Palsonic 5169M инструкция обслуживания

PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL: (02) 9313 7111 FAX: (02) 9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 51CM CORDLESS REMOTE COLOUR TELEVISION MODEL: 5169M OWNER'S MANUAL Type Tested Electrical Safety AS/NZS 3250 Lic 4164 Standards Australia APP No: N1595[...]

Congratulations on your purchase of this Palsonic colour television receiver. We recommend that you thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this receiver. Retain is manual in an easily accessible location for future reference. Contents Main features ..........................................[...]

. . . . . . . . . . . Main features Hyperband. Auto/manual search. Voltage synthesised system 100 preset channels. TV system: PAL-B/G, NTSC-4.43/3.58 (AV). Full function remote control & English on screen menu display No-signal blue background display and AUTO-POWER-OFF function. Four picture mode settings. Sound mute function. Sleep timer. AV [...]

Installation and appearance Antenna connection To ensure a bright-coloured and clear picture, you should use an outdoor aerial or CATV cable. If the signals are strong enough, you may use an indoor aerial. Note: When you connect the outdoor aerial cable to the aerial terminal on the TV set, please turn off the power switch on the TV while connectin[...]

Appearance Front view Standby Remote sensor Back view AUDIO OUT/IN Antenna input 5 Channel down/up (Channel select) Note: Functions of MENU, , VOL , CH and TV/AV are also provided to the remote controller. Menu TV/AV Volume down/up Power indicator Power switch VIDEO OUT/IN[...]

The remote controller Standby Channel direct select Sleep timer Picture mode selection *Sound system select Previous channel On screen recall Colour system select Picture control Volume control Channel select * NOTE: this TV model's RF sound system is BG only. Therefore the SYS1/2 button on the remote controller is ineffective in sound system [...]

Press again Operation Turning the power on/off 1. Connect the power, push the main power switch, the red indicator is on, the set is in standby mode. 2. Push the button on the remote controller to turn on the set when the set is in standby, this time, the green indicator is on, on the upper right corner of the screen will display channel number, co[...]

8 PROG 28 SYS 1 SKIP OFF AUTO AFT ON SEARCH BAND U MANUAL 1. PICTURE menu Making use of the PICTURE menu can adjust the picture effect according to your personal preference and it will be stored as picture memory mode automatically. Press the CH button to select the item (the selected item is highlighted in red). Press the VOL button to adjust it. [...]

Making use of the PRESET menu can fulfil the function of auto-search, search. manual search , channel and band selection. AFT and skip on/off. Press CH button to select the item. (the selected item is highlighted in red). Press the MENU button to exit to the main menu. 1) PROG (program) Select the current program number while "PROG" is hi[...]

10 STD AUTO BLUE ON Making use of the FUNCTION menu can select BLUE ON/OFF and current channel’s colour and sound system. Press CH button to select item (the selected item is highlighted). Press MENU button to exit to the main menu. 1) STD (colour system) selection. If the picture's colour system is abnormal, please select and highlight. &qu[...]

2) SYS (sound system) selection. In item is ineffective. (Refer to the NOTE on page 6) 3) BLUE ON/OFF selection. Select and highlight BLUE ON/OFF. Press VOL button to select ON or OFF. When "BLUE ON" is selected, blue background will appear on the screen automatically when no input signals, and the sound is mute. After 5 minutes the set w[...]

You can press the button to mute the sound. Press the button again or VOL button. The sound is restored to normal. 2. Volume adjustment You can press the VOL button to adjust the volume, and the green bar will move rightward or leftward, the volume output range is 0~63. SOUND MUTE MODE NORMAL SOUND MODE llllll...... Press Press Press VOL VOLUME 15 [...]

13 Press the button and the upper right corner will display the current channel number and TV system. After 4 seconds the display on the screen will disappear. Other functions 1. Retain on-screen display 2. TV colour system selection Press the STD button and each time the colour system displayed on the screen will change in the sequence of AUTO PAL[...]

COLOUR SYSTEM Colour Sub-Carrier Vertical Frequency PAL (RF/VIDEO) 4.43MHz 50Hz AUTO NTSC 3.58 (VIDEO) 3.58MHz 60Hz 50Hz PAL PAL 60 (VIDEO) N358 NTSC 3.58 (VIDEO) 14 4.43MHz 4.43MHz 3.58MHz 60Hz 60Hz PAL (RF/VIDEO) NTSC 4.43 (VIDEO) 4.43MHz 60Hz N443 3. SLEEP timer Using the SLEEP button allows you to have the appliance automatically turned off aft[...]

Note: 1) When receiving broadcasting TV program (the TV signals are input through aerial terminal), press the AV button to switch the set to TV mode. 2) When receiving programs played back by Video DISC., VCR, Satellite receiver, VCD (the signals are input through AV terminals), please set the receiver to AV mode. 15 12 PAL AV PAL Press AV Press AV[...]

Press AV button on the remote control unit to set TV mode, and choose the desired channel. At this time, the program recorded is displayed on the screen. Note: the following mis-operation should be avoided during recording. * Press STANDBY button or set to VIDEO mode. * Change the current channel accidentally. Press the AV button on the remote cont[...]

Press AV button on the remote control unit to select AV mode before dubbing, "AV" will be displayed on the screen. The TV set will act as a monitor to help you edit while dubbing. NOTE: The set MUST remain in Video mode and MUST NOT be switched off during the session. 17 3. DUBBING The picture below shows how to connect TWO VCRs to the TV[...]

TROUBLE SHOOTING Symptoms Check these things Try these adjustment No picture, no sound. Be sure power cord is plugged in. May be station trouble. Check antenna connections. Maybe in AV mode. Press POWER BUTTON Try another channel. Press AV button once. Poor sound, picture OK. May be station trouble. May be local interference from another appliance.[...]

Specifications Power Supply Receiver Channel Cable Channel Dimension (mm) Weight CRT Power Consumption Antenna Impedance Accessories Note : Design and specifications are subject to change without notice. : AC 240V, 50Hz : VHFL 0~5, 5A; VHFH 6~11; UHF E21-E69 : S1-S41 (Hyperband) : 590 (W) x 448 (H) x 486 (D) : 23 kg : 51cm : 70W : 75 ohm : one remo[...]

PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL: (02) 9313 7111 FAX: (02) 9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 604-56903-05[...]