En-60 Main Menu Input/Output Assi gn Monitor Out On the “ Monitor Out ” settings, you can se lect whether or not to hav e the video sour ces’ images output through the HDMI output. If you connect your TV to the HDMI output, the “ Monitor Out ” setting is automatically set and composite video and component video sources[...]

Advanced Operations En-61 You can specify the output resolution f or HDMI OUT MAIN and COMPONENT VIDEO MONITOR OUT so that the AV receive r upconverts the picture resolution as necessary to match the resolution suppo rted by your TV. Tip • You can see the picture by pressing ENTER to check the “ Resolution ” setting for HDMI OUT MAIN (excludi[...]

Advanced Operations En-62 • If you assign “ ----- ” to an input selector that is curre ntly selected in “ HDMI Through ” ( ➔ page 80 ), the “ HDMI Through ” setting will be automatically switched to “ Off ”. •“ AUX ” is used only for input from the front panel. Component Video Input If you connect a video compone nt to a c[...]

Advanced Operations En-63 Digital Audio Input If you connect a component to a digital audio input, you must assign that input to an i nput selector. For example, if you connect your CD player to the OPTICAL IN 1 , you must assign “ OPTICAL1 ” to the “ TV/CD ” input selector. Here are the d efault assignments. ■ BD/DVD , CBL/SAT , STB/DVR,[...]

Advanced Operations En-64 ■ Preout to External Amplifi er ` No ` Surr Back , Front High , Front Wide For 9.2-channel playback, se lect the channel output by SB/FH/FW EXT AMP jacks. I f you sel ect speakers whose setting in Speaker Configuration is set to “ None ”, it will be automatically swi tched to “ 80Hz (THX) ”. Note • If the “ S[...]

Advanced Operations En-65 ■ Surround Back Ch ` 1ch : Select if only one surround back speaker L is connected. ` 2ch : Select if two (left and right) surro und back speakers are connected. Note • If the “ Surround Back ” setting is set t o “ None ”, this setting cannot be selected. ■ LPF of LFE (Low-Pass Filter fo r the LF E Channel) `[...]

Advanced Operations En-66 Level Calibration Here you can adjust the leve l of each speaker with the built-in test tone so that the volume of each speaker is the same at the listening position. ■ Left, Front Wide Left, Front High Left, Center *1 , Front High Right, Fr ont Wide Right, Right, Surround Right, Su rround Back Right, Su rround Back Left[...]

Advanced Operations En-67 ■ Loudness Plus ` Off ` On When the “ Loudness Plus ” setting is set to “ On ”, it is possible to enjoy even subtle nuances o f audio expression at low volume. This is only available when the THX listening mode is selected. ■ Preserve THX Settings ` Yes ` No If this setting is set to “ Yes ”, Dy namic EQ, D[...]

Advanced Operations En-68 ■ Overlap ` No ` Yes With this setting, a freque ncy band near the specified crossover frequency is out put by both tweeters and woofers. Based on the frequency selected for “ Crossover ”, the cutoff frequency of the low-pa ss filter (LPF) will be set to 1/3 octave up and that of the high-pass filter (HPF) to 1/3 oct[...]

Advanced Operations En-69 Output Speaker ` Center : Mono audio is output by the center speaker. ` Left / Right : Mono audio is output by th e front left and right speakers. This setting de termines whic h speakers output mono audio when the Mono listeni ng mode is selected. Note • If the “ Center ” setting is set to “ None ” ( ➔ page 64[...]

Advanced Operations En-70 ■ Dolby Volume ` Off ` On Dolby Volume automatical ly adjusts the difference in volume levels which can occur between differe nt contents or source components, freeing the user from having to make volume adjustments. Also, by adjusting the frequency balance according to the playback volume, it recreates the original s ou[...]

Advanced Operations En-71 Audyssey DSX ® ■ Soundstage ` –3dB to Reference to +3dB With this setting, you can ad just the sound stage when using Audyssey DSX. Note • This listening mode can be select ed only when a ll the following conditions are satisfied: – T he center speaker is connected. – Either the front high or front wide speakers[...]

Advanced Operations En-72 ■ Equalizer *1 ` Off ` Manual : The manual setting in “Equalize r Settings” ( ➔ page 66 ) is applied. ■ Audyssey *1 ` Off , Movie , Music See “Audyssey” ( ➔ page 56 ). ■ Dynamic EQ *1*2 ` Off , On See “Dynamic EQ ” ( ➔ page 56 ). ■ Dynamic Volume *1*2 ` Off , Light , Medium , Heavy See “Dynamic [...]

Advanced Operations En-73 Movies are mixed in rooms ca lib rated for film reference. To achieve the same referenc e level in a home theater system each speaker level must be adjusted so that –30 dBFS band-limited (500 Hz to 2000 Hz) pink noise produces 75 dB sound pressure level at the listening position. A home t heater system aut omatically ca [...]

Advanced Operations En-74 Name Edit You can enter a custom name for each individual in put selector and radio preset for easy identifi cation. When entered, the custom name will app ear on the display. The custom name is edited using the keyboard screen. ■ Name Tip • To name a radio preset, use TUNER to select A M or FM , and then select the pr[...]

Advanced Operations En-75 ■ Picture Mode *1*3 ` Custom : All settings can be performed manually. ` ISF Day : Select when the room is bright. ` ISF Night : Select when the room is dark. ` Cinema : Select when the picture source is a mov ie or alike. ` Game : Select when t he video s ource is a game console. ` Streaming : Attempts to reduce the mo [...]

Advanced Operations En-76 ■ Resolution *4*6*8* 9*10 ` Through : Select this to pass video through the AV receiver at the same resolution and with no conversion. ` Auto : Select this to have the AV receiver automat ically convert video at resolutions supported by your TV. ` 480p ( 480p/576p ), 720p , 1080i , 1080p : Select the desired output resol[...]

Advanced Operations En-77 Audio Selector ■ Audio Selector ` ARC : The audio signal from your TV tuner can be sent to HDMI OUT MAIN of the AV receiver. *1 With this selection, the TV’s audio can be automatically selected as a priority among other assignments. ` HDMI : This can be selected when HDMI IN has been assigned as an input source. If bot[...]

Advanced Operations En-78 ■ Analog/PCM/Digital With this setting, you can specify the listening mode used when an analog (CD, TV, LD, VHS, MD, turntable, radio, cassette, cable, satellit e, etc.) or PCM digital (CD, DVD, etc.) audio signal is played. Note •F o r t h e “ GAME2 ” input selector, only “ PC M ” is available. ■ Mono/Multip[...]

Advanced Operations En-79 OSD Setup ■ On Screen Display ` On ` Off This preference determines whether operation details are displayed on-screen when an AV receiver function is adjusted. Even when “ On ” is selected, opera ti on details may not be output if the input source is connected to an HDMI IN . ■ Language (North Americ an models) ` E[...]

Advanced Operations En-80 ■ HDMI Through ` Off ` BD/DVD , CBL/SAT , STB/DVR , GAME1 , GAME2 , PC , AUX , TV/CD , PHONO : Selects the input source for which the HDMI Through function is enabled. ` Last : The HDMI Through function is activated on the input source selected at th e time of setting the AV receiver to standby mode. When enabling the HD[...]

Advanced Operations En-81 ■ InstaPrevue These settings apply to “ InstaPrev ue ” of the Home menu ( ➔ page 50 ) and specify the preview display of HDMI video streams. Sub Window ` Multi : Displays preview thum bnails all at once. ` Single : Displays preview thumbnails one-by-one. With this setting, you can set th e number of preview thumbna[...]

Advanced Operations En-82 ■ Gateway Enter the gateway address provided by your ISP. ■ DNS Server Enter the DNS server address provided by your ISP. ■ Proxy URL To use a Web proxy, enter its URL here. ■ Proxy Port If you’re using a Web proxy, enter a proxy port number here. ■ Network Standby ` On ` Off This setting enables or disa bles c[...]

Advanced Operations En-83 Multi Zone In addition to the main liste ning room, you can also enjoy playback in the other room, or as we call Multi Zone. And, you can select a different source for each room. There are two ways you ca n connect Zone speakers: 1. Connect them directly to the AV receiver. 2. Connect them to an additional amplifier. Conne[...]

Advanced Operations En-84 Connecting the Zone Speaker s to an Additional Amplifier This setup allows 7.2-cha nnel playback in your main listening room and 2-channel stereo playback in Zone 2/3. Note • The volume of Zone 2/3 must be set on the Zone 2/3 amplifier. 12V Trigger Ou t When Zone 2/3 is turned on, the output from the 12V TRIGGER OUT jack[...]

Advanced Operations En-85 ■ Operating on the AV receiver Tip • The Whole House Mode function shar es the input source of main room with Multi Zone ( ➔ pag e 52 ). ■ Operating on the remote controller To control Zone 2/3, you must press ZO NE on the remote controller first. ZONE turns red when Zone 2 is on, and green when Zone 3 is on. Adjus[...]

Advanced Operations En-86 Muting Zones ■ Operating on the remote controller Tip • To unmute, pr ess ZONE followed by MUTING again. Zones can also be unmute d by adjusting the volume. Note • ZONE 2 LINE OUT and FRONT WIDE /ZONE 2 L/R output 2ch PCM and analog input sources. To listen to the PCM source, you need to make an HDMI connection ( ➔[...]

Advanced Operations En-87 Using a Multiroom Kit with a Cabinet In this setup, the IR receiver picks up the infra red signals from the remote controller and feeds them to the AV receiver located in the cabi net via the connecting block. Using a Multiroom Kit with Other Components In this setup, an IR emitter is connected to the AV receiver’s IR OU[...]

En-88 Controlling Other Components iPod/iPhone Playback via Onkyo Dock RI Dock With the RI Dock, you can easily play the music of your iPod/iPhone, or watch the slid eshows and videos of your iPod/iPhone on a TV. In addition, the on-screen display (OSD) allows you to view, navigate, and select your iPod/iPhone model’s contents on your TV, and wit[...]

Controlling Other Components En-89 By pressing the REMOTE MODE button that’s been programmed with the remote control code for your Dock, you can control your iPod/iPhone in the Dock with the buttons described further in this section. See “Entering Remote Control Codes” for details on entering a remote control code ( ➔ page 91 ). See the Doc[...]

Controlling Other Components En-90 Controlling Other Components You can use the AV receiver’s remot e controller to cont rol your other AV components, in cluding those made by other manufacturers. This secti on explains how to enter the remote control code for a component th at you want to control: DVD, TV, CD, etc. See “Learning Commands ” f[...]

Controlling Other Components En-91 You’ll need to enter a code for each component that you want to control. Note • Though the prov ided remote cont rol codes are correct at the time of release, they are subject to change. You can change the configuration of colored b uttons, with which REMOTE MODE buttons are preset. Tip • To reset the REMOTE[...]

Controlling Other Components En-92 Onkyo components that are connected via u are controlled by pointing the re mote controller at the AV receiver, not the component. This allows you to control components that are out of view, in a rack, for example. Controlling Onkyo co mponents without u If you want to control an Onkyo component by pointing the re[...]

Controlling Other Components En-93 Controlling MHL-Enabled Mobile De vice By programming the supplied re mote controller with the appropriate remote control code, you can use it to operate your MHL-enabled mobile device. Connect your MHL-enabled mobile device to the AUX INPUT MHL jack. We advise you to program the remote control code on the AUX but[...]

Controlling Other Components En-94 ■ DVD player/DVD reco rder operation ■ VCR/PVR operation ■ Cassette tape deck operation ■ Satellite receiver/Cable receiver oper ation ■ CD player/CD recorder/MD recorder operation Note • With some components, certain buttons may not work as expected, and some may not work at all. • See “Controllin[...]

Controlling Other Components En-95 The AV receiver’s remote controller can lear n the commands of other remote con trollers. By transmittin g, for example, the Play command fro m your CD player’s remote controller, the supplied remote controller can learn it and then reproduce the exact sam e command when its 1 is pressed in CD remote mode. Thi[...]

Controlling Other Components En-96 You can program the re mote controller’s ACTIVITIES to perform a sequence of re mote control actions. Example: To play a CD you typically need to perform the following actions: 1. Press RECEIVER to sele ct the Receiver rem ote controller mode. 2. Press 8 RECEIVER to turn on the AV receiver. 3. Press TV/CD to sel[...]

En-97 Appendix Troubleshooting If you have any trouble using th e AV receiver, look for a solution in this section. If you can’t resolve the issue yourself, contact your Onkyo dealer. ■ Can’t turn on the AV receiver ■ The AV receiver turns off unexpectedly ■ The AV receiver turns o ff and after restoring the power, it turns off again ■ [...]

Appendix En-98 ■ Only the front speakers produce sound ■ Only the center sp eaker produces sound ■ The surround speakers produce no sound ■ The center speaker produces no sound ■ The front high, front wi de and surround back speakers produce no sound ■ The subwoofer pr oduces no sound ■ There’s no sound w ith a certain signal format[...]

Appendix En-99 ■ About DTS signals ■ The beginning of audio received by an HDMI IN can’t be hea rd ■ There’s no sou nd during Whole Hou se Mode ■ There’s no picture ■ There’s no picture from a source connected to an HDMI IN ■ The on-screen me nus don’t app ear ■ The on-screen informa tion does not appear ■ Reception is noi[...]

Appendix En-100 ■ The remote contro ller do esn’t work ■ Can’t control oth er components ■ Can’t learn commands from another remote controller ■ There’s no sound ■ There’s no video ■ The AV receiver’s remo te controller doesn’t control my iPod/i Phone ■ The AV receiver unexp ectedly selec ts my iPod/iPhone as the in put [...]

Appendix En-101 ■ There’s no sound ■ The Zone 2/3 speaker s produce no sound ■ Can’t access the server or Internet radio ■ Playback stops while listen ing to music files on the server ■ Can’t connect to the AV receiver from a Web browser ■ Can’t access the music files on a USB device ■ Standby power consumptio n ■ The sound [...]

Appendix En-102 ■ When performi ng Automa tic Speaker Setup, the measurement fails and the message “Ambie nt noise is too high .” is displayed. ■ The following setti ngs can be made for the composite video inputs You must use the buttons on the unit to make these settings. On the AV receiver, press the input selector for the input source th[...]

Appendix En-103 Firmware Update To update the firmware of the AV receiver, you can choose from the following two methods: update via network, or update via USB storage. Choose the one that best suits your environment. Before pr oceeding with the update, please read the correspondi ng explanations carefully. ■ Update via network You need a wired I[...]

Appendix En-104 Update Procedure Troubleshooting Case 1: If an error occurs, “ Error!! *-** ” is displayed on the AV receiver’s display. (Alpha-num eric characters on the front display are denoted by asterisk s.) Refer to the following table and take a ppropriate action. ■ Errors during an update via netwo rk Case 2: If an error occurs duri[...]

Appendix En-105 The AV receiver allows you to update the firmware using a USB device. Note • Never unplug or turn off the AV receiver duri ng the update process. • Never plug or unplug an HDMI cable o r a USB device during the update process. • Never unpl ug the USB stor age device containi ng the firmware file or the AC power cord during the[...]

Appendix En-106 Troubleshooting Case 1: If an error occurs, “ Error!! *-** ” is displayed on the AV receiver’s display. (Alpha-numeric ch aracters on the front display are denoted by asterisk s.) Refer to the following table and take appropriate action. ■ Errors during an update via USB Case 2: If an error occurs during the update process, [...]

Appendix En-107 Connection Tips and Video Signal Path The AV receiver supports seve ral connection formats for compatibility with a wi de ra nge of AV equipment. The format you choose will depe nd on the formats supported by your components. Use the foll owing sections as a guide. Video components can be c onnected by using any one of the following[...]

Appendix En-108 ■ “Monitor Out” set to “Analog” Video input signals flow through the AV receiver as shown, with composite vide o and PC IN (Analog RGB) sources being upconverted for the component video output. Use this setting if you conne ct the AV receiver’s COMPONENT VIDEO MONITOR OUT to your TV. The composite video and co mponent vi[...]

Appendix En-109 Audio components can be conne cted by using any o f the following audio c onnection formats: analog, optical, coaxial, or HDMI. When choosing a connection form at, bear in mind that the AV receiver does not convert digital input signals for analog line outputs and vice v ersa. If signals are present at more than one input, the input[...]

Appendix En-110 The following tables show how vide o signals at differe nt resolutions are output by the AV receiver. NTSC/PAL ✔ : Output available s *1 Available resolutions: [640 × 480 60 Hz], [800 × 600 60 Hz], [1024 × 768 60 Hz], [1280 × 1024 60 Hz] *2 Supported resolutions: [3840 × 216 0 24/25/30 Hz], [4096 × 2160 24 Hz] *3 When video [...]

Appendix En-111 Using an RIHD- compatible TV, Player, or Recorder p , which stands for Re mote Interactiv e over HDMI, is the name of the system control function found on Onkyo components. The AV rece iver can be used with CEC (Consumer Elec tronics Control), which allows system control over HDMI and is part of the HDMI standard. CEC provides inter[...]

Appendix En-112 ■ How to connect and setup 1 Confirm the connection and s ettings. 1. Connect the HDMI OUT MAIN jack to the HDMI input jack of the TV. 2. Connect the audio output from the TV to the OPTICAL IN 2 jack of the AV receiver using an optical digital cable. Note • When the audio return channel (ARC) function is used with an ARC capable[...]

Appendix En-113 About HDMI Designed to meet the increa sed demands of di gital TV, HDMI (High Definition Multimedia Interfac e) is a new digital interface standard fo r co nnecting TVs, projectors, Blu-ray Disc/DVD players, se t-top boxes, and other video components. Until now, severa l separate video and audio cables have been required to connect [...]

Appendix En-114 Network/USB Features The following diagram shows how you can connect the AV receiver to your home network. In this example, it’s connected to a LAN port on a router, which has a 4-port 100Base-TX switch built-in. ■ Ethernet Networ k For the best results, a 100B ase-TX switched Ethernet network is recommended. Although it’s pos[...]

Appendix En-115 ■ Server playback The AV receiver ca n play digital music files stored on a computer or media server and supports the following technologies: • Windows Media Player 11 • Windows Media Player 12 • Windows Media Connect 2.0 • DLNA-certified media server If the operating system of your computer is Windows Vista, Windows Media[...]

Appendix En-116 For server playback and pla yback from a USB device, the AV receiver supports the fo llowing music file formats. Variable bit-rate (VBR) file s are supported. However, playback times may not display correctly. Note • With remote playback, the AV receiver does not support the following music file formats: FLAC, Ogg Vorbis, DSD and [...]

Appendix En-117 License and Trademark Information “x.v.Color” is a trademark of Sony Corporation. Manufactured under license und er U.S. Patent No’s: 5,956,674; 5,974,380; 5, 978,762; 6,487 ,535; 6,226, 616; 7,212,872 ; 7,003,467; 7, 272,567; 7,668 ,723; 7,392, 195; 7,930,184 ; 7,333,929; 7, 548,853; 7,283,6 34 & other U.S. and worl dwide[...]

Appendix En-118 Specifications Amplifie r Section Video Section Tuner Section General ■ HDMI ■ Video Inputs ■ Video Outputs ■ Audio Inputs ■ Audio Outputs ■ Others Specifications and featu res are subject to change without notice. Rated Output Power All channel s: (North Am erican) 140 watts mini mum continuous power per channel, 8 oh m[...]

Appendix En-119 Memo[...]

2-1, Nisshin-cho , Ney aga wa-shi, OSAKA 572-8540, J AP AN T el: 072-831-8023 F ax: 072-831-8163 http://www .onkyo .com/ 18 P ark W a y , Upper Saddle River , N.J . 07458, U.S .A. T el: 800-229-1687, 201-785-2600 F ax: 201-785-2650 http://www .us.onkyo .com/ Liegnitzerstrasse 6, 82194 Groebenz ell, GERMANY T el: +49-8142-4401-0 F ax: +49-8142-4208-[...]

Using Internet Radio En-1 Using Internet Radio Note • Available services may vary depending on the r egion. Common Procedures in Internet Radio Menu 1 Press NET . A list of the network serv ices appears, and the NET indicator lights. If it flashe s, verify that the Ethernet cable is firmly connected to the AV receiver. 2 Select the des ired servi[...]

Using Internet Radio En-2 Pandora is a free, personalized Internet radio service that plays the music you know and helps you discover music you’ll love. PANDORA, the PANDORA logo, and the Pandora trade dress are trademarks or regi stered trademarks of Pandora Media, Inc. Used with permission. Pandora ® internet radio –Getting Started (U.S. onl[...]

Using Internet Radio En-3 Using Rhapsody (U.S. only) 1 Use q / w to select “Sign in to your account” and then press ENTER . To use Rhapsody, you need an acco unt. If you don’t have one yet, you can create a new account at www.rhapsody.com/onkyo If you have an existing Rhapsody account, select “ Sign in to your account ” and press ENTER . [...]

Using Internet Radio En-4 Your Onkyo AV receiver includes a free trial of SiriusXM Internet Radio. The “Account Info” screen shows how many days are left in your trial. After the trial period expires, if you want to conti nue listening to the service, you must subscribe. To subscribe go to www.siriusxm.com /internetradio with your computer. Whe[...]

Using Internet Radio En-5 Last.fm is a music s ervice th at learns what you love... Your new Onkyo AV receiver is very clever. If you have a free Last.fm account, it will keep track of all the songs you’ve just played. When you visit the Last.fm website, you can see personal charts of the music you’ve enjoyed, share them with friends and see wh[...]

Using Internet Radio En-6 Using Slacker Personal Radio 1 If you do not have an ac count, create one on the Slacker website (www.sl acker.com) with your computer. If you already have a Slac ker account, se lect “Sign in to your account” and then press ENTER . The keyboard screen appears. You can enter information from the remote control or the k[...]

Using Internet Radio En-7 Listen to your music collection on your home stereo in complete digital fide lity wit hout a p ersonal computer plus safely backup all your songs. Here’s how: Creating an Account on your Computer Playing Contents on the AV Receiver Tip • Before proceeding, you need to select the MP3tunes service as described in “Com [...]

Utilisation d’une webradio Fr-1 Utilisation d’une webradio Remarque • Les services disponibles peuvent varier en fonction de la région. Procédures courantes dans le menu de webradio 1 Appuyez sur NET . Une liste des services réseau s’affiche, et le témoin NET s’allume. S’il clignote , vérifiez que le câble Ethernet est f ermement [...]

Utilisation d’une webradio Fr-2 Pandora est un service de radio en ligne libre et personnalisé vous permettant de lire la musique que vous connaissez et de découvrir celle que vous aimez. PANDORA, le logo PANDOR A, et l’habillage commercial Pandora sont des marques commerciales ou des marques dépo sées de la société Pandora Media, Inc. Ut[...]

Utilisation d’une webradio Fr-3 Utilisation de Rhapsody (Etats-Unis uniquement) 1 Utilisez q / w pour sélec tionner « Sign in to your account », puis appuyez sur ENTER . Vous devez posséder un compte pour utiliser Rhapsody. Si vous ne di sposez pas encore d’un compte, vous pouvez en créer un à partir de www.rhapsody.com/onkyo Si vous poss[...]

Utilisation d’une webradio Fr-4 Votre ampli-tuner AV Onkyo co mprend un essai gratuit de SiriusXM Internet Radio. L’ écran « Account Info » affiche le nombre de jours restants da ns votre essai. Une fois la période d’essai expirée, si vous souhaitez continuer à écouter le service, vous de vez vous abonner. Pour vous inscrire, accé dez[...]

Utilisation d’une webradio Fr-5 Last.fm un service de musique qui appr end ce que vous aimez… Votre nouvel ampli-tuner AV O nkyo est très intelligent. Si vous avez un compte Last.fm gr atuit, il garde une trace de toutes les chansons que vous avez juste jouées. Quand vous vous rendez sur le site Web de Last.fm, vous pouvez voir les graphiques[...]

Utilisation d’une webradio Fr-6 Utilisation de Slacker Personal Radio 1 Si vous ne possédez pas de compte, c réez-en un à partir du site Web de Slacker (www.slacker.com) à l’aide de votre ordinateur. Si vous possédez déjà un compte Slacker, sélectionnez « Sign in to your account », puis appuyez sur ENTER . L’écran clavier s’affic[...]

Uso de In ternet Radio Es-1 Uso de Internet Radio Nota • Los servicios disponibles pueden variar de una regió n a otra. Procedimientos comunes en el menú Internet Radio 1 Pulse NET . Aparecerá una lista de los servicios de red y se iluminará el indicador NET . Si parpadea, verifique que el cable Ethernet esté firmem ente conectado al recepto[...]

Uso de In ternet Radio Es-2 Pandora es un servicio de radi o por Internet gratuito y personalizado que reproduce la música que usted conoce y le ayudará a descubrir mú sica que le encantará. PANDORA, el logotipo de PANDORA logo, y la imagen corporativa de Pandora son ma rcas comer ciales o marcas comerciales registradas de Pandora Media, Inc. U[...]

Uso de In ternet Radio Es-3 Uso de Rhapsody (sólo EE.UU.) 1 Utilice q / w para sel eccionar “Sig n in to your account” y luego pulse ENTER . Para utilizar Rhapsod y, necesitará una cuenta . Si todavía no tiene una, puede crear una nueva en www.rhapsody.com/onkyo Si ya tiene una cuenta Rhapsody, seleccione “ Sign in to your account ” y pu[...]

Uso de In ternet Radio Es-4 Su receptor de AV Onkyo incl uye una prueba gratuita de SiriusXM Internet Radio. La pantalla “Account Info” muestra los días que quedan de la prueba. Una vez que termine el periodo de prueba, si desea seguir escuchando este servicio, deberá contrata rlo. para suscribirse vaya a www.siriusxm.com /internetradio con s[...]

Uso de In ternet Radio Es-5 Last.fm es un servicio musica l que sabe lo que le gusta... Su nuevo receptor de AV O nkyo es muy inte ligente. Si tiene una cuenta gratuita de Last.fm, hará un seguimiento de todas las canciones que acaba de escuchar. Cuando visite el sitio web de Last.fm, podrá ver listas personales de la música que ha disfrutado, c[...]

Uso de In ternet Radio Es-6 Uso de Slacker Personal Radio 1 Si no tiene una cuenta, cree una en el sitio web de Slacker (www.slacker.co m) con su ordenador. Si ya tiene una cuenta d e Slacker, seleccione “Sign in to your account” y pulse ENTER . Aparecerá la pantal la de teclado. Puede introducir información desde el man do a distancia o desd[...]

SN 29401189B (C) Copyright 2012 Onkyo Sound & Vision Cor poration Japan. All rights reser ved. Y1203-2 * 2 9 4 0 1 1 8 9 B *[...]

En-1 Using Internet Radio Using Internet Radio Note • Available services may vary depending on the r egion. Common Procedures in Internet Radio Menu 1 Press NET . A list of the network serv ices appears, and the NET indicator lights. If it flashe s, verify that the Ethernet cable is firmly connected to the AV receiver. 2 Select the des ired servi[...]

Using Internet Radio En-2 Last.fm is a music s ervice th at learns what you love... Your new Onkyo AV receiver is very clever. If you have a free Last.fm account, it will keep track of all the songs you’ve just played. When you visit the Last.fm website, you can see personal charts of the music you’ve enjoyed, share them with friends and see wh[...]

Internetradio verwenden De-1 Internetradio verwenden Anmerkung • Die verfügbaren Dienste sind länderab hängig verschieden. Allgemeine Verfahren bei den Internetradio-Me nüs 1 Drücken Sie NET . Es erscheint eine Liste der Netzwerkdienste und die NET -Anzeige leucht et. Wenn sie bli nkt, überprüfen Sie ob das Ethernet-Kabel fest im AV-Receiv[...]

Internetradio verwenden Last.fm ist ein Musikdiens t, der sich Ihre Lieblingsmusik merkt... Ihr neuer Onkyo AV-Receiver ist äußer st clever. Wenn Sie ein kostenloses Last.fm-Konto ei ngerichtet haben, werden darin all e kürzlich abgespiel ten Titel gesp eichert. Wenn Sie die Last.fm- Website besuchen, können Sie Ihre persönl ichen Charts der v[...]

Remote Co ntrol Codes 1 Remote Control Codes / 1 While holding d own the REMOTE MO DE bu tton to which you want to assign a code, press and hold down [DISPLAY] (about 3 seconds). The REMOTE MODE button/ Remote indicator lights. On Integra products, button names are ca pitalized. For example , “Remote Mode” button and “Display” button. Notes[...]

Remote Co ntrol Codes 2 Codes de télécommande Códigos de control remoto 1 Tout en maintenant enfoncé le bouton REMOTE MODE auquel vous souhaitez associer un code, pressez et maintenez enfoncé le bou ton [DISPLAY] (pendant environ 3 secondes). Le bouton REMOTE MODE/le témoin Remote s’allume. Les noms de boutons sont en manjuscules su r les p[...]

Remote Co ntrol Codes 3 Codici del telecomando Fernbedienungscodes 1 Tenendo premuto il tasto REMOTE MODE al quale si desid e ra assegnare il codice, premer e e tenere premut o [DISPLAY] (per circa 3 secon di). Il tasto REMOTE MODE/l'indi catore Remote si acce nde. Sui prodotti Integra, i nomi dei tasti sono scri tti con l'iniziale maiu s[...]

Remote Co ntrol Codes 4 Afstandsbedieningscod es Fjärrstyrningskoder 1 Houd terwijl u de REMOTE MODE toets ingedrukt houdt waarvoor u een code wilt toewijzen de [DISPLAY] toet s ingedrukt (ongeveer 3 seconden). De toets REMOTE MODE (afstandsbed ieningsmodus) / Het indicatielampje afstandsbediening gaat branden. Op producten van Integra staan de na[...]

Remote Co ntrol Codes 5 遙控代碼 遥控代码 1 在按住想指定編碼的 REMOTE MODE （遙控模式）按鈕時，同時按住 [DISPLAY] （顯示） （約 3 秒） 。 REMOTE MODE （遙控模式）按鈕 / 遙控指示燈亮起。 在 Integra 系列產品上， 按鈕名稱為大寫。 例如， 「Remote Mode」 （遙控模式） 按?[...]

Remote Co ntrol Codes 6 Dedicated On kyo Receiver Default 62503 Zone 2 62506 Zone 3 62507 Cable Set T op Box ADB 02254, 02769 Aon 02769 Arris 02187 AT&T 00858 Bright House 01376, 01877 BT Vision 02294 Cable & Wireless 01068 Cable One 01376, 01877 Cablecom 015 82 Cablevision 01376, 0187 7 Charter 01376, 01877, 02187 Cisco 01877, 0085 8, 0198[...]

Remote Co ntrol Codes 7 AT&T 00858 BT Vision 02294 Cisco 00858, 0234 5, 02378 Kreatel 01385 Motorola 00858, 02378 Neuf TV 03107 Philips 02294 Scientific Atlanta 00858 SFR 03107 Verizon 0237 8 CD Advantage 70032 AH! 70157 Aiwa 70157 Arcam 70157 Atoll Electronique 70157 Audio Research 70157 Audiolab 70157 Audiomeca 70157 Audioton 70157 AVI 70157 [...]

Remote Co ntrol Codes 8 Polk Audio 82228 Video - Accessory ADB 02254, 02769 Aon 02769 Apple 02615 AT&T 00858 BT Vision 02294 Canal+ 02657 Cisco 00858, 0234 5, 02378 Kreatel 01385 mio TV 02802 Motorola 01376, 00858, 019 98, 02378 Neuf TV 03107 Pace 02657 Philips 02294 Scientific Atlanta 00858, 02345 SFR 03107 SingTel 0199 8, 02802 TeliaSonera 01[...]

Remote Co ntrol Codes 9 Hama 01567 Hanseatic 01100 Hirschmann 00173 Hitachi 01284 Hornet 01300 HTS 00775 Humax 01377, 01176, 014 27, 01675, 0180 8, 01882, 01915, 0214 4, 02408, 02616 ID Digital 01176 ID Sat 01334 ILLUSION sat 0163 1 Imperial 0 1195, 01334 Indovisio n 00887 iNETBOX 01237 Inno Hit 01626 Innova 00099 inVion 02418 iotronic 01413 ISkyB [...]

Remote Co ntrol Codes 10 Star 00887 Stream System 01300 Strong 00853, 0 0879, 01284, 01300, 0140 9, 01626, 02418 Sunny 01300 Sunstar 00642 Supernova 00887 Supratech 01413 Systec 01334 Sytech 02418 TBoston 0125 1, 02418 Teac 01251 Technical 01626 Technika 01284 TechniSat 0 1100, 01195 Technosat 01206 Techwood 01251, 0 1284, 016 26 TELE System 0 1251[...]

Remote Co ntrol Codes 11 Akai 10178, 10556, 10037, 10714, 1071 5, 10208, 11675 Akiba 10037 Akito 10037 Akura 10171, 1 0037, 10714, 10668, 1103 7, 11363, 11585, 1166 7, 11709 Alba 10037, 10714, 10668, 11037, 1158 5 Alien 11037 Allstar 10037 Amstrad 10171, 10037, 110 37 Anam 10037 Anam National 10037, 1065 0 Andersson 11585 Anitech 10037 Ansonic 1003[...]

Remote Co ntrol Codes 12 Erres 10037 ESA 10171 ESC 10037 Euroman 1003 7 Europa 10037 Europhon 1003 7 Evesham 11248, 1 1667 Excello 11037 Exquisit 10037 Ferguson 10037, 10625, 105 60, 10195, 1103 7, 11585 Fidelity 10171, 1003 7, 10512 Finlandia 1020 8 Finlux 10556, 1 0037, 10714, 10715, 1124 8, 11667 Firstline 10556, 10037, 10714, 10668, 1103 7, 102[...]

Remote Co ntrol Codes 13 Lifetec 1003 7, 10714, 10668, 11037, 1200 1 Linsar 1158 5 Local India TV 10208 Local Malaysia TV 10698 Lodos 11037 Loewe 10037, 10512, 118 84 Logik 11037, 1069 8 Logix 1066 8 Luma 11037 Lumatron 10037, 10668 Lumenio 10037 Lux May 10037 Luxor 11037, 1020 8 LXI 10178 M Electronic 10037, 10714, 106 34, 10195, 1051 2, 11652 Mad[...]

Remote Co ntrol Codes 14 Phoenix 10037 Phonola 10556, 10037 Pioneer 10037, 10698, 10512, 11457, 1163 6, 12171 Plantron 10037 Playsonic 10037, 1071 4, 10715, 11652 Powerpoint 1003 7, 10698 Prinston 11037, 10715 Profitronic 10037 Proline 10037, 10625, 10634, 11037 Prosonic 10037, 10714, 10668, 11324, 1158 5, 11667, 11709, 1200 1 Protech 10037, 10668,[...]

Remote Co ntrol Codes 15 Technosonic 10556, 1062 5, 10499, 11324 Techvision 11709 Techwood 11037, 1 1667 Tecnimagen 10556 Teco 10178, 10653 Tedelex 10208, 1170 9 Teknika 10150 TELE System 11585 Telecor 1003 7 Telefunken 10037, 1 0625, 10714, 10560, 1069 8, 11585, 11667 Telefusion 10037 Telegazi 10037 Telemeister 10037 Telesonic 10037 Telestar 10556[...]

Remote Co ntrol Codes 16 Technics 10556 Thomson 10625 DVD 3D LAB 30539 Accurian 30675 Acoustic Solutions 30713 AEG 30675 AFK 31152 Aiwa 30533 Akai 30675 Alba 30539, 30713 Ambiance 33052 Amstrad 30713 Anthem 32820 Aristona 30539, 30646 ASDA 32213 Audix 30713 Autovox 30713 Awa 32587 Basic Li ne 30713 Bel Canto Design 31571 Black Diamond 30713 Blue Pa[...]

Remote Co ntrol Codes 17 Radionette 30741 Radiotone 3071 3 RCA 30522, 3057 1, 32213, 32587 REC 30490 Red 32213 Redstar 31394 Roadstar 30713 Rotel 30623 Salora 30741 Samsung 30490, 3 0573, 30199, 30820, 3163 5, 32069, 32329, 3248 9, 33195 Sanyo 30713 Schneider 30539, 30646, 30713 Schoentech 30713 Scott 31394 SEG 30713 Semp 30503 Sharp 30630, 3067 5,[...]

Remote Co ntrol Codes 18 Victor 31597 Yamaha 30646 Zenith 30741 HD-DVD Integra 3290 1, 33104 33 504 LG 30741 Microsoft 3208 3 Onkyo 3290 1, 33104 33 504 Xbox 32083 TV/DVD Combination Akai 11675 Black Diamond 11037, 3 0713 Blue Sky 11037, 3071 3 Bush 11037, 1069 8, 12719, 30713 Centrum 11037, 3071 3 Crown 1 1037, 30713 DMTech 12001 Dual 11037, 30713[...]

Remote Co ntrol Codes 19 Memo[...]

SN 29401094 (C) Copyright 2012 ONKY O SOUND & VISION CORPORA TION Japan. All rights reserved. * 2 9 4 0 1 0 9 4 * Y1112-1[...]