Poulan Pro 199340 инструкция обслуживания

OWNER'S MANUAL MODEL NUMBER: PP5524ES SNOW THROWER Alwa ys W ear Ey e Pr otection During Operation IMPORT ANT MANUAL Do Not Throw A way W ARNING: Read the Owner's Manual and fol low all W arnings and Safety In struc tions. Fail ure to do so can result in serious injury . 199340 Rev . 1 01.1 1.06 BY Printed in U.S.A.[...]

2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury . W ARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be e[...]

3 CONGRA TULA TIONS on your purchase of a new snow thrower . It has been designed, engineered and man u fac tured to give best possible dependability and per for mance. Should you experience any problem you cannot easily remedy , please contact your nearest authorized service center . We have competent, well-trained tech ni cians and the proper too[...]

4 Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower . Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly , operation and maintenance of the product. Y our new snow thrower has been as sem bled at the factory with the ex cep tion of t[...]

5 ASSEMBL Y / PRE-OPERA TION NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making ad just ments to the skid plates. UNFOLD UPPER HANDLE 1. Raise upper handle to the operating position and tight en handle knobs securely . INST ALL SPEED CONTROL ROD (See Figs. 1 and 2) 1. Remove plastic tie securing rod[...]

6 ASSEMBL Y / PRE-OPERA TION INST ALL DISCHARGE CHUTE / CHUTE ROT A TER HEAD (See Fig. 7) NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotater head. 1. Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower . 2. Position chute rotater head over chute bracket. If [...]

7 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literat[...]

8 OPERA TION Throttle/engine control - used to se lect either F AST or SLOW engine speed and to STOP the engine. T raction drive control lever - used to engage power-pro- pelled for ward or reverse motion of snow thrower . Auger control lever - used to engage auger motion (throw snow). Discharge chute control lever - used to change the di- rec tion[...]

9 The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your snow thrower or performing any ad just - ments or repairs. We recommend standard safe ty glasses or a wide vision safety mask worn over spectacles. HOW TO USE Y[...]

10 OPERA TION TO THROW SNOW (See Fig. 14) The auger rotation is controlled by the auger control lever located on the right side handle. • Squeeze auger control lever to handle to engage the auger and throw snow . • Release the auger control lever to stop throwing snow . TO MOVE FOR W ARD AND BACKW ARD (See Fig. 16) SELF-PROPELLING, forward and [...]

11 TO ADJUST SKID PLA TES (See Fig. 17) NOTE: The wrench provided in your parts bag may be used to adjust the skid plates. Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow i[...]

12 OPERA TION COLD ST ART - ELECTRIC ST ARTER 1. Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. DO NOT turn the key . Keep the extra safety ignition key in a safe place. 2. Place throttle control in F AST position. 3. Rotate choke control to FULL position. 4. Connect the power cord to the engine. 5. [...]

13 GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in struct ed in this manual. Some ad just - ments will need to be made periodically to properly maintain your snow thrower[...]

14 MAINTENANCE AUGER GEAR CASE • The gear case was fi lled with lubricant to the proper level at the factory . The only time the lubricant needs attention is if service has been performed on the gear case. • If lubricant is required, use only Ronex ED #1 grease. TRACTION DRIVE SYSTEM DO NOT lubricate the drive components inside the snow throwe[...]

15 CAUTION: Do not substitute. Use only original equip ment capscrew/shear bolts as sup plied with your snow thrower . 4. Connect spark plug wire to spark plug. W ARNING: T o avoid serious injury , before performing any service or ad just ments: 1. Be sure throttle is in STOP position. 2. Remove safety ignition key . 3. Make sure the augers and all[...]

16 BEL T KEEPER IDLER ARM SQUARE HOLE BOL T LOCK W ASHER TRACTION DRIVE BEL T CLUTCHING IDLER ARM BRACKET AUGER BEL T FLA T WASHER AUGER PULLEY AUGER HOUSING FRAME ENGINE PULLEY LOCKW ASHER BOL T FIG. 21 SER VICE AND ADJUSTMENTS 1. REMOVE GASOLINE FROM FUEL T ANK - Drain gaso- line from fuel tank into a suitable container , out doors, away from fi[...]

17 SER VICE AND ADJUSTMENTS ST ORAGE Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more. W ARNING: Never store the snow thrower with gaso line in the tank in side a build ing where fumes may reach an open fl ame, spark or pilot light as on a fur nace, water heater , clothes dryer [...]

18 Does not start 1. Fuel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Fill fuel tank. 4. Throttle in STOP position. 4. Move throttle to F AST position. 5. Choke in OFF position. 5. Move to FULL position. 6. [...]

19 SER VICE NOTES[...]

LIMITED W ARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and work man ship. For a period of two (2) years from date of purchase by the original consumer pur- chaser , we will repair or replace, at our option, without charge for parts or labor incurred in repla[...]