Renesas PLQP0176KB-A инструкция обслуживания

Revision Date: Jan. 09, 2008 Renesas Microcomputer Deve lopment Environment System SuperH ™ Family / SH7280 Series Rev.1.00 SH7286 Group PLQP017 6KB-A User System Interface Boa rd R0E572860CFK00 User’s Manual REJ10J1776-0100[...]

[...]

1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any[...]

[...]

I IMPORTANT INFORMATION READ FIRST • READ this user's manual befo re using this emulato r product. • KEEP the user's manual handy for future reference. Do not at tempt to use t he emulator product unt il you fully underst and its mechanism. Emulator Pr oduct: Throughout this document , the term "emulator product " shall be d[...]

II Target User of the Emulator P roduct: This emulat or product should onl y be used by those w ho have carefully read and thoroughly understood the informat ion and restri ctions cont aine d in the user' s manual. Do not att empt to use the emulator product until you fu lly understand its mechanism. It is highl y recommended that first -time [...]

III LIMITED WARRANTY Renesas warrants its emulator products to be manufactured in accordance with published specifica tions and free from defects in material and/or workmanship. Rene sas, at its option, will replace any emulator products returned intact to the factory, transportation charges prepaid, which Renesas, upon inspection, shall determine [...]

IV State Law : Some states do n ot allow the exclu sion or limitatio n of implied warranties or liability for incidental or consequent ial damages, s o the a bove limitat ion or exclus ion may not apply to you. This warranty gi ves you specifi c legal rights , a nd you may have other right s which may vary from state to state. The Warranty is Vo id[...]

V SAFETY PAGE READ FIRST • READ this user's manual befo re using this emulato r product. • KEEP the user's manual handy for future reference. Do not at tempt to use t he emulator product unt il you fully underst and its mechanism. DEFINITI ON OF SIGNAL WORDS Either in the user's manual or on the produc t, several icons are used t[...]

VI means WARNING or CAUTIO N. Example: CAUTION AG AINST AN ELECT RIC SHOCK means PROHIBITIO N. Example: DISASSEMBLY PROHIBIT ED means A FORCIBLE ACTI ON. Example: UNPLUG T HE POWER CABLE FR OM THE RECEPT ACLE.[...]

VII W ARNING Warnings for AC Power Supply: • If the att ached AC power cable does not fit the receptacle, do not alter the AC power cable and do not plug it forcibly. Failure to comply may cause electric shock and/or fire. • Use an AC power cable which complies with the safety standard of the country. • Do not touch the plug of the AC power c[...]

VIII W ARNING • If you smell a strange odor, hear an unusual sound, or see smoke coming from this product, then disconnect power immediately by unplugging the AC power cable from the outlet. D o not use this as it is because of the danger of elect ric shock and/or fire. In this case, contact your local distributor. • When installing or connecti[...]

IX CA UTION Cautions for AC Adapter: • Use only the AC adapter included in this product package. • The included AC adapter is for this emulator. Do not use it for other product. • The DC plug on the included AC adapter has the below polarity. • The included AC adapter has no power supply switch. The AC adapter is always act ive while connec[...]

X W ARNING Observe the precautions listed below. Failure t o do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Do not repair or rem odel the emulator product by yourself for electric shock prevent ion and quality assurance. 2. Always switc[...]

i Preface The R0E572860CFK00 is a user system interface boa rd that connects a user syst em for the SH7286 PLQP 0176KB-A (former package: F P-176EV) package to the SH7280 E200F emulator (R0E0200F1EMU00 or R0E572800VKK00).[...]

ii Contents Section 1 Configuration ..................................................................................... 1 Section 2 Environmental Conditions ................................................................. 3 Section 3 Connection Procedures ...................................................................... 4 3.1 Connecting Use[...]

1 Section 1 Configuration Figure 1 and table 1 s how the external appearance and components, respecti vely, of the user system interface board for the PLQP0176KB -A. Please make sure you have all of these components when unpacking. Board Screws (M2.0 x 10 mm) Spacer IC socket User system Screws (M2.0 x 6 mm) Socket cover EV-chip unit Figure 1 User [...]

2 CA UTION Use a NQPACK176SD socket (manufactured by Tokyo Eletech Corporation) and a HQPACK176SD ( manufactured by Tokyo Eletech Corporation) for th e PLQP0176KB-A package IC socket and socket cover, resp ect ively, on the user system. Table 1 R0E572860CFK00 Com ponents No. Component Quantity Remarks 1 Board 1 With four spacers (2.6MP x 11 mm ) 2 [...]

3 Section 2 Environmental Conditions Maintain the condit ions in tabl e 2 when using the emulator. Table 2 Environmenta l Conditions Item Specifications Temperature Operating: +10 to +35°C Storage: -10 to +35°C Humidity Operating: 35 to 80% RH, no condensation Storage: 35 to 80% RH, no condensation Vibration Operating: 2.45 m/s 2 max. Storage: 4.[...]

4 Section 3 Connection Procedures 3.1 Connecting User System Int erface Board to User System W ARNING Always switch OFF the user syst em and the emulator product before the USER SYSTEM INTERFACE BOARD is connect ed to or removed from any part. Before connect ing, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result[...]

5 3.1.2 Installing Ca ble Head CA UTION Check the location of pin 1 before inserting. Align pin 1 on the IC socket for a PLQP0176KB-A package on t he user system with pin 1 on t he user system interface board, and ins ert the user system interface board into the IC socket on the user syst em, as shown i n figure 2. 3.1.3 Fastening C able Head CA UT[...]

6 Fasten the user s ystem interf ace board to the IC socket for a PLQP0176KB-A package on the user system wit h the four screws (M2.0 x 10 mm) provided. Each screw should be tightened a little at a time, alternat ing between screw s on opposing corners . Take special care, such as manually securing the IC socket s oldered area, to prevent the solde[...]

7 3.2 Connecting User System Interf ace Board to EV-Chip Board W ARNING Observe the precautions listed below. Failure t o do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF t he user system and the emulator product before [...]

8 Board Spacer User system EV-chip unit Connector No. User I/F Connector 1 (CN4) EV-Chip Unit Connector No. Board Connector No. UCN1 UCN2 User I/F Connector 2 (CN5) Figure 3 Connecting User System Interface Board to EV-Chip Board[...]

9 3.3 Recommended Dimensions for Us er System Mount Pad (Footprint) Figure 4 shows the recommended dimensions for the mount pad (footpri nt) for the user s ystem with an IC s o cket for a PLQP0176K B-A package (NQP ACK176SD: manufactured by Tokyo Eletech Corporati on). Note that the dimens ions in figure 4 are somewhat different from t hose of the [...]

10 3.4 Dimensions for External Bus Tr ace Unit, Emulation Memory Unit, EV-Chip Unit, and User S ystem Interface Board The dimensions for the external bus trace unit, em ulation memory unit, EV-c hip unit, and the user system interface board are shown in figure 5.[...]

11 125.0 90.0 90.0 45.0 5.0 125.0 90.0 110.0 20.0 30.0 60.0 5.0 125.0 90.0 Unit: mm T olerance: ±0.5 mm External bus trace unit Board Spacer EV -chip unit Pin 1 Emulation memory unit Figure 5 Dimensions for External Bus Tra ce Unit, Emulation Memory Unit , EV-Chip Unit, and User System Interface Board[...]

12 3.5 Resulting Dimensions after Conn ecting User System Interface Board The resulting dimensions, after conn ecting the us er system interface board to the user system, are shown in figures 6, 7, and 8. 24.5 55.0 12.5 68.4 30.0 37.5 27.5 29.2 24.5 39.19 39.19 24.5 IC socket (NQPACK176SD manufactured by Tokyo Eletech Corporation) User system Space[...]

13 24.5 42.1 12.5 55.5 30.0 37.5 27.5 29.2 IC socket (NQPACK176SD manufactured by Tokyo Eletech Corporation) User system Pin 1 Top view Spacer ( φ 6.0) Unit: mm Tolerance: ±1.0 mm 24.5 39.19 39.19 24.5 External bus trace unit EV-chip unit Figure 7 Resu lting Dimensi ons after Co nnecting User System Interface B oard (when Connecting External Bus [...]

14 24.5 29.2 12.5 42.6 30.0 37.5 27.5 EV-chip unit Spacer ( φ 6.0) IC socket (NQPACK176SD manufactured by Tokyo Eletech Corporation) User system Unit: mm Tolerance: ±1.0 mm 24.5 39.19 39.19 24.5 Pin 1 Top view Figure 8 Resu lting Dimensi ons after Co nnecting User System Interface B oard (when Connecting EV-Chip Unit )[...]

15 Section 4 Installing the MCU to the User System CA UTION 1. Check t he location of pin 1 befo re inserting. 2. Use a Philips-type screwdr iver whose head matches the screw head. 3. The tightening t orque must be 0.054 N•m or less. If the applied torque ca nnot be accurately measured, stop tightening when th e force required to t urn the screw [...]

16 MCU (SH7286) Screws (M2.0 x 6 mm) Socket cover Pin 1 User system IC socket (NQPACK176SD manufactured by Tokyo Eletech Corporation) Figure 9 Installing MCU to User System[...]

17 Section 5 Verifying Operation 1. Turn on the emulator according to the pro cedures described in the S H-2A, SH-2 E200F Emulator User' s Manual (R0E0200F 1EMU00E or R0E572800EMU00E). 2. The emulator connected to this user syst em interface board supports three kinds of clock sources as t he MCU clock. For deta ils, refer to the S H7080 E200F[...]

18 Section 6 Notice 1. Before connecting any part s or cables, make sure that pin 1 on the both s ides are correctly aligned. 2. Do not apply excessive force to the us er syst em interface board while it is connected to the user sy stem. 3. The dimensions of the recommended mount pad for the IC socket for this us er system interface board are diffe[...]

SH7286 Group PLQP0176KB-A User System Interface Board User's Manual Publication Date: Rev.1.00, January 9, 2008 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Customer Support Department Global Strategic Communication Div. Renesas Solutions Corp. © 2008. Renesas Technology Corp., All rights reserved. Printed i[...]

Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan http://www.renesas.com Refer to " http://www.renesas.com/en/network " for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) [...]

[...]

SH7286 Group PLQP0176KB-A User System Interface Board User’s Manual[...]