Rangemaster CLAHDC120BB инструкция обслуживания

Users Guide & Installation Instructions[...]

IMPORT ANT SAFETY INFORMA TION Installation Page 2 Child Safety 2 Maintenance and Service 3 YOUR APPLIANCE 4 OPERA TING INSTRUCTIONS Cooker Hood Controls 4 Worktop Lighting 4 Fan 4 T o Operate 5 Recirculation 5 Extraction 5 MAINTENANCE AND CLEANING Cleaning 6 Metal Grease Filters 6 Charcoal Filters 7 T o Remove/Replace the Charcoal Filters 7 T o Re[...]

• INST ALLA TION • Any installation work must be underaken by a qualified electrician or a competent person. • This hood must be installed in accordance with the installation instructions and all measurements must be adhered to. • If the cooker hood is installed for use above a gas appliance then the provision for ventilation must be in acc[...]

• MAINTENANCE AND SERVICE • This appliance can be a hazard if the grease filters and charcoal filters are not cleaned and replaced as recommended. • Always insist on genuine RANGEmaster spare parts. • Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by inexperienced persons may cause injury or [...]

The chimney hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. The appliance can be installed to recirculate or extract contaminated air . COOKER HOOD CONTROLS The chimney hood functions are controlled by three manual slide switches located on the right, on the underside of the canopy . WORKT OP LIGHTING The [...]

TO OPERA TE Select the required fan speed and light if required. RECIRCULA TION In the recirculation mode contaminated air enters the chimney hood through the grease filter cassettes. The air is cleaned by the charcoal filters and leaves through the grilles in either side of the chimney stack. EXTRACTION In the extraction mode the contaminated air [...]

Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply . CLEANING We recommend the chimney hood is cleaned using a damp cloth wrung out in warm soapy water using a mild liquid household cleaner . Never use excessive amounts of water when cleaning, in particular around the control panel. Never use thinners or p[...]

CHARCOAL FIL TERS (2) In the recirulation mode the activated charcoal filters absorb smells and unwanted odours. The charcoal filters cannot be cleaned or regenerated and must be replaced every four months, or more frequently if the hood is used consistently over 4 hours per day . T o remove the charcoal filters, first remove the metal grease filte[...]

TECHNICAL INFORMA TION DIMENSIONS CANOPY : Height 240mm Width (60cm version) 598mm (90cm version) 898mm (120cm version) 1 198mm Depth 490mm CHIMNEY : Height (Upper Section) 415mm (Lower Section) 560mm ELECTRICAL SUPPL Y VOL T AGE: (50Hz) 230V POWER CONSUMPTION: 225W F AN MOTOR: 145W LIGHT BULB: 2 x 40W 80W PERFORMANCE SPEEDS 3 CAP ACITY m 3 /h* 410[...]

ELECTRICAL CONNECTION THIS APPLIANCE MUST BE EARTHED ELECTRICAL REQUIREMENTS Any permanent electrical installation must comply with the latest I.E.E. Regulations and local Electricity Board regulations. For your own safety this should be undertaken by a qualified electrician e.g. your local Electricity Board, or a contractor who is on the roll of t[...]

INST ALLA TION REQUIREMENTS Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown. All installations must comply with the local authorities requirements for the discharge of exhaust air . Incorrect installation may affect the safety of this cooker hood. Before installation check the wa[...]

INST ALLING THE CHIMNEY HOOD CLEARANCE HEIGHTS The chimney hood is designed to be fitted over a cooking appliance. A minimum clearance height of 650mm (25˚ins) is required when installed above a built-in electric hob, or 700mm (27˚ins) when installed above a built-in gas hob. When installed between adjoining wall cabinets, the wall cabinets must [...]

Note: If the hood is to be installed onto a hollow construction or plaster or partition board wall then special fixing screws will be required (not supplied). FITTING THE CANOPY HOOD 1. Rotate the adjusting screws (R) on the canopy (C) to about halfway . 2. Hook the canopy (C), onto the wall fixing bracket (1) and push down until the canopy adjusti[...]

RECIRCULA TION If you are using the hood for recirculation, ensure the charcoal filters are in position following the instructions contained in the section “T o Remove/Replace the Charcoal Filters”. Note: When the hood is used in the recirculation mode ensure that the plate (T) has been fixed into the lower chimney section. If not, fit the plat[...]

INST ALLING THE CHIMNEY HOOD FITTING THE FRONT RAIL These instructions apply to models as follows: - CLAHDC60BB/ CLAHDC90BB/, CLAHDC90BC/ CLAHDC120BB/, CLAHDC120BC/ Do not fit the front rail until the chimney hood is mounted on the wall. 1. Use a 4mm Allen key to fix the mounting brackets to the front of the canopy using the screws provided. 2. Use[...]

4329641 02 020412[...]