Precision Power MaxxBass инструкция обслуживания

Maxx Bass ®[...]

T ABLE OF CONTENTS Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Ser vice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Wh y Use Maxx Bass ® . . . . . . .[...]

CONGRA TULA TIONS Thank you f or choosing Precision P o wer TM audio equipment. At Precision P o wer TM we proudly design, engineer and manuf acture audio products f or after market car audio . Our aw ard winning engineering team utilizes innov ativ e technology to consistently deliv er Absolutely State of the Ar t performance, sound quality , reli[...]

WHY USE MAXXB ASS Precision P ower TM will introduce the first Maxx Bass ® processor to the automotiv e market. The Maxx Bass ® processor is ideal f or improving the perceiv ed bass response in door mounted speakers without upgrading the speak ers or amplifiers. Maxx Bass ® provides subw oof er like perf or mance with perceived bass response to [...]

MaxxBass uses psychoacoustics to e xtend the perceiv ed bass frequency response.  It is prov en to provide up to 1.5 octav es of increased bass range .  It does not change the frequency balance of the music and sounds more natural than large bass boosts .  It does not require more amplifier pow er and speaker e xcursion.  It has been pr[...]

5 HO W DOES MAXXBASS WORK Maxx Bass ® uses adv anced digital signal processing based on the prov en psychoacoustic Phenomenon of the Missing Fundamental. A basic description and a Maxx Bass ® Signal Flow diag ram are provided f or interested users. MaxxBass ® first implements a crossov er at the Maxx Bass ® F requency . The Maxx Bass ® Process[...]

MAXXB ASS SIGNAL FLO W FEA TURES  Selectable Maxx Bass ® F requency Setting of 60Hz and 80Hz  Green LED clip/Red LED power indicator signal  Gold 2 Channel in/2 channel buff ered full-range out RCA connectors  4-pin locking pow er plug  Input connector for outboard Maxx Bass ® Intensity controller  Remote and on-box intensity co[...]

SPECIFICA TIONS F requency 20hz-20kHz Signal-to-Noise Ratio >85dB Separation 65dB @ 1kHz Crossov er Slope 24dB/octav e Input Impedance 20,000 Ohms Input Sensitivity v ariable , 300mV to 3V peak to peak Output Lev el v ariable , 300mV to 5V peak to peak Supply V oltage 9 to 16 VDC INST ALLA TION/MOUNTING NO TE: As an option, before beginning, dis[...]

MASSB ASS OUTLINE AND DIMENSIONS MI NM A X I N TEN SI TY MI NM A X OU T P UT I NP UT MI NM A X 80H z 60H z ON OF F F RE Q UE NCY CROS S O VER I NP UT OUT P U T P OW E R RE M OT E G ND RE M +12V RE M OU T ( 11. 5 cm ) ( 6. 3 cm ) ( 14 cm ) ( 3 cm ) 1. 18 i n 2. 48 i n 4. 53 i n 5. 51 i n ( 15 cm ) 5. 90 i n PO W ER CL I P 8[...]

WIRING CONFIGURA TIONS The Maxx Bass ® Processor is recommended in two diff erent configurations . 1. Front Stereo Configuration The figure below illustr ates the wiring for a front stereo configuration. One Maxx Bass ® Processor is used between the front channel source and front speaker amplifier to increase the bass response only on the front s[...]

2. Dual Stereo Configurations F or systems without rear subwoof ers, the user ma y pref er to use two Maxx Bass ® Processors, one f or the front speakers and one f or the rear speakers . The units should be wired between the in-dash CD Receiv er and the power amplifiers as sho wn below . NO TE: As an option, before beginning, disconnect the negati[...]

The ground wire should be of the same gauge wire as the po wer wire. As a rule of thumb , use as shor t length of wire as possible . Find a location near the Maxx Bass ® Processor that is metal ( the floor is ideal) and clean an area about the size of a quar ter to bare metal. Drill a pilot hole in the middle of this area. T er minate the wire wit[...]

INPUT T o use Speak er Le vel Inputs (common g round head units only), connect RCA plugs to the front or rear speaker leads as sho wn. NO TE: It is impor tant to connect an input signal to both RCA input jacks if a stereo amplifier is used, otherwise the connected channel receiv es full range and the disconnected channel will receiv e only the har [...]

MAXXB ASS PROCESSOR SETTINGS T o achie ve proper perf or mance it is impor tant to set or tune the settings on the Maxx Bass ® Processor to the final system. This section recommends initial settings and the users can then fur ther adjust these f or optimal listening. 1. CROSSO VER: The CROSSO VER control implements a - 24dB/octav e low pass filter[...]

When the Remote INTENSITY control is plugged into the Maxx Bass ® Processor , the Remote INTENSITY control become activ e and the INTENSITY control on the Maxx Bass ® Processor is disabled. This allows the user to install a remote control in a location diff erent than the Maxx Bass ® Processor and place in a more conv enient position for the lis[...]

SOUND IN ONE CHANNEL ONL Y Re v erse left and right RCA outputs for one band (i.e .-subwoof ers) SOUND IS NO W IN OPPOSITE CHANNEL SAME CHANNEL Re v erse RCA inputs Problem is in the amplifier , Speakers , or associated wiring of the silent channel. SOUND IS NO W IN OPPOSITE CHANNEL SAME CHANNEL Re v erse RCAs to head unit Problem is in the Crosso [...]

LIMITED TWO YEAR CONSUMER W ARRANTY : Directed Electronics, Inc. promises to the original purchaser , to replace this product should it prov e to be def ective in w orkmanship or mater ial under normal use, f or a period of two y ears from the date of purchase b y the dealer as indicated by the date code marking of the product PRO VIDED the product[...]