Panasonic WV-CM1480 инструкция обслуживания

Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. Model No. WV -CM2080 WV -CM1780 WV -CM1480 Color Monitor Operating Instructions POWER Video Monitor WV-CM 2080 O N O F F AUDIO MENU STANDBY INPUT SELECT ENGLISH FRANÇAIS[...]

2 The serial number of this product may be found on the rear of the unit. You should note the serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft. Model No. Serial No. WARNING: To reduce the risk of fire or electric shock, do not expose this applian[...]

3 The Panasonic WV-CM2080, WV-CM1780 and WV-CM1480 Color Monitor’s high resolution S-video input assures high definition picture quality. All monitor functions, except for power and input selection, can be controlled from an onscreen menu. Provided with power saving feature as well as standard BNC and S-video input connectors for connection to CC[...]

4 MAJOR OPERA TING CONTROLS AND THEIR FUNCTIONS ON OFF POWER STANDBY INPUT SELECT MENU – + AUDIO Video Monitor WV-CM 2080 q w e t y u r * The above figures represent model WV-CM2080. q Power Button (POWER ON/OFF) This button turns the power of the monitor on and off. w Power Indicator Is on when the power of the monitor is turned on, also in stan[...]

5 !5 Standby Control Terminal (STANDBY ON/STANDBY OFF/G) This terminal accepts input from an outboard device to control the standby mode. It operates as follows: STANDBY ON: Establishes the specified standby mode. STANDBY OFF: Releases standby mode (normal dis- play). !6 Audio Input Connectors (AUDIO IN A/B) For audio input from an outboard device [...]

6 INST ALLA TION The installation described below should be made by qualified service personnel or system installers. ■ Mounting into the Rack for WV -CM2080 The monitor can be mounted into the rack as described below. P O W E R Video Monitor W V -C M 2080 2080 ON OFF A U D IO M E N U S T A N D B Y IN P U T S E L E C T 2. Install the monitor with[...]

7 ■ Connection with the Camera Site Connect the Video Output of the camera site equipment to the VIDEO IN connectors on the rear of the monitor using coaxial cables. The maximum coaxial cable lengths between the cameras are shown below. ■ Connection with the VCR • Recording on the VCR Connect the VIDEO OUT A or B connector on the moni- tor to[...]

8 ■ Connection between two or more color monitors and a device compat- ible with Panasonic Security Data mode In case of connecting multiple devices compatible with the Panasonic Security Data mode, connect the unit in a daisy-chain configuration as shown below. The allowable connecting devices are up to 16 in a system. The maximum allowable cabl[...]

9 SETUP PROCEDURES This monitor offers various onscreen menus for setting user preferences. In the COMMUNICATION SETUP Menu, you can set the parameters for communication between the System Controllers and the Monitors. ■ Displaying the Setup Menu To display the Setup Menu, follow the procedure shown below. 1. Confirm that the cameras and peripher[...]

10 ● Baud Rate (BAUD RA TE) This item lets you set the transmission speed for RS-485 communication. 1. Move the cursor to the BAUD RATE parameter with the C or D button. 2. Select the desired transmission speed shown below with the - or + button. The factory default setting is 9 600 bps. ● Data Bit (DA T A BIT) This item lets you set the number[...]

11 ■ Power Up Before operating the monitor, confirm that the cameras and peripherals are connected correctly and securely. 1. Turn on the monitor by pressing the POWER button. The Power Indicator lights in green. 2. Select the desired input to be displayed by pressing the INPUT SELECT button. Pressing this button will select the display (or audio[...]

12 9. Move the cursor to the AUDIO parameter with the C or D button, then adjust the audio volume with the - or + button. - : Decreases the audio volume. + : Increases the audio volume. 10. Move the cursor to the STANDBY ON parameter with the C or D button, then select the desired mode with the - or + button. These modes refer to the display mode i[...]

13 ■ Audio V olume Control The audio volume can be adjusted with the - or + button in normal view. While the volume is being adjusted, the indicator displays the changed level as shown below. - : Decreases the audio volume. + : Increases audio volume. ■ Standby Function 1. Power up the monitor and select the input to be displayed. Refer to Powe[...]

14 OPERA TING PROCEDURES (with the System Controller) For the following procedure, the WV-CM2080, WV-CM1780 or WV-CM1480 needs to be set up first from the Setup menu. The WV-CM2080, WV-CM1780 or WV-CM1480 can be controlled with the specified System Controller. Given below is an example. For further details refer to the Operating Instructions suppli[...]

15 APPENDIX This appendix details the elements for communication between the Monitor and the System Controller. For the communication parameter settings, refer to the SETUP PROCEDURES on page 9. ■ Communication Protocol ● Data Format The controller sends messages to operate the monitor in the format shown below. A transmission message consists [...]

16 ■ Function Number T able The list below shows the function numbers assigned to the monitor when controlling it with the specified System Controller. Function Number Function 001 NORMAL SETTINGS: Reset the items on the page in the Display Setting menu to the factory default settings. 002 Brightness Control: Reset to value 0 003 Brightness Contr[...]

17 Power Source: 120 V AC, 60 Hz Power Consumption: WV-CM2080: 90 W WV-CM1780: 73 W WV-CM1480: 70 W Screen Size: WV-CM2080: 548 mm (21-9/16”) diagonal tube size 508 mm (20”) viewable size WV-CM1780: 444 mm (17-1/2”) diagonal tube size 406 mm (16”) viewable size WV-CM1480: 394 mm (15-1/2”) diagonal tube size 356 mm (14”) viewable size Ho[...]

18 Power Cord ................................................................. 1 pc. Rack Mounting Bracket ............................................... 2 pcs. (WV-CM2080) Fixing Screws for Rack Mounting Bracket ................. 8 pcs. (WV-CM2080) ACCESSORIES[...]

Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010 Panasonic Sales Company Division of Matsushita Electric of Puerto Rico Inc. Ave. 65 de Infanteria. Km. 9.5 San Gabriel Industrial Park, Carolina, Puerto Rico 00985 (809)750-4300 Panasonic Security and Digital Imaging Company A Division of Matsushita Electric[...]