Oricom W1 инструкция обслуживания

W1 Series Water resistant DECT Cordless phone Keep this user guide for future reference[...]

2 Content Pack Cont ents ...................................................................................................... 3 IMPORTANT SAFETY INFORMA TION ............................................................... 4 GETTING STARTED............................................................................................ 5 Key Layout....[...]

3 OTHER FEAT URES ........................................................................................... 18 Key lo ck .............................................................................................................. 18 Shortcut to turn hands et ringer on/off ................................................................. 18 Mess[...]

4 IMPORTANT SAFETY INFORMATION • Avoid exposure of this telephone to moisture or liquid. • To prevent electric shock, do not open the handset or base cabinet. • Avoid metallic contact (e.g. metal clips, keys) between the battery contacts and charging conductors. • There is a slight chance that the telephone could be damaged by an electrical[...]

5 GETTING STARTED Key Lay out ¿ / Ringer On-Off LCD Display Talk / Recall Redial CID / Scroll backward Delete / Mute Program / OK Page # / Keylock / Pause Intercom / Conference Off / Exit Phonebook CID / Scroll forward[...]

6 LCD display on the handset The handset is linked to the base Displays the current battery level. It scrolls during charging. Appear together with either handset or base ringer setting. Use to set the handset ringer. Use to set the base ringer. Use to set the recall duration. Use to register the handset. There are more digits on the right There ar[...]

7 Basic steps to install This phone is not fully weather-sealed or waterproof. Its special construction provides protection against splashes and dripping water. Any water or liquid exposure other than the above may result in serious damage to the phone. THE BASE AND CHARGE POD ARE NOT WATER RESISTANT. ALWAYS WIPE DRY A DIRTY OR WET HANDSET BEFOR PU[...]

8 Wall mounting the base and charger 1. Turn the base over. 2. Attach the mounting bracket to the base as indicated. 3. The phone base units are suitable for wall mounting. Use two screws (not supplied) for fixing. Drill two holes horizontally side by side, 64mm apart for main base and 48mm for charger. Leave the screws protruding from the wall by [...]

9 charge. This is normal. A handset reaching a very low battery voltage level will go into sleep mode, displaying LOW BATT on the screen. It is good practice to replace t he handset on the base unit to charge when it is not in use to ensure t he handset is always fully charged. RISK OF EXPLOSION IF BATTE RY IS REPLACED BY AN INCORRECT TYPE. Refer t[...]

10 Making an external call Your phone allows you to dial out a phone number in various ways. Normal dialling 1. Press and wait for the dial tone. 2. Use the number pad to dial the phone number. The display shows the digits as you enter them. 3. When you enter more than 12 digits, turns on. In this case, you only see the last 12 digits on the screen[...]

11 The call timer will be displayed a short while after your call is connected. It shows the duration of the call. This timer is shown in minutes and seconds (MM-SS) in the first hour. After that, it will be shown in hours and minutes (HH-MM) with the “-“blinking to indicate the seconds. When you end a call, the timer will be displayed for 5 mo[...]

12 During a call, you will hear a loud tone the two loud beeps periodically to notify you of another incoming call. If you wish to answer this call 1. Press listen for dial tone then Press 2 to put the current call on hold and talk with the second caller. 2. Subsequent presses of listen for dial tone then Press 2 will toggle you between these 2 cal[...]

13 2. If there is caller name in the CID record, the first 8 characters are displayed for you to edit. If no caller name is available, you will be prompted to enter a name. 3. Press OK to save the name. You will not be able to save it if this name already exists in the phonebook. Edit the name and try again. 4. Edit the number if necessary and pres[...]

14 3. Press OK to save the name. You will not be able to save it if this name already exists in the phonebook. Edit the name and try again. 4. Edit the number if necessary and press OK to sa ve it. You have saved the number as a phonebook record. This record in the redial list will now show the name t hat you have assigned to this number. Deleting [...]

15 6. Press OK to confirm number change. Repeat steps 1 to 6 to edit another record. Deleting a phonebook record 1. During standby mode, press . 2. Press e or f to search for the record that you would like to delete. Or you can use the number keys to jump directly to the record starting with the corresponding letters of that key. 3. Press OK to sel[...]

16 6. Press OK to confirm your selection. will turn on if the handset ringer is turned off. Base Ringer Melody & volume 1. Press PROG during standby and press e or f until you see flashing. 2. Press OK to select. 3. Press e or f to listen to and select from the 5 melodies. 4. Press OK to confirm your selection and you will be prompted to volume[...]

17 3. Before you enter the PIN, press and hold on the base for 2 seconds until a registration tone is emitted. The base is now in the registration mode. (If the base is full and cannot take on any more handset, it will emit a reject t one instead. See the section of Deregister to delete a currently registered handset.) 4. Enter the PIN of the base [...]

18 OTHER FEATURES Key lock Press and hold during standby to lock the keypad. appears whenever keypad is locked. When the keypad is locked, you c an still answer an incoming call by pressing . During the call, the keypad functions as normal. When the call is ended, the keypad will be locked again. To unlock the keypad, press any key and then press O[...]

19 MULTI-HANDSET OPERATION You can use these useful features if you have 2 or more handsets registered to the base. Answ ering an internal call When you receive an intercom call, your handset will ring with blinking. You can see the calling handset number on the screen. If you press when the phone is ringing, the handset ringer will be turned off f[...]

20 During the conference call, pressing CONF will put the external line on hold and you can talk to the other handset in private. Press and hold CONF to establish the conference call again. Any handset hangs up during a conference call will leave the other handset still connecting with the external call. TROUBLESHOOTING Are you having trouble with [...]

21 NOTES FOR OPERATION IN NEW ZEALAND The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with the minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it pr ovide any sort of warranty. Above all, it provides no assu[...]

22 WARRANTY INFORMATION This product is covered by a 12 month warranty against defective workmanship or parts. The warr anty does not extend to damage caused by misuse, negligence, excessive vo ltage, faults on the telephone line or lightning. This guarantee in no way affect s your statutory rights. Full details of the warranty are contained in the[...]