Palsonic 3400 инструкция обслуживания

PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA:1300 657 888 34CM CORDLESS REMOTE COLOUR TELEVISION MODEL: 3400 OWNER'S MANUAL Type Tested Electrical Safety AS/NZS 3250 Lic 4163 Standards Australia APP No: N15957[...]

Congratulations on your purchase of this Palsonic colour television receiver. We recommend that you thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this receiver. Retain is manual in an easily accessible location for future reference. Contents Notes for operation ....................................[...]

. This equipment has been designed and manufactured to meet the highest international standards, but, like any electrical apparatus which is operated at mains voltage, care must be taken if you are to obtain the best results and safety is to be assured. This is particularly important with audio and TV equipment. read this handbook carefully and kee[...]

AV IN/OUT 1. ANTENNA CONNECTIONS 1.1 Optimum colour reception requires a good antenna. An out-door antenna will be more effective to obtain a clear-picture. 1.2 Insert the out-door antenna into the antenna socket on the cabinet back. Adjust the direction or position of the outdoor antenna for the best possible picture. 2. POWER SWITCH 2.1 Press the[...]

3.1 STANDBY ( ) Button 3.1.1 Press STANDBY ( ) button to turn on the set (the indicator shows yellow) when the set is in STANDBY mode (the indicator shows red) , the channel position number is displayed in the screen. Press STANDBY ( ) button to return the set to the STANDBY mode when the set is in OPERATION mode, and the indicator shows red. 3.2 C[...]

3.2.2.4 Press PRESET ON/OFF button to exit preset mode. The searched program station has been memorised at the present channel position, 3.2.2.5 Repeat 1~ 4 steps to search another channel. NOTE : * If the same channel position is selected during repeat operation, the former memory will be erased. * If some channel position is tuned by MANUAL TUNIN[...]

3.5 VOLUME CONTROL 3.5.1. Press the VOL button to increase volume ; the green bar on the screen moves right. 3.5.2. Press the VOL button to decrease volume ; the green bar on the screen moves left. 8 Display of minimum volume Display of maximum volume ......................... 3.6 AV/TV SELECTOR Press AV/TV button to change TV mode to AV mode when [...]

4. REMOTE CONTROL OPERATION: REMOTE CONTROL UNIT : STANDBY 1 ~ 9 : DIGITAL CHANNEL SELECTOR 10/0 : CHANNEL 10 OR CHANNEL 0 SELECTOR SYSTEM : COLOUR SYSTEM CONTROL -/- - : DIGIT OR TWO DIGIT CHANNEL SELECT : PREVIOUS 4.1 INSTALLING BATTERIES: 4.1.1 Remove the battery cover of Remote Control Unit. 4.1.2 Insert two "AAA", 1.5V batteries, mak[...]

4.3 CHANNEL SELECTION 4.3.1 Press CHANNEL SELECTOR ( ) the channel number will be increased or decreased and displayed in the upper right corner of the screen. 4.3.2 Use the DIGITAL CHANNEL SELECTOR button for direct channel selection. 1) 1~10 channel Method 1: Example: To select channel 2 To select channel 10 (Display) Method 2: Example: To select[...]

6 5 4.3.3 PREVIOUS BUTTON Pressing this button to select the channel that was tuned immediately before the one being watched. For example: If you are watching the program on channel 6, and the previous previous programme you watched was was on channel 15; then you can press the button to reach channel 15, press it again to return channel 6. 4.4 SOU[...]

4.6 Making use of PPS button (personal preference select) Press the PPS button, the screen will display the following five mode progressively: Press PPS again Press PPS again The above five display modes corresponding analogue quantity is shown in the following chart: BRIGHTNESS 4.7 DISPLAY BUTTON (DSP) Press this button, the present channel number[...]

4.8 SLEEP BUTTON 4. 8. 1 Using SLEEP button allows you to have the appliance automatically turned off after a pre-determined time, and set the appliance to STAND BY mode. 4. 8. 2 After the SLEEP function is set, the remaining time will be automatically displayed for 4 seconds every ten minutes. NOTE: * If you press STAND BY button while the SLEEP f[...]

4.9.1 CLOCK 4.9.1.1 Press the TIMER button till "CLOCK" displays-on the screen. 4.9.1.2 Press the button to set the present hour. Press the button to set the present minute. 4.9.1.3 After setting the clock, press TIME SET button to start operating. Now the indication on the screen is green instead of red. 4.9.1.4 Use DSP (DISPLAY) button [...]

AUTO 4.9.8.8 Press TIME SET button, then the OFF TIME indication is green instead of red. OFF TIME function starts operating. 4.9.8.4 The appliance will be turned off when your setting time is up, and return to stand by mode. NOTE: * The built-in clock employs the 24-hour system. * The OFF TIME function will be ineffective if the following conditio[...]

5. 2. 2 Press AV/TV button of the TV set or on the remote control unit to set the set to TV mode, and choose the desired channel. Note: the following mis-operation should be avoided during recording. * Press STANDBY button or set to VIDEO mode. * Change the current channel accidentally. 5.1.2 Press the AV/TV button on the TV set or on the remote co[...]

5. 3. 2 Press AV/TV button of the TV set or on the remote control unit to select Video mode before dubbing, "VIDEO" will be displayed on the screen. The TV set will act as a monitor to help you edit while dubbing. NOTE: The set MUST remain in Video mode and MUST NOT be switched off during the session. 14 5. 3 DUBBING 5.3.1 The picture bel[...]

6. TROUBLE SHOOTING GUIDE Symptoms Check these things Try these adjustment No picture, no sound. Be sure power cord is plugged in. May be station trouble. Check antenna connections. Maybe in AV mode. Press POWER BUTTON Try another channel. Press AV button once. Poor sound, picture OK. May be station trouble. May be local interference from another a[...]

7. SPECIFICATIONS: TV System: Receiver Channel Power supply CRT Antenna Impedance Dimension (mm) Weight Power Consumption Remote Control Unit Power Supply * Design and specifications are subject to change without notice. : PAL, B/G; NTSC 3.58/4.43 PLAYBACK : VHFL 0-5, 5A; VHFH 6-11; UHF 21-69 : AC 240V, 50Hz : 34 cm Diagonal : VHF/CATV/UHF 75 ohm :[...]

PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 604-37703-03[...]