Pelco CCC1380H-6X инструкция обслуживания

CCC1380H-6, CCC1380H-6X, and MCC1380H-6 C1963M (8/04) ® INST ALLA TION/OPERA TION 1/3-Inch CCD Camera[...]

2 C1963M (8/04) CONTENTS Section Page IMPORT ANT SAFETY INSTRUCTIONS ............................................................................................... 3 REGULA TORY NOTICES ............................................................................................................. 4 DESCRIPTION .......................................[...]

C1963M (8/04) 3 This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. IMPORT ANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed[...]

4 C1963M (8/04) REGULA TORY NOTICES This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This[...]

C1963M (8/04) 5 DESCRIPTION The CCC1380H-6, CCC1380H-6X, and MCC1380H-6 digital cameras are high resolution, compact video cameras that feature a 1/3-inch CCD imager . Each camera’ s high resolution and high-density image sensor ensure a sharp and clear picture over a wide range of conditions. MODELS CCC1380H-6 1/3-inch, high resolution, color CC[...]

6 C1963M (8/04) LOCA TION AND FUNCTION OF P ARTS  Lens Mount The camera has a standard CS lens mount but can use a C-mount lens when a C/CS-mount adapter is installed between the lens and camera.  Back Focus Lock Screw Loosen the locking screw to adjust the back focus. Back focus adjustment has been set at the factory to the standard CS-mount[...]

C1963M (8/04) 7  Eclipser Level Controls The eclipser function is set at the factory and usually does not need to be readjusted. However , if adjustment is necessary , refer to the section on Eclipser Adjustment in this manual. THRE Sets the level for the brightest part of the picture. Anything brighter than this adjustment will be eclipsed. ECL[...]

8 C1963M (8/04) A WB – Automatic White Balance Following are the AWB switch settings: OFF – Processes the viewed image to retain color balance in a restricted color temperature range. ON (Default setting) – Automatically processes the viewed image to retain color balance over a wide color temperature range. SYNC – Synchronization Locks the [...]

C1963M (8/04) 9 CONNECTIONS POWER To connect to the power supply: 1. Strip at least .50 inch (13 mm) from the power cord to expose the wires. 2. Insert the three wires into the holes in the terminal strip until they snap into place. 3. Confirm that the cord is connected to terminal securely by lightly tugging on the cord. If you are wiring more tha[...]

10 C1963M (8/04) LENS INST ALLA TION The CCC1380H-6, CCC1380H-6X, and MCC1380H-6 can use fixed, manual, or passive (DC- controlled) auto iris lenses. The camera has a standard CS lens mount but can use a C-mount lens when a C/CS-mount adapter is installed between lens and camera. LENS MOUNTING 1. Screw the lens onto the lens mount. Be careful to pr[...]

C1963M (8/04) 11 BACK FOCUS ADJUSTMENT Do not release the back focus locking ring unnecessarily . Back focus adjustment has been set at the factory to the standard CS-mount back focus distance. However , once a lens is mounted it may be necessary to adjust back focal length to match the lens being used. FIXED FOCAL LENGTH LENSES 1. Mount the lens f[...]

12 C1963M (8/04) CAMERA SYNCHRONIZA TION The power supply of each camera is set to the same synchronized phase at the factory and usually does not need to be readjusted. When using more than one camera power supply , a brief vertical roll may occur on the monitor each time a camera view is switched. T o eliminate vertical roll, adjust the phase con[...]

C1963M (8/04) 13 ECLIPSER ADJUSTMENT The eclipser function is set at the factory and usually does not need to be readjusted. However , if fine tuning is necessary , do the following: 1. Set the DIP switches. a. AGC: OFF b. ESC: OFF c. BLC: OFF 2. Set the variable resistors and Eclipse DIP switch. a. THRE: Counterclockwise b. ECLP: Mechanical center[...]

14 C1963M (8/04) SPECIFICA TIONS GENERAL Imaging Device 1/3-inch interline transfer CCD Picture Elements CCC1380H-6, MCC1380H-6 768H x 494V (approx. 380K) CCC1380H-6X 752H x 582V (approx. 440K) Sensing Area 3/16 x 1/8 - inch (4.7 mm x 3.5 mm) Synchronization System AC line lock/DC internal Horizontal Resolution CCC1380H-6, CCC1380H-6X 480 TV lines [...]

C1963M (8/04) 15 PRODUCT W ARRANTY AND RETURN INFORMA TION W ARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on the following fixed camera models: CC3701H-2, CC3701H-2X[...]

Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO 9001 ® United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East[...]