Patton electronic 1080A инструкция обслуживания

USER MANUAL MODEL 1080A and MODEL 1080A-64 Universal Synchronous & Asynchronous Short Range Modems SALES OFFICE (301) 975-1000 TECHNICAL SUPPO R T (301) 975-1007 http://ww w .patton.com Part #07M1080A-D Doc. #072041UD Revised 6/19/98 CERTIFIED An ISO-9001 Certified Company[...]

1.0 W ARRANTY INFORMA TION Patton Electronics warrants all Model 1080A Series components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of shipment. This warranty is limited to defects in workmanship or materials, and does not cover customer damage, abuse or unaut[...]

2.0 GENERAL INFORMA TION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected by Patton's qualified technicians. If any questions or problems arise during installation or use of this product, please do not hesitate to contact Patton Electronics T echnical Support at (301) 975-1007. 2.1 FEA [...]

Each Model 1080A Series SRM has three sets of eight switches, yielding 24 total DIP switches. The three sets will be referred to as S1, S2 and S3. As Figure 2 shows, the orientation of all DIP switches is the same with respect to “ON” and “OFF” positions. 3.2 CONFIGURA TION SWITCH SET “S1” The DIP switches on S1 set data rate, clock sou[...]

Switch S1-8: Carrier Control Method The setting for switch S1-8 determines whether the carrier is “constantly on” or “controlled by RTS”. This setting allows for operation in switched carrier , multipoint and/or hardware handshaking applications. S1-8 Setting Off Constantly on On Controlled by RTS 3.3 CONFIGURA TION SWITCH SET “S2” The [...]

3.4 CONFIGURA TION SWITCH SET “S3” The DIP switches on S3 set the anti-stream control, local loopback enable, remote loopback enable and receive (input) impedance levels for the Model 1080A Series. Factory default positions of Switch S3 are shown in the table below . Switches S3-1 & S3-2: Input Impedance The setting for Switches S3-1 and S3[...]

Switch S3-6: RS-232 Initiation of Remote Loopback T est The setting for switch S3-6 determines whether or not the Model 1080A Series’ remote digital loopback test can be initiated by raising pin 21 on the RS-232 interface. S3-6 Setting On RS-232 initiation enabled Off RS-232 initiation disabled Switches S3-7 and S3-8: Anti-stream Control Switches[...]

4.1.1 T wo-Wire Cable Connection Via RJ-45 A. The RJ-45 jack on a Model 1080A Series Short Range Modem is prewired for a standard TELCO wiring environment. T o be sure you have the right wiring, use the table below as a guide. RJ-45 SIGNAL 1 -------------NC 2 -------------GND † 3 -------------RCV 4 -------------XMT 5 -------------XMT 6 ----------[...]

4.2.1 Four-Wire Cable Connection Via RJ-45 A. The RJ-45 jack on a Model 1080A/1080A-64 Short Range Modem is prewired for a standard TELCO wiring environment. T o be sure you have the right wiring, use the table below as a guide. RJ-45 SIGNAL 1 -------------NC 2 -------------GND † 3 -------------RCV 4 -------------XMT 5 -------------XMT 6 --------[...]

4.3 FOUR-WIRE, MUL TIPOINT INST ALLA TION Multipoint operation involves the connection of several terminals to one host port. In such an application, one local Model 1080A/1080A-64 is used as a master unit, and it is connected to several remote Model 1080A/1080A-64s that are acting as slaves. Up to 25 Model 1080A Series slaves may be connected to o[...]

5.1.4 The “Error” Indicators The “Error” indicator LED has three functions: A. When the 1080A Series unit is in test mode (green “T est” LED is lit), the error LED glows red when bit errors occur . B. When not in test mode (green “T est” LED is off), the error LED is used to indicate an RTS streaming condition. (See Section 5.2) for[...]

5.1.4.2 Reading The T est A. If line quality is good, “Error” LED on local modem will not light and “CD” LED will be red. On remote modem “Error” LED will not light and “CD” LED will light green. B. If flat cable is used or parts of the line are flat cable, “Error” LED on local modem will light red and “CD” LED will light gr[...]

A. Activate RDL. This may be done in two ways: First, by moving the front panel toggle switch UP to "Remote". Second, by raising pin 21 on the RS-232 interface (Note: Make sure DIP switch S3-6 is ON; and DIP switch S2-6 is OFF). B. Perform a BER (bit error rate) test on the system. C. If the BER test equipment indicates a fault, and the L[...]

APPENDIX B P A TT ON MODEL 1080A SERIES F ACT OR Y REPLACEMENT P ARTS AND ACCESSORIES Patton Model # Description 080510ACB .....................120V W all Mount AC Adapter 08059ACI ........................230V AC Adapter (No Power Cord) 07M1080A .......................Model 1080A Series User Manual 25 APPENDIX C P A TT ON MODEL 1080A SERIES CABLE R[...]

APPENDIX C P A TT ON MODEL 1080A SERIES INTERF ACE PIN ASSIGNMENT RS-232 FEMALE, D-SUB 25 CONNECTOR (DCE ORIENT A TION) 1- (FG) Frame Ground 2- (TD) T ransmit Data T o 1080A 3- (RD) Receive Data From 1080A 4- (RTS) Request to Send T o 1080A 5- (CTS) Clear to Send From 1080A 6- (DSR) Data Set Ready From 1080A 7- (SG) Signal Ground 8- (DCD) Data Carr[...]