Renesas HS7144ECH61H инструкция обслуживания

2004.1.29 SH7144 Gro up FP-112 B User System Interfa ce Board HS7144ECH61H User’s Manual Renesas M icrocomput er Developm ent Envir onment System SuperH TM Family /SH7144 S eries Rev.4. 00[...]

Cautions Keep safety first in your circ uit designs ! 1. Renesas Technology Corp. put s the maxi mum effort into maki ng semiconduct or product s better and more reliable, but the re is always the possi bility that trouble may occur with them. Trouble with semi conductors may lead to personal injury, fi re or propert y damage. Remember to give due [...]

I IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this u ser system interface cable. • KEEP the user's manual handy for future reference. Do not atte m pt to use the user system interface ca ble unt il y ou fully understa nd it s mec ha ni s m. User Syst em Interface Cable: Throughout thi s document, the ter m [...]

II LIMITED WARRANTY Renesas warrants its user system interface cabl es to be manufactured in accordance with published specifications and free from defects in material and/or workmanship. Renesas will re pair or replace any user system interfac e cables determine d to be defective in ma terial and/or workmanship. User s ystem interface cables are w[...]

III State Law: Some states do not allo w the exclusion or limitatio n of implied warranties or liabilit y for incidental o r consequential d amages, so t he ab o ve limitation or excl usion ma y not appl y to you. This warr ant y give s yo u spec if ic lega l rig hts, and you ma y have ot her rig hts wh ic h may va ry fro m state to state. The Warr[...]

IV SAFETY PAGE READ FIRST • READ this user's manual before using this u ser system interface cable. • KEEP the user's manual handy for future reference. Do not atte m pt to use the user system interface ca ble unt il y ou fully understa nd it s mec ha ni s m. DEFINITION OF SI GNAL WORDS This is the safet y alert symbol. It is used to [...]

V W ARNING Observe the pr ecautions listed below. Failur e to do so will result in a FIRE HA ZARD and will damag e the user system and the emula tor product or will r esult in PERSONAL INJURY. Th e USER PROGRAM will be LOST. 1. Do not repair or remodel the emulator product b y yourself for e lectric sho ck prevention and quality assurance. 2. Alway[...]

i Preface The HS7144ECH61H is a u ser sy stem interface board th at connects a u ser sy stem for the SH7144 FP-112B packag e to the SH 7046 E6000H emu lator (HS7046EPH60H).[...]

ii Contents Section 1 Configuration ..................................................................................... 1 Section 2 Environmental Conditions ................................................................. 3 2.1 Setting Operating Voltage and Operating Frequency ....................................................... 3 Section 3 P[...]

1 Section 1 Configuration Figure 1 and table 1 sh ow th e config uration and com ponents of the user sy stem interface board f or the FP-112B pack age. Please m ake s ure you have all of thes e compon ents w hen unpackin g. Socket cover Screws (M2.0 x 8 mm) with flat washers EV-chip board Board User system Spacer IC socket Screws (M2.0 x 12 mm) wit[...]

2 CAUTION Use an IC149-112C 15333-0B socket (m anufactured by YAMAICH I ELECTRONICS Co., Lt d.) for the FP- 112B package IC socket on the user syst em. Table 1 HS7144ECH61H Compon ents No. Component Quantity Remarks 1 Board 1 With two spacers (2.6MP x 6 m m) 2 IC socket 1 For the FP-112B package (to be mounted on the user system) 3 Socket cover 1 F[...]

3 Section 2 Environmental Conditions Maintain the condit ions in table 2 when us ing the emulator. Table 2 Environmental Condit ions Item Specifications Temperature Operating: +10 to +35°C Storage: -10 to +35°C Humidity Operating: 35 to 80% RH, no condensation Storage: 35 to 80% RH, no condensation Vibration Operating: 2.45 m/s m ax. Storage: 4.9[...]

4 Section 3 Product Specifications The specifications of this product are s hown in table 3. Table 3 Product Specifications Item Specifications Target processor SH7144F Package FP-112B Function Level limitation: This function keeps the output signal from 3-V emulator system equal to or less than power supply voltage of the user system (Vcc). User-s[...]

5 Section 4 User Interface Specifications The user system interface board incorporates a level convers ion circuit supporting a low-voltage circuit. Accordingl y, when connecting the user sys tem to the emulator, pay att ention to the signal delays and the number of FANINs and FANOUTs. 4.1 User System Interface Circu it The user system interface ci[...]

6 (3) AVcc and AN7 to AN0 AN7 to AN0 Vss A Vss Emulator User system QS3384 5Vcc Figure 5 User System Interface Circuit for AVcc and AN7 to AN0[...]

7 Section 5 Connection Procedures 5.1 Connectin g User System Interface Board to User S ystem W ARNING Always switch OFF the user syst em and the emulator product before the USER SYSTEM INTERFACE BOARD is connected to or removed from any part . Before connecting, make sure that pin 1 on bot h sides are correctly aligned. Failure to do so will resul[...]

8 5.1.2 Installing Cable Hea d CAUTION Check the location of pin 1 before inserting. Alig n pin 1 on the IC socket f or an FP-112B pack age on th e user s yst em w it h pin 1 on the us er system interf ace board, and insert the u ser system interf ace board into the IC sock et on the us er system , as shown in figure 6. 5.1.3 Fas tening Cable Head [...]

9 Screws (M2.0 x 12 mm) with flat washers Pin 1 Board IC socket (IC 149-112C15333-0B manufactured by YAMAICHI ELECTRONICS Co., Ltd.) User system Figure 6 Connecting User System Interface Board to User System[...]

10 5.2 Connecting User System Interface Board to EV-Chip Board W ARNING Observe the precautions listed below. Failure t o do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user syst em and the emulator product before [...]

11 Connector No. UCN1 UCN1 UCN2 UCN2 Board EV-Chip Board Connector No. Board Connector No. EV-chip board Spacer User system Figure 7 Connecting User System Interface Board to EV-Chip Board[...]

12 5.3 Reco mm ended Dim ensions for U ser System Mount P ad (F ootprint) Figure 8 show s the recom m ended dim ensions f or the m ount pad (footprin t) for the user sy stem w ith an IC socket f or an FP-112B pack age (IC149- 112C15333-0B: m an ufactu red by YA MAIC HI ELECTRONICS C o., Ltd.). Note that the dim ension s in fi gure 8 are som ewh at [...]

13 5.4 Dim ensions for EV-C hip Board and User Syst em Int erface Boar d The dimens ions for the EV- chip board and th e user sy stem in terface board are show n in f igure 9. 140.0 116.0 Unit: mm Tolerance: ±0.5 mm EV-chip board User system interface board 19.5 31.0 33.5 16.0 100.0 92.0 69.0 29.5 5.0 34.5 Spacer Figure 9 Dim ensions for EV-Chip B[...]

14 5.5 Resulting Di mensions after Conn ecting User System Interface B oard The resulting dim ensions, af ter connecting the user sy stem in terface board to the us er system , are shown in figure 10 . 36.0 14.0 61.0 IC socket (IC 149-112C15333-0B manufactured by YAMAICHI ELECTRONICS Co., Ltd.) EV-chip board 12.3 Unit: mm Tolerance: ±1.0 mm User s[...]

15 Section 6 Installing the MCU to the User System CAUTION 1. Check the locat ion of pin 1 before inserting. 2. Use a Philips-type screwdriver whose head matches the screw head. 3. The tightening torque must be 0.098 N•m or less. If the applied torque cannot be accurately measured, stop tightening when th e force required to tu rn the screw becom[...]

16 MCU (SH7144) Screws (M2.0 x 8 mm) with flat washers Socket cover Pin 1 User system IC socket (IC 149-112C15333-0B manufactured by YAMAICHI ELECTRONICS Co., Ltd.) Figure 11 Installing M CU to User System[...]

17 Section 7 Verifying Operation 1. Turn on the em ul ator according to the procedu res described in th e SH7046 E6000H Em ulator User's Manual (HS 7046EPH60HE). 2. Verify th e user sy stem in terface cable connections by check ing the pin states with the extended monitor an d checkin g the bus states w ith th e FILL com m and (emu lator comm [...]

18  To use the crystal oscillator mounted on the EV-chip board Install a crystal oscillator into the crys tal oscillator terminals on the EV-chip board. Evaluation chip board Crystal oscillator terminals Crystal oscillator Enlarged view X1 X2 Figure 13 Installing the Clo ck Oscillator[...]

19 Section 8 Notice 1. Before connectin g any parts or cables, mak e sure that pin 1 on the both sides are correctly aligned. 2. Do not apply excessive force to th e user sy stem interf ace board w hile it is connected to th e user system . 3. The dimen sions of th e recomm ended m ount pad f or the IC socket f or this user sy stem interface board [...]

SH7144 Group FP-112B User System Interface Board HS7144ECH61H User's Manual Publication Date: Rev.4.00, January 29, 2004 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Technical Documentation & Information Department Renesas Kodaira Semiconductor Co., Ltd.  2004 Renesas Technology Corp. All rights reserv[...]

SH7144 Group F P-112B User Sy stem Inte rfac e Board HS7144E C H61H U ser’ s Manual REJ10B0038-0400H[...]