Pelco C2410M-I (1/06) инструкция обслуживания

INST ALLA TION 150 Series Camclosure ® Integrated Camera Sy stem C2410M-I (1/06) In-Ceiling Mount[...]

[...]

C2410M-I (1/06) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Inst all in accordance with the manufacturer’ s instructions. 6. Do not install near any heat sources such as radiators, heat registers, st oves, or oth[...]

4 C2410M-I (1/06) Regulatory Notices This device complies with Part 15 of the FCC Rule s. Operation is subject to the following two conditions: (1) this device may not cause harmful in terference, and (2) this device must accept any interference received, incl uding interference that may cause undesired operation. FCC, Class A (black-white, EIA and[...]

C2410M-I (1/06) 5 Description The 150 Series Camclosure ® integrated camera system is an in-c eiling dome incorporating a camera and lens package into a small, discreet, high-security enclosure designed for areas subject to heavy vandalism. The system is perfect for a variety of indoor and outdoor applicat ions and its versatile design allows for [...]

6 C2410M-I (1/06) Installation INSTALL BACK BOX MOUNTING DIRECTLY TO A W ALL OR CEILING 1. Cut a hole 3.5 inches (9 cm) in diameter in the ceiling or wall using the adapter plate as a template. 2. Connect the video cable. 3. Connect the power wires. • For 12 VDC, connect the 24 V AC/12 VDC (red) and GND (black) wires to input power . The blue wir[...]

C2410M-I (1/06) 7 MOUNTING TO CEILING T ILE 1. Remove the ceiling tile. 2. Using the adapter plate as a template, cut a hole 3.5 inches (9 cm) in diameter in the ceiling tile for the back box. Punch four screw holes in the ceiling tile. 3. Attach the back box to the ceiling tile and adapter plate with the four 8-32 x 1.25-inch screws (see diagram).[...]

8 C2410M-I (1/06) 3. If the heater is installed, plug the heater connector from the camera into the mating connector inside the base. Plug the video connector from the camera into the mating connector inside the base. T urn on power to the camera and monitor . 4. If you have a varifocal lens, hold the assembly in your hand and point the lens toward[...]

C2410M-I (1/06) 9 INSTALL DOME AND T RIM RING Place the trim ring and dome over the back box. If the dome has a liner , position the viewing window over the lens of the camera. T i ghten the tamper -resistant screws with the supplied 1/ 8-inch hollow screwdriver bit. Note that the screw s are installed at an angle. Adjustments (Color Camera Only) I[...]

10 C2410M-I (1/06) AUTO IRIS LEVEL ADJUSTMENT If you have a varifocal lens or fixed focal length l ens with an auto iris, you c an adjust the level setting to increase or decrease brightness. FOCUS ADJUSTMENT FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS . T o adjust the focus, it may be necessary to remo ve the heater board in orde r to loosen the lo[...]

C2410M-I (1/06) 11 SWITCH SETTINGS FOR FIXED FO CAL LENGTH LENS WITH AUTO IRIS Refer to the switch drawing. The switch is located ne xt to the lens. Automatic backlight compensation (factory setting) is used under varying lighting conditions (such as outdoors) or fixed lighting conditions where t here are no bright spots t hat darken other picture [...]

12 C2410M-I (1/06) SWITCH SETTINGS FOR V ARIFOCAL LENS The high resolution camera with varifocal lens and aut o iris is configured at the factory for automatic exposure. For manually setting and locking the white balance, plac e a white background in front of camera and turn off switch 1. For gamma correction, switch to accurately repr oduce scene [...]

C2410M-I (1/06) 13 Specifications GENERAL Operating T emperature -50° to 122°F (-46° to 50°C) De-ices to 25°F (-4°C) Pan/T ilt Adjustment Manual; 360° pan; 180° tilt Construction Aluminum with steel came ra mounting bracket and polycarbonate dome Finish White polyester powde r coat trim ring with charcoal gray back box Dimensions Refer to d[...]

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, witho ut charge, any mer c handise proved defective in ma terial or wo rkmanship for a period of one year after th e date of shipment. Exception s to this warrant y are as noted be low: • Five years on F T/FR8000 Series fiber o ptic products. • Three years on Genex ?[...]

REVISION H ISTORY Manual # Date Comments C2410M 11/99 Original version. C2410M 1/00 Revised installat ion instructions. Ad ded FCC notices. C2410M-A 1/00 Added varifoc al lens. Changed form at. C2410M-B 7/00 Added information on dome liner. C2410M-C 1/01 Added heater element cauti on. C2410M-D 7/01 Camera module red esigned, referenc e ECO 1-7054/7[...]

Worl dwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East[...]