Panasonic KX-A272 инструкция обслуживания

Model KX-A272 Operating Instructions DECT Repeater Please read before use and save. QUQX00130YA_01_A 20/1/04 6:40 pm Page 1[...]

2| Operating Instructions T able of Contents Overview ..........................................................................................................3 Compatibility......................................................................................................3 General Safety ........................................................[...]

Operating Instructions | 3 Overview A repeater is used when you need to extend the range of your cordless DECT telephone or PBX cell station, to include areas where reception was previously not available. The repeater extends the range in all directions, allowing several floors to be covered. Up to 6 repeaters can be registered at a DECT base unit,[...]

4| Operating Instructions Environment • Do not use this unit near water . • This unit should be kept away from heat sources such as radiators, cookers, etc. It should also not be placed in rooms where the temperature is less than 5 º C or greater than 40 º C. • The AC adaptor is used as the main disconnect device. Ensure that the AC outlet [...]

Operating Instructions | 5 W all Mounting This unit can be mounted on a suitable wall or placed on a flat surface. • Insert screws into wall. A void pipes and electrical cables etc. that may be present/buried. The centre of the screws must be 71mm apart. Allow a protrusion of 2mm from the base of the screw head to the wall, using the washer provi[...]

6| Operating Instructions Placement To get the best performance from the repeater: • Select a raised position (on wall etc), which is well within range of the Base Unit/Cell Station. •A void positioning the repeater close to objects that will interfere with reception, such as thick walls, radiators, metal shelving etc. • For maximum distance [...]

Operating Instructions | 7 Automatic Registration Automatic registration cannot be performed if the repeater is already registered to another base unit or cell station. Please follow the DE-REGISTRA TION procedure on page 10 before attempting Automatic Registration. • Ensure that the repeater is switched off (disconnect the AC adaptor) (both LEDs[...]

8| Operating Instructions Manual Registration There must be at least one handset already registered to the base unit or cell station to carry out manual registration. • Ensure that the repeater is switched off (disconnect the AC adaptor) (both LEDs are OFF). • Power on the repeater , by connecting the AC adaptor . The red LED will light for 2 s[...]

Operating Instructions | 9 Manual Registration continued. • Press ‘off hook’ on the handset. The green LED will go steady ON. • Enter a unique identifying number on the handset keypad for each repeater registered. The identifying number can be 2 to 7 for domestic DECT products, and 000 to 255 for PBX DECT products. The digit will display on[...]

10 | Operating Instructions De-Registration In order to perform de-registration, the repeater must have already been registered to a base unit or cell station. • Ensure that the repeater is switched off (disconnect the AC adaptor) (both LEDs are OFF). • While holding down the repeater switch, power on the repeater by connecting the AC adaptor .[...]

Operating Instructions | 11 V erification T one Repeater coverage can be checked by using the in-built verification tone. The coverage area of the repeater can be checked - if the ‘beep’ is no longer heard, then the handset is no longer in range of the repeater . • Ensure the repeater is powered ON, and the green LED is steady ON. •T o acti[...]

12 | Operating Instructions Site Survey Mode (PBX option only) This function can be used to measure the transmission quality , and identify problematic transmission areas of the repeater installation. This function can be used when registered or de-registered. • Ensure the repeater is powered OFF before starting. •T o activate the site survey m[...]

Operating Instructions | 13 Serial Repeater ID programming (PBX option only) This function is used to control up to 3 repeaters in a chain configuration on a PBX system. T o ensure correct operation (and to avoid circular linking), each repeater must be assigned a different chain-level (1 – 3). The first repeater (nearest the cell station) is ass[...]

14 | Operating Instructions Serial Repeater ID programming continued. • Ensure that the repeater is switched OFF . (both LED’s are OFF) • Power ON the repeater . • Assign the repeater to a base by following either the manual or automatic registration process. • Bring the repeater into close range of the repeater on the parent level (i.e. [...]

Operating Instructions | 15 Before Requesting Help Problem Possible Cause Solution No function No power Check AC cord is plugged in (LED not lit) Not turned on Check AC adaptor is switched on Cannot register Out of range of base Move repeater closer to base unit (Green LED flashes) or cell station, or base or cell station unit cell station not Repe[...]

16 | Operating Instructions T echnical Information Specifications Standard: DECT=(Digital Enhanced Cordless T elecommunications) Number of channels: 2 Duplex Channels Frequency Range: 1.88GHz to 1.9GHz Duplex Procedure: TDMA (Time Division Multiple Access) Channel spacing: 1728 kHz Bit rate: 1 152 kbit/s Modulation: GFSK RF T ransmission Power: App[...]

Operating Instructions | 17 CONDITIONS OF GU ARANTEE This guarantee is in addition to and does not in any way affect any statutory or other rights of consumer purchasers. If within the applicable guarantee period, the appliance proves to be defective by reason of faulty design, workmanship or materials, we undertake subject to the following conditi[...]

18 | Operating Instructions Index A ccessories ......................................................................................................4 Automatic Registration ......................................................................................7 B efore Requesting Help.................................................................[...]

Operating Instructions | 19 QUQX00130YA_01_A 20/1/04 6:41 pm Page 19[...]

Hereby , Panasonic Communications Company (U.K.) Limited declares that this (KX- A272E) is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A copy of the manufacturer ’s declaration of conformity to the essential requirements of the R&TTE Directive is available at the following web address: h[...]