Palsonic 9219SF инструкция обслуживания

PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA:1300 657 888 92CM CORDLESS REMOTE COLOUR TELEVISION MODEL: 9219SF OWNER'S MANUAL Type Tested Electrical Safety AS/NZS 3250 Lic 4166 Standards Australia APP No: N15901 HI[...]

Congratulations on your purchase of this Hi-VisionPalsonic colour television receiver We recommend that you thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this receiver. Retain is manual in an easily accessible location for future reference. * Screen displays and illustrations in this manual may di[...]

. . PAL/NTSC/SECAM Multi-System Hyperband English/Chinese on-screen menu display Surround sound and wide - field dynamic sound system NICAM Digital Stereo/bilingual broadcasts receivable German Stereo (IGR)/bilingual broadcasts receivable Three groups of S-VIDEO/VIDEO/AUDIO input terminals and one group of MONITOR output terminals Auto/manual searc[...]

NOTES FOR OPERATION * Do not let the TV set be in standby condition for a long period of time. When it is not in use, please turn off the power supply and remove the power plug. When it is to be left for a prolonged period of time, it is recommended to disconnect the connection to the outdoor aerial, to avoid thunder strike. * Please follow caution[...]

Installation and appearance Antenna connection To ensure a bright-coloured and clear picture, you should use an outdoor aerial or CATV cable. If the signals are strong enough, you may use an indoor aerial. Note: When you connect the outdoor aerial cable to the aerial terminal on the TV set, please turn off the power switch on the TV while connectin[...]

) terminals at the rear of the TV. Red wires should be connected to the + red terminals, while black wires to the - black terminals Speaker Connection As the figure below shows, attach the left and the right speaker to the sides of the set tightly, push the speaker from their top to secure them. Loosen the screws to remove the speaker from the TV 2[...]

Appearance Front view Back view 5 Note: Functions of , MENU, VIDEO, SYSTEM, VOLUME+/-, CHANNEL are also provided to the remote controller. SYSTEM CHANNEL CHANNEL MENU VIDEO VOLUME - VOLUME +[...]

The remote controller 6[...]

Operation Switching on/off Push the main power switch on, if the set is in Standby mode, the power indicator is red; If there are pictures appearing on the screen, the indicator is yellow. If no picture appears on the screen, push the power button on the remote controller to turn the set on, the indicator turns to yellow. Without using the remote c[...]

llllllllllllll Presetting the channels There are two ways to preset channels: to preset channels automatically and to preset channels manually. Below we will describe how to preset the channels by making use of the menu. 1. To enter into menu 1.1 Press the MENU button to enter into the main menu. 1.2 Press menu item select button or to select 1.3 P[...]

3. MANUAL SEARCH If AUTO-SEARCH cannot preset the desired channels, or you want to preset the desired channels one by one with the preferred channel numbers - please make use of MANUAL SEARCH. Press the menu item select button or to select MANUAL SEARCH (the caption on the screen are red). Press the or button to enter into the sub-menu of MANUAL SE[...]

When you want to store and memorise another channel with another position, repeat steps 3.3, 3,4. After presetting the channels, you can skip unwanted program numbers to select your desired channels. Repeat steps 3.1 to 3.3 to select the unwanted program position of the unwanted channels . Press the or button to select SKIP. Press the of button to [...]

6. The setting of colour and sound system Press the SYS button, the screen will display colour and sound system. If the displaying colour is abnormal, press the or button to select COLOUR, then press the or button to select the right colour system. Every time you press or button, the colour system will change in the sequence on the right. Press the[...]

FM mono sound two digital sound channels transmitting dual sound two digital sound channels transmitting dual sound one FM sound channel (The sound signal in FM channel is different from the one in NICAM channel. So when the NICAM is trans- mitting on the TV screen only displays an indicator in yellow, while the active sound channel is FM). Sound m[...]

Press the | button, you can quickly select two modes of picture and sound quality standard: One is standard mode ( on the screen displays (STANDARD); The other is personal select mode (on the screen displays "MEMORY"). 1. Picture adjustment Complete the following steps and you will adjust the picture quality. Press the MENU button, on the[...]

2. Sound adjustment Complete the following steps and you will adjust the sound quality. Press the MENU button to display the main menu. Press the or button to select SOUND , then press the or button to enter into the sub - menu of SOUND. Press the or button to select your required sound adjustment item (the caption on the screen is red), then press[...]

3. SURROUND SOUND Making use of surround sound, you can enjoy the dynamic sound effect that is like being in a music hall. To make use of surround sound, complete steps 2.1, 2.2 to select SURROUND ON, and press the button to select SURROUND then press the or button to adjust its effect. To turn off surround sound, select SURROUND OFF. 4. Adjusting [...]

Press the or button to select ON TIME. Pressing the or button set ONCE/EVERY ON TIME. Every time you press the or button , it will change in the sequence of OFF EVERY ONCE OFF EVERY ------. When the setting is ONCE or EVERY ON TIME, press the or button to select time to turn on the set, then press the or button to set the time to turn on the TV. Af[...]

Pressing the button set the TV into standby mode. At the preset time the TV will automatically turn on to preset channel. To cancel ON TIME, set ON TIME OFF. 1.3 CLOCK The built-in clock employs the 24-hour system. Do step 1.1.1 to enter into the sub-menu of TIMER. Press the or button to select CLOCK. Pressing the or button set the present hour and[...]

External Equipment Connections The following describes how to use and connect the TV with other equipment. Refer to the owner's manual of the other equipment to be connected as well. 1. To Connect to AV input You can video equipments such as a VTR and video camera to this TV and enjoy the high quality picture and sound. If your video equipment[...]

To select the input press the VIDEO button on the TV set or the AV button on the remote controller repeatedly until you see the corresponding input indication on the screen. To return to aerial input, press the AV button until it displays programme number, or press direct channel select button or the CH button. VIDEO 1 VIDEO 2 VIDEO 3 If the colour[...]

Troubleshooting Symptoms No power, red indicator is not lit up Poor colour, poor tint Spots appear on the screen Stripes appear on the screen Double images or "ghosts" Snowy picture The remote controller does not work The drawer of the control buttons opens slowly The drawer of the control buttons can not open TV cabinet creaks Check the [...]

Specifications: Power supply: Power consumption: Dimension (mm): Weight: (kg) CRT: TV system & channel range System PAL-D/K PAL-B/G PAL-I NTSC-M U/S SECAM-B/G SECAM-D/K Colour system: Sound system: Sound output: Accessories: * NOTE: Design and specifications are subject to change without notice. AC 240V, 50Hz 220W 860 (W) x 740 (H) x 600 (D) 11[...]

604-38783-01 PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888[...]