Paslode Paslode 403606-10 инструкция обслуживания

P Operating and Maintenance Manual PNEUMA TIC T OOLS 403606-10 08/02[...]

P ASLODE MODEL NUMBER DESIGNA TION The model number of each Paslode tool contains information about the tool and the fasteners that are used with it. The following example illustrates the information contained in this tool model number. ST APLER Tool application letter Maximum fastener length, in inches that can be used with the tool 00 - S 00 P Ty[...]

INTR ODUCTION Congratulations on purchasing a Paslode pnuematic tool. Y ou have made a wise choice. A Paslode tool is a professional quality tool that combines power and speed in a light weight design for versatile operation in a variety of industial and construction applications. Please take the time to review this entire manual and all other docu[...]

W ARNING Failure to follow any of the above instructions could result in severe personal injury to tool user and bystanders or cause damage to tool and property . Contact your local Paslode Representative for presentation of Paslode’s Safety Awareness Program SAFETY INSTR UCTIONS SAFETY FIRST These safety instructions provide information necessar[...]

5 AIR SYSTEMS For air-powered tools to work their best, the air supply system must be properly installed and maintained regularly . A drawing in this section shows a properly installed air supply system. Handy checklists for installing and maintaining air supply systems follow . Indoor Air System Installation -Be certain that: • All pipes supplyi[...]

AIR SYSTEMS - Continued Calculating Compressor Size Use the air consumption chart in the T ool Schematic for each tool when calculating the operating requirements for the tools. Paslode tools are designed to operate efficiently between 80 and 120 psi and should never be operated at pressure greater than 120 psi. The air consumption chart will help [...]

T OOL INST ALLA TION Y our Paslode tool comes ready for immediate use and can be installed by following these steps: 1. SAFETY - All tool operators and their immediate supervisors must become familiar with the operator safety instructions before operating the tool. The instructions are on page 2 of this manual. 2. Included wuth each tool are one co[...]

Precision Placement Driving ■ Grasp the tool handle firmly and hold the bottom of the work contacting element firmly against the workpiece until it is com- pletely depressed. ■ Squeeze the trigger to drive the fastener. ■ Lift the tool from the workpiece. ■ Repeat the procedure for the next fastener. Successive (Bounce) Driving ■ Grasp th[...]

Coil Nailers Step No. 1 – Grasp the nailer handle firmly with one hand and with the other hand unlatch the magazine cover clip. Swing the magazine door open. Step No. 2 – Adjust the loading tray for nail length (if required) by depressing the button on the post and raising or lowering the tray to the desired position. Step No. 3 – Remove the [...]

T250-F16 Series Finish Nailer Step No. 1 – Grasp the nailer firmly with one hand. Step No. 2 – Insert the strip with the point of the fastener facing down towards the bottom of the magazine. Step No. 3 – Hold the follower firmly and press the follower latch. Slide the follower forward until it contacts the nails. The tool is now ready for use[...]

2000 Series Stapler Step No. 1 – Grasp the stapler firmly with one hand. Depending on the model,either squeeze the latch with your small finger or press it with your thumb With your other hand, pull the magazine back towards you. Step No. 2 – Insert the fastener strip into the magazine rail. Step No. 3 – Push the magazine firmly towards the f[...]

MAINTENANCE Paslode ® tools are built for ease of maintenance. A few simple details will assure trouble-free operation and long tool life. Anyone who uses or maintains the tool must read the safety and maintenance instructions. Study the sche- matic drawing before starting any repairs on the tool. Air-operated tools must be inspected periodically,[...]

MAINTENANCE - Continued Drain air line filter(daily). Keep lubricator filled. Clean filter element-then blow air through filter in direction opposite to normal flow. Check that all screws on tool are tight. Keep work contacting elelment working properly. Keep magazine and feeder mechanism clean. Lubricate "O" rings that are replaced. Use [...]

OPERA T OR TROUBLESHOO TING PR OBLEM CORRECTIVE A CTION Fasteners will not drive completely into wood. Fasteners penetrate properly during normal operation, but won't drive fully at faster speeds. Fasteners drive too deeply into wood. Fastener jams in nose of tool. Tools skips during operation - no fasteners are driven from time to time. Tool [...]

TOOL W ARRANTY T OOL W ARRANTY AND LIMIT A TIONS An Illinois T ool Works Company 888 Forest Edge Drive V ernon Hills, Illinois 60061 P 15[...]