Poulan PR1842STC инструкция обслуживания

OWNER'S MANUAL MODEL: PR1842STC LAWN TRACTOR Always Wear Eye Protection During Operation WARNING: Read this Owner's Manual and follow all Warnings and Safety Instructions. Failure to do so can result in serious injury. IMPORTANT MANUAL Do Not Throw Away 183359 3.15.02 RD Printed in U.S.A. 02478[...]

2 Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. SAFETY RULES I. GENERAL OPERATION • Read, understand, and follow all instructions in the manual and on the machine[...]

3 Safe Operation Practices for Ride-On Mowers SAFETY RULES Look for this symbol to point out im- portant safety precautions. It means CAUTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED. CAUTION: In order to prevent acciden- tal starting when setting up, transport- ing, adjusting or making repairs, al- ways disconnect spark plug wire and place wire [...]

4 PRODUCT SPECIFICA TIONS GASOLINE CAPACITY 2.00 GALLONS AND TYPE: UNLEADED REGULAR OIL TYPE (API-SF-SJ): SAE 30 (above 32°F) SAE 5W-30 (below 32°F) OIL CAPACITY: W/FILTER: 3.5 W/O FILTER: 3.0 SPARK PLUG: CHAMPION RC12YC (GAP: .030") GROUND SPEED (MPH): FORWARD: 1st 1.2 2nd 1. 5 3rd 2.4 4th 3.5 5th 4.8 6th 5.3 REVERSE: 1.5 TIRE PRESSURE: FRO[...]

5 (1) Large Flat Washer Steering Wheel Insert Steering Extension Shaft Steering Sleeve Steering Wheel Steering Wheel Adapter (1) Knob (1) Washer 17/32 x 1-3/16 x 12 Gauge Seat (2) Keys Keys Slope Sheet (2) Mulcher Blades (1) Oil Drain Tube For Future Use (1) Hex Bolt 1/4-28 x 1-1/4 (1) Locknut 1/4-28 (1) Locknut 1/2-20 CONTENTS OF HARDW ARE P ACK[...]

6 FIG. 2 ASSEMBL Y TOOLS REQUIRED FOR ASSEMBL Y A socket wrench set will make assembly easier. Standard wrench sizes are listed. (2) 7/16" wrenches Utility knife (2) 3/4" wrenches Tire pressure gauge Pliers When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering whee[...]

7 ASSEMBL Y TO ROLL TRACTOR OFF SKID (See Opera- tion section, page 10, for location and function of controls) • Press lift lever plunger and raise attachment lift lever to its highest position. • Release parking brake by depressing clutch/brake pedal. • Place gearshift lever in neutral (N) position. • Roll tractor forward off skid. • Rem[...]

8 ASSEMBL Y CHECKLIST BEFORE YOU OPERATE AND ENJOY YOUR NEW TRAC- TOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT. PLEASE REVIEW THE FOLLOWING CHECKLIST: ✓ All assembly instructions have been completed. ✓ No remaining loose parts in carton. ✓ Battery is properly prepared and charged. (Mi[...]

9 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. BATTERY CAUTION OR WARNING REVERSE FORWARD FAST SLOW ENGINE ON ENGINE OFF OIL PRESSURE LIGHTS ON FUEL CHOKE MOWER HEIGHT PARKING BRAKE LOCKED UNLOCKED REVERSE NEUTRAL HIGH LOW ATTACHMENT CLUTCH ENGAGED MOWER LIFT DAN[...]

10 OPERA TION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. ATTACHMENT CLUTCH LEVER : Used to engage the mower blades, or other attachment[...]

11 NOTE: Under certain conditions when tractor is standing idle with the engine running, hot engine exhaust gases may cause “browning” of grass. To eliminate this possibility, always stop engine when stopping tractor on grass areas. CAUTION: Always stop tractor com- pletely, as described above, before leav- ing the operator's position; to [...]

12 TO OPERATE ON HILLS CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope. • Choose the slowest speed before starting up or down hills. • Avoid stopping or changing speed on hills. • If slowing is necessary, move throttle control lever to slower position. • If stopping is absolutely necess[...]

13 OPERA TION TO START ENGINE (See Fig. 6) When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine. • Sit on seat in operating position, depress clutch/brake pedal and set parking brake. • Place gear shift lever in neutral (N) position. • Move [...]

14 MOWING TIPS • Mower should be properly leveled for best mowing performance. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trimming. • Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the [...]

15 CUST OMER RESPONSIBILITIES B E F O R E E A C H U S E T R A C T 0 R Inspect Muffler/Spark Arrester Lubrication Chart Check Brake Operation Clean Air Filter Change Engine Oil (with oil filter) Replace Air Filter Paper Cartridge Replace Spark Plug Check Battery Level Check Tire Pressure Clean Battery and Terminals FILL IN DATES AS YOU COMPLETE REGU[...]

16 CUST OMER RESPONSIBILITIES FIG. 12 FIG. 11 BATTERY Your tractor has a battery charging system which is suffi- cient for normal use. However, periodic charging of the battery with an automotive charger will extend its life. • Keep battery and terminals clean. • Keep battery bolts tight. • Keep small vent holes open. • Recharge at 6-10 amp[...]

17 CUST OMER RESPONSIBILITIES V-BELTS Check V-belts for deterioration and wear after 100 hours and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. TRANSAXLE COOLING Keep transaxle free from build-up of dirt and chaff which can restrict cooling. ENGINE LUBRICATION Only use high quality detergent oil[...]

18 CUST OMER RESPONSIBILITIES CLEANING • Clean engine, battery, seat, finish, etc. of all foreign matter. • Keep finished surfaces and wheels free of all gasoline, oil, etc. • Protect painted surfaces with automotive type wax. We do not recommend using a garden hose to clean your tractor unless the electrical system, muffler, air filter and c[...]

19 SER VICE AND ADJUSTMENTS SUSPENSION ARMS RET AINER SPRINGS (BOTH SIDES) RET AINER SPRING ANTI-SW A Y BAR HOUSING GUIDE FRONT LINK COLLAR ENGINE PULLEY LARGE RET AINER SPRING CLUTCH SPRING SMALL RET AINER SPRING BRACKET SQUARE HOLE Fig. 16 TO REMOVE MOWER (See Fig. 16) Mower will be easier to remove from the right side of tractor. • Place attac[...]

20 TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 21) The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake. BELT REMOVAL - • Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual). • Work belt off both mandrel pulleys and idler pulleys. • Pull belt away fr[...]

21 SER VICE AND ADJUSTMENTS FIG. 21 TO ADJUST BRAKE (See Fig. 22) Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle. If tractor requires more than six (6) feet stopping distance at high speed in highest gear on a level dry concrete or paved surface, then brake must be adjusted. • Depress [...]

22 FIG. 26 SER VICE AND ADJUSTMENTS TO ADJUST STEERING WHEEL ALIGNMENT If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual. FRONT WHEEL TOE-IN/CAMBER The front wheel toe-in and camber are not adjusta[...]

23 SER VICE AND ADJUSTMENTS TO REPLACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. • Close hood. INTERLOCKS AND RELAYS Loose or damaged wiring may cause your tractor to run poorly, stop ru[...]

24 ST ORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. CAUTION: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure. TRACT OR Remove mower from trac[...]

25 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly. 2. See “TO START ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug. 4. Replace spark plug. 5. Dirty air filter. 5. Clean/replace air filter. 6. Dirty fuel filter. 6[...]

26 TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Engine continues to run 1 . Faulty operator-safety presence control system. 1. Check wiring, switches and connections. If not when operator leaves seat corrected, contact an authorized service center/ with attachment clutch department. engaged Poor cut - uneven 1. Worn, bent or loose blade. 1. Repl[...]

27 TRACTOR - - MODEL NUMBER PR1842STC SCHEMA TIC BATTERY FUSE IGNITION SWITCH RED RED RED BLACK IGNITION UNIT HEADLIGHTS REMOVABLE CONNECTIONS BLACK BLACK BLACK WHITE WHITE WHITE RED BLACK ORANGE BLACK BROWN BLACK BLACK BLACK STARTER M SEAT SWITCH (NOT OCCUPIED) GROUNDING CONNECTOR ATT'MENT CLUTCH (CLUTCH OFF) CLUTCH / BRAKE (PEDAL UP) SOLENOI[...]

28 REP AIR P ARTS TRACTOR - - MODEL NUMBER PR1842STC ELECTRICAL 28 29 26 24 42 43 27 27 25 41 27 27 40 33 90 30 8 2 1 27 D . C . A M P E R E S 45 16 22 21 52 16[...]

29 KEY P A RT N O . N O . DESCRIPTION 1 163465 Battery 2 74760412 B ol t Hex Hd 1/4-20unc X 3/4 8 176689 Battery Box 1 6 176138 S w i tch Interlock Push-In 2 1 175685 H arness Socket Light 2 2 4152J Bu lb , L ig ht # 1156 2 4 4799J Cable Battery 2 5 146147 Cable Battery 6 Ga Red w/16 wire 2 6 175158 Fuse 2 7 73510400 N u t Keps Hex 1/4-20 Unc 2 8 4[...]

30 26 25 58 219 20 219 23 64 208 13 208 11 1 3 2 9 208 208 5 5 207 3 3 3 142 17 29 28 12 51 57 53 52 54 55 145 37 3 37 24 26 25 3 31 24 30 35 3 26 33 10 26 34 35 18 14 38 14 206 212 159 3 115 3 142 211 114 REP AIR P ARTS TRACTOR - - MODEL NUMBER PR1842STC CHASSIS AND ENCLOSURES[...]

31 REP AIR P ARTS TRACTOR - - MODEL NUMBER PR1842STC CHASSIS AND ENCLOSURES KEY P A RT N O . N O . DESCRIPTION 1 174619 C hassis 2 176554 Drawbar 3 17060612 Screw 3/8-16x.75 5 155272 B um per Hood/Dash 9 168337X012 Dash P/L 1 0 72140608 B o lt C a rriage 3/8-16 x 1 1 1 174996 Panel Dash Lh 1 2 145660 C l ip Ti nnerman 1 3 172105X010 Panel Dash Rh 1[...]

32 29 28 112 14 41 38 39 57 51 74 75 78 76 77 1 25 19 24 2 53 35 34 37 36 35 62 36 59 212 55 77 61 22 27 26 6 113 18 51 5 18 6 85 52 30 32 32 30 52 11 85 80 4 3 13 81 84 82 64 65 145 79 16 96 26 27 51 48 150 151 202 49 47 50 120 21 8 10 156 165 168 166 163 14 159 161 198 158 164 83 162 169 89 197 6 170 66 56 63 116 70 69 26 REP AIR P ARTS TRACTOR -[...]

33 REP AIR P ARTS TRACTOR - - MODEL NUMBER PR1842STC DRIVE KEY P A RT N O . N O . DESCRIPTION KE Y PART NO. N O. DESCRIPTION 1 - - - - - - Transaxle Peerless (206-545C) (Order parts from transaxle manufacturer) 2 146682 S p ri n g R et u r n B r a ke T / a Z i n c 3 123666X P ul l ey Tr ansaxle 18" tires 4 12000028 R ing Retainer # 5100-62 5 1[...]

34 5 5 4 3 43 6 43 8 10 40 32 11 8 6 87 46 46 8 6 87 29 88 71 17 43 91 2 1 41 42 37 36 37 38 12 39 44 51 54 33 35 34 68 67 67 67 13 65 68 15 15 15 29 29 82 REP AIR P ARTS TRACTOR - - MODEL NUMBER PR1842STC STEERING ASSEMBL Y[...]

35 REP AIR P ARTS TRACTOR - - MODEL NUMBER PR1842STC STEERING ASSEMBL Y KEY P ART N O . N O . DESCRIPTION 1 180656 Wheel Steering 2 172393 A x l e A s m Cast Iron LT 3 169840 S pindle Asm LH 4 169839 S pindle Asm RH 5 6266H B earing Race Thrust Harden 6 121748X W asher 25/32 X 1-5/8 X 16 Ga 8 12000029 R ing Klip #t5304-75 1 0 175121 Link Drag 1 1 1[...]

36 REP AIR P ARTS TRACTOR - - MODEL NUMBER PR1842STC SEA T ASSEMBL Y 1 171683 Seat 2 140551 Bracket Pivot Seat 8 720 3 71110616 B o l t F i n Hex 3/8-16 Unc X 1 4 19131610 W asher 13/32 X 1 X 10 Ga 5 145006 C lip Push-In 6 73800600 N u t H e x w / I n s . 3 / 8 - 1 6 U n c 7 124181X S pring Seat Cprsn 2 250 Blk Zi 8 17000616 S crew 3/8-16 X 1.5 9 1[...]

37 REP AIR P ARTS TRACTOR - - MODEL NUMBER PR1842STC DECALS NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm KEY P A RT N O . N O . DESCRIPTION 6 2 1 5,8 4,10 3,9 11 7 WHEELS AND TIRES KEY P A RT N O . N O . DESCRIPTION KEY P A RT N O . N O . DESCRIPTION 10 3 16 9 1 59192 C a p V alve Tire 2 65139 S t e m V a l v e 3 170455 T i [...]

38 2 1 OPTIONAL EQUIPMENT Spark Arrester 29 44 46 32 31 33 37 33 62 13 4 72 78 81 3 16 78 23 45 14 38 40 41 112 REP AIR P ARTS TRACTOR - - MODEL NUMBER PR1842STC ENGINE[...]

39 REP AIR P ARTS TRACTOR - - MODEL NUMBER PR1842STC ENGINE KEY P A RT N O . N O . DESCRIPTION NOTE: All component dimensions given in U. S. inches 1 inch = 25.4 mm 1 170551 Control Th/ch Flag 2 17720408 S c r e w Hex Thd Cut 1/4-20 x 1/2 3 - - - - - - - - Engine, Briggs Model 31H777 (Order Parts From Engine Manufacturer) 4 137352 M u ffler 1 3 165[...]

40 REP AIR P ARTS TRACTOR - - MODEL NUMBER PR1842STC MOWER DECK 15 14 13 11 10 9 8 16 68 37 30 31 32 33 146 148 145 150 45 144 147 147 142 149 142 49 50 51 54 52 53 55 56 34 1 46 44 21 24 25 26 27 2 28 29 23 21 21 21 18 18 20 2 48 59 19 4 3 5 6 21 40 143 36 40 37 40 159 152 151 153 154 157 158 67 153 156 155 132 91 94 182 95 183 132 113 117 116 118[...]

41 KEY P A RT N O . N O . DESCRIPTION KEY P A RT N O . N O . DESCRIPTION 1 165892X421 M o w e r D eck Assembly, 42" 2 72140506 B o l t 3 138017 Bracket Asm Fr. Sway Bar 3/42 4 165460 B r acket Asm Deck 42" Sway Bar 5 4939M R e t a i n e r S p ri n g 6 178024 B a r Sway Deck 8 850857 B o l t 3 / 8-24 x 25 Grade 8 patched 9 10030600 W asher[...]

42 36 15 20 16 17 18 20 20 15 20 4 5 6 2 3 1 6 5 4 7 8 37 41 40 38 12 11 31 32 31 32 19 19 13 13 13 13 REP AIR P ARTS TRACTOR - - MODEL NUMBER PR1842STC MOWER LIFT[...]

43 REP AIR P ARTS TRACTOR - - MODEL NUMBER PR1842STC MOWER LIFT 1 159460 W i r e Asm Inner/Sprg W/plunger LT 2 159471 Shaft Asm Lift RH w/Inf 3 105767X P i n G roove 1 500 Zinc 4 12000002 E R i n g #5133-62 5 19211621 W asher 21/32 X 1 X 21 Ga 6 120183X Bearing Nylon Blk 629 Id 7 125631X G r ip Handle 8 170770 B u t t o n P l unger Yellow 1 1 13986[...]

44 NOTES[...]

45 LIMITED WARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and workmanship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or replace, at our option, without charge for parts or labor incurred in replacin[...]

46 T E C U M S E H ® Issued January 1980 Revised January 1991 T E C U M S E H ® POLICY LIMITED WARRANTIES FOR NEW PEERLESS GEAR POWER TRAIN COMPONENTS A. Products Warranted Peerless Gear and Machine Division of Tecumseh Products Company (“Tecumseh”), subject to the limitations contained below, will,at its option, repair or replace, without ch[...]

47 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to preven[...]

Your POULAN PRO product has been expertly engineered and carefully manufactured to rigid quality standards. As with all mechanical products, some adjustments or part replacement may be necessary during the life of your unit. FOR SERVICE OR REPLACEMENT PARTS: 1. Consult your dealer/place of purchase. 2. Consult the yellow pages of your phone directo[...]