Regency L234-NG инструкция обслуживания

FPI FIREPLACE PRODUCTS INTERNA TIONAL L TD. 6988 V enture St., Delta, BC, Canada V4G 1H4 918-667a W ARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury , property damage, or loss of life. Refer to this manual. For assistance or additional information consult an authorized installer , service agency or the [...]

Regency ® L234 Direct V ent Gas Insert 2 REGENCY GAS FIREPLACE INSERT TO THE NEW OWNER Congratulations! Y ou are the owner of a state-of-the-art Gas Insert by FPI. The L234 Direct V ent Gas Insert has been designed to provide you with all the warmth and charm of a fi replace, at the fl ick of a switch. The L234-NG and L234-LP have been approved [...]

Regency ® L234 Direct V ent Gas Insert 3 T ABLE OF CONTENTS SAFETY LABEL Safety Label .................................................................. 4 REQUIREMENTS MA Code - CO Detector (for the State of Massachusetts only) ............................ 5 UNIT DIMENSIONS Unit & Faceplate Dimensions ....................................... 6 [...]

Regency ® L234 Direct V ent Gas Insert 4 INST ALLA TION SAFETY LABEL This is a copy of the labels that accompany each L234 Gas Insert. We have printed a copy of the contents here for your review . The safety label is located on a plate inside the base of the unit visible when the bottom louver is opened. Ensure that the safety label is attached to[...]

Regency ® L234 Direct V ent Gas Insert 5 INST ALLA TION REQUIREMENTS 5.08: Modifica tions to NFPA-54, Chapter 10 (2) Revise 10.8. 3 by adding the follow ing additiona l requirements: (a) For all side wall hor izontally vente d gas fueled equipm ent installed in every dwellin g, building or struc ture used in whole or in part for residential pu rpo[...]

Regency ® L234 Direct V ent Gas Insert 6 INST ALLA TION UNIT & F ACEPLA TE DIMENSIONS[...]

Regency ® L234 Direct V ent Gas Insert 7 INST ALLA TION INST ALLA TION IMPORT ANT MESSAGE SA VE THESE INSTRUCTIONS The FPI Direct V ent Gas Insert must be installed in accordance with these instructions. Carefully read all the instructions in this manual fi rst. Con- sult the building authority having jurisdiction to determine the need for a perm[...]

Regency ® L234 Direct V ent Gas Insert 8 INST ALLA TION INST ALLA TION 11 ) Due to high temperatures, the appliance should be located out of high traffi c areas and away from furniture and draperies. Children and adults should be alerted to the hazards of high surface temperatures, especially the fi replace glass, and should stay away to avoid b[...]

Regency ® L234 Direct V ent Gas Insert 9 INST ALLA TION INST ALLA TION MINIMUM CLEARANCES T O COMBUSTIBLES Side W alls A 8" (203 mm)* Ceiling B 56" (1422 mm) Min. Mantel Height C 21" (533 mm) see Diagram 1 Max. Mantel Depth D 12" (305 mm) see Diagram 1 Alcove Width E 60" (1524 mm) Alcove Depth F 36" (914 mm) Hearth He[...]

Regency ® L234 Direct V ent Gas Insert 10 INST ALLA TION THE APPLIANCE MUST NOT BE CONNECTED TO A CHIMNEY FLUE SERVING A SEP ARA TE SOLID FUEL BURNING APPLIANCE. This appliance is designed to be attached to two 3" (76mm) co-linear aluminium fl ex running the full length of the chimney . The fl ue length must be a minimum length of 8' ([...]

Regency ® L234 Direct V ent Gas Insert 11 INST ALLA TION CONVERTING FROM 3" & 3" VENTING TO 3" & 2" 1) Remove the top plate from the unit by undoing the screw at the front of the fi rebox and slide out towards the back of the unit. VENT RESTRICT OR POSITION The V ent Restrictor plate is located on the inside top of the[...]

Regency ® L234 Direct V ent Gas Insert 12 INST ALLA TION GAS INSERT AERA TION SYSTEM The burner aeration is factory set but may need adjusting due to either the local gas supply or altitude. Open the air shutter for a blue fl ame or close for a more yellow fl ame. GAS CONNECTION GAS CONNECTION W ARNING: Only persons licensed to work with gas pip[...]

Regency ® L234 Direct V ent Gas Insert 13 INST ALLA TION GAS PIPE PRESSURE TESTING The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve dur in g a ny pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig. (3 .4 5 kPa). Disconnect piping from val[...]

Regency ® L234 Direct V ent Gas Insert 14 INST ALLA TION CONVERSION KIT #536-969 FROM NG T O LP INST ALLA TION LP Conversion Kit Contains: Qty . Part # Description 1 910-037 LP Pilot Orifi ce 1 904-163 Orifi ce #54 1 904-529 5/32" Allen Key 1 918-590 LP Conversion Decal 1 908-528 Red Propane Label 1 918-688 Instruction Sheet THIS CONVERSION[...]

Regency ® L234 Direct V ent Gas Insert 15 INST ALLA TION INST ALLA TION 9) Remove burner orifi ce with a 1/2" wrench and discard. 10) Install the new LP burner orifi ce stamped #54 and tighten. 11 ) Pull of f the pilot cap to expose the pilot orifi ce. 12) Unscrew the pilot orifi ce with the supplied allen key and replace it with the LP p[...]

Regency ® L234 Direct V ent Gas Insert 16 INST ALLA TION OPTIONAL BRICK P ANEL INST ALLA TION 1) Carefully remove the brick panels from the box and unwrap them. 2) Insert the back brick panel by carefully placing it against the back wall of the fi rebox and rest it on the rear log tray . Back Brick Panel Rear Log T ray 3) Slide the right side bri[...]

Regency ® L234 Direct V ent Gas Insert 17 INST ALLA TION CONT OUR OR CONTEMPORAR Y F ACEPLA TE Faceplate Contents List: 1 Faceplate (Contour or Contemporary) 1 Louver (Contour or Contemporary) 4 Screws (10-24 x 1/2" Pan Head Phillips Black) 2 Wire Clips 1 Cable T ie Faceplate Installation: 1) Place the 4 10-24 x 1/2" screws into the face[...]

Regency ® L234 Direct V ent Gas Insert 18 INST ALLA TION 7) From the right side of the unit connect the black electrode wire to the DC Sparker as shown in diagram 6. Electrode Wire 8) Secure the loose wires into the wire clips above and to the bottom left of the DC Sparker as shown in diagram 7. 11 ) Remove the grommet from the bracket on the left[...]

Regency ® L234 Direct V ent Gas Insert 19 INST ALLA TION 13) Tuck the wires completely into the sleeve and place the supplied cable tie to the end of it as shown in diagram 1 1. Diagram 1 1 14) Place the grommet removed from step 10 over the sleeve (see diagram 12) and put back in place (see diagram 13). NOTE: Ensure connectors are tucked in behin[...]

Regency ® L234 Direct V ent Gas Insert 20 INST ALLA TION OPTIONAL BACKING PLA TE 3) Attach the top piece of the backing plate to the faceplate using 5 screws provided as shown in diagram 1. Rear View of Faceplate Attach Faceplate & T op Backing Plate to Unit 4) Place the 4 10-24 x 1/2" screws into the faceplate mounting brackets as identi[...]

Regency ® L234 Direct V ent Gas Insert 21 INST ALLA TION Attach Left & Right Backing Plate to Faceplate 7) Align the screw holes on the left and right side backing plate with the oblong openings in the faceplate and secure in place using a minimum of 2 screws on each side as shown in diagram 4. Faceplate shown on unit without left and right si[...]

Regency ® L234 Direct V ent Gas Insert 22 INST ALLA TION OPTIONAL HEARTH TRIM 1) Open the left and right side faceplate panels. 2) Align the screw holes on the hearth trim with the screw holes on the fl anges on the left and right side faceplate. Secure in place using 2 screws on each side as shown in diagram 1. 3) Close the left and right side f[...]

Regency ® L234 Direct V ent Gas Insert 23 INST ALLA TION LOG SET INST ALLA TION Log kit (Part # 536-930) contains the following pieces: a) 2-71 1 Rear Log b) 2-712 Center Log c) 2-713 Left Log d) 2-714 Front Log e) 2-715 T op Left Log f) 2-716 T op Right Log g) Embers (supplied with packaged manual) h) 946-669 Platinum Embers (supplied with packag[...]

Regency ® L234 Direct V ent Gas Insert 24 INST ALLA TION 5) Fit the left side of log 2-713 into the pin on log 2-714 and rest the right side of the log on the burner plate pushing it against the tab. 2-712 2-713 2-714 2-713 6) Place log 2-715 into the pin on log 2-712 and rest the right end of the log on the notch in log 2-713. 2-715 2-712 Notch 2[...]

Regency ® L234 Direct V ent Gas Insert 25 INST ALLA TION 7) Place embers on the right side of the burner as shown. 8) Fit log 2-716 into the pin on log 2-712. Right side of Burner 2-713 2-716 2-712 Also place a few embers along the burner tube next to log 2-713. Separate platinum embers and place on and around the embers. Avoid stacking platinum e[...]

Regency ® L234 Direct V ent Gas Insert 26 INST ALLA TION Completed Log Set Installation 2-71 1 2-716 2-715 2-712 2-713 2-714 INST ALLA TION[...]

Regency ® L234 Direct V ent Gas Insert 27 INST ALLA TION WIRING DIAGRAMS This heater does not require a 120V A.C. supply for operation. However , a 120V A.C. power supply is needed for the fan/blower operation. Caution: Ensure that the wires do not touch any hot surfaces and are away from sharp edges. W ARNING: Electrical Grounding Instructions Th[...]

Regency ® L234 Direct V ent Gas Insert 28 INST ALLA TION INST ALLA TION Use of FPI Remote Control Kit #910-399 or #910-368 is approved for this unit. Use of other systems may void your warranty . The remote control kit comes with a hand held transmitter , a receiver and a wall mounting plate. OPTIONAL REMOTE CONTROL OPTIONAL W ALL THERMOST A T A w[...]

Regency ® L234 Direct V ent Gas Insert 29 OPERA TION OPERA TING INSTRUCTIONS IMPORT ANT : Gas on/off knob cannot be turned from "PILOT" to "OFF" unless it is partially depressed. 1) Turn burner OFF using "ON/OFF" switch. 2) T urn gas control knob so indicator points to "OFF" position and allow 5 minutes for [...]

Regency ® L234 Direct V ent Gas Insert 30 OPERA TION OPERA TING INSTRUCTIONS COPY OF LIGHTING INSTRUCTION PLA TE AUT OMA TIC CONVECTION F AN OPERA TION The fan operates automatically . T urn the knob on the left side of the faceplate to adjust to the desired speed. The fan will turn on as the insert comes up to operating temperature. After the uni[...]

Regency ® L234 Direct V ent Gas Insert 31 MAINTENANCE MAINTENANCE 2) Remove the T ermination Cap, and shine a fl ashlight down the V ent. Remove any bird nests, or other foreign material. 3) Check for evidences of excessive condensation, such as water droplets forming in the inner liner , and subsequently dripping out the joints. Continuous conde[...]

Regency ® L234 Direct V ent Gas Insert 32 MAINTENANCE MAINTENANCE F AN REPLACEMENT 1) Unplug the power source. 2) Open the left and right side faceplate panels. 3) Remove the bottom louver by pulling out. 4) Remove the glass door . a) Pull off the left side spring hook that holds the door in place. While holding the hook turn it upside down and pl[...]

Regency ® L234 Direct V ent Gas Insert 33 MAINTENANCE MAINTENANCE 11 ) Unplug the fan connector wires. 12) Remove the 2 screws that hold the fan bracket in place. 13) Remove the fan by sliding the fan forward and lift up and out. 14) Remove the ground screw which holds the ground wire. Ground Wire 15) Replace the fan. NOTE: Bend the connector clip[...]

Regency ® L234 Direct V ent Gas Insert 34 MAINTENANCE MAINTENANCE V AL VE REPLACEMENT 1) Open the left and right side faceplate panels. 2) Remove the bottom louver by pulling out. 3) Remove the glass door . a) Pull off the left side spring hook that holds the door in place. While holding the hook turn it upside down and place it into the middle op[...]

Regency ® L234 Direct V ent Gas Insert 35 MAINTENANCE MAINTENANCE 13) Remove the rear log tray by undoing the 3 screws. Rear Log T ray Removed 14) Remove the 12 screws that hold the valve tray to the fi rebox and carefully pull out. 15) Replace the valve. 16) Reverse steps 14 - 1. 11 ) Remove the burner by undoing the 3 screws. 12) Remove the bur[...]

Regency ® L234 Direct V ent Gas Insert 36 P AR TS LIST P ARTS LIST MAIN ASSEMBL Y Part # Description Part # Description 1) 940-355/P Glass 536-539 Door Frame Assembly 536-540 Door Frame Assembly with Glass 2) 948-463 Burner Assy - NG/LP 3) 536-092 Log T ray Middle 4) 536-014 Log T ray Rear 5) 536-01 1 Fan Access Plate 6) 536-107 Gasket - Fan Acces[...]

Regency ® L234 Direct V ent Gas Insert 37 P AR TS LIST P ARTS LIST F ACEPLA TE ASSEMBL Y Part # Description 60) 536-918 Contemporary Faceplate 61) 536-914 Contour Faceplate 62) 910-246 Burner ON/OFF Switch 63) 910-330 Fan Speed Control 120 V 64) 904-569 Fan Speed Control Knob 65) 536-125 Fan Switch Bracket 66) 948-216 Regency ® Logo[...]

Regency ® L234 Direct V ent Gas Insert 38 P AR TS LIST P ARTS LIST BACKING PLA TE & HEARTH TRIM ASSEMBL Y Part # Description 536-922 Backing Plate 81) * Left Side 82) * Right Side 83) * T op 84) * Left Corner 85) * Right Corner 536-940 Hearth Trim 86) * T op 87) * Bottom * Not available as a replacement part.[...]

Regency ® L234 Direct V ent Gas Insert 39 W ARRANTY Regency Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance T eam carefully inspects each unit thoroughly before it leaves our facility . FPI Fireplace Products International Ltd. is pleased to extend this limited lifetime warranty [...]

Installer: Please complete the following information Dealer Name & Address: ______________________________________________ ___________________________________________________________________ Installer: ___________________________________________________________ Phone #: ___________________________________________________________ Date Installed:[...]