Renesas R0E572860CFL00 инструкция обслуживания

Revision Date: Jan. 09, 2008 Renesas Microcomputer Deve lopment Environment System SuperH ™ Family / SH7280 Series Rev.1.00 SH7286 Group PLQP017 6LB-A User System Interface Boa rd R0E572860CFL00 User’s Manual REJ10J1777-0100[...]

[...]

1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any[...]

[...]

I IMPORTANT INFORMATION READ FIRST • READ this user's manual befo re using this emulato r product. • KEEP the user's manual handy for future reference. Do not at tempt to use t he emulator pro duct until you fully understand its mechanism. Emulator Pr oduct: Throughout this document , the term "emulat or product" shall be de[...]

II Target User of the Emulator Pr oduct: This emulator product should only be us ed by those who have careful ly read and thoroughly understood the informat ion and restri ctions cont aine d in the user' s manual. Do not att empt to use the emulator product until you fu lly understand its mechanism. It is highl y recommended that first -time u[...]

III LIMITED WARRANTY Renesas warrants its emulator products to be manufactured in accordance with published specifica tions and free from defects in material and/or workmanship. Rene sas, at its option, will replace any emulator products returned intact to the factory, transportation charges prepaid, which Renesas, upon inspecti on, shall determine[...]

IV State Law : Some states do n ot allow the exclu sion or limitatio n of implied warranties or liability for incidental or consequent ial damages, s o the a bove limitat ion or exclusi on may not apply to you. This warranty gi ves you specifi c legal right s, a nd you may have other right s which may vary from state to state. The Warranty is Vo id[...]

V SAFETY PAGE READ FIRST • READ this user's manual befo re using this emulato r product. • KEEP the user's manual handy for future reference. Do not at tempt to use t he emulator pro duct until you fully understand its mechanism. DEFINITI ON OF SIGNAL WORDS Either in the user's manual or on the produc t, several icons are used to[...]

VI means WARNING or CAUTIO N. Example: CAUTION AG AINST AN ELECT RIC SHOCK means PROHIBITIO N. Example: DISASSEMBLY PROHIBIT ED means A FORCIBLE ACT ION. Example: UNPLUG T HE POWER CABLE F ROM THE R ECEPTACLE.[...]

VII W ARNING Warnings for AC Power Supply: • If the att ached AC power cable does not fit the receptacle, do not alter the AC power cable and do not plug it forcibly. Failure to comply may cause electric shock and/or fire. • Use an AC power cable which complies with the safety standard of the country. • Do not touch the plug of the AC power c[...]

VIII W ARNING • If you smell a strange odor, hear an unusual sound, or see smoke coming from this product, then disconnect power immediately by unplugging the AC power cable from the outlet. D o not use this as it is because of the danger of elect ric shock and/or fire. In this case, contact your local distributor. • When installing or connecti[...]

IX CA UTION Cautions for AC Adapte r: • Use only the AC adapter included in this product package. • The included AC adapter is for this emulator. Do not use it for other product. • The DC plug on the included AC adapter has the below polarity. • The included AC adapter has no power supply switch. The AC adapter is always act ive while conne[...]

X W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Do not repair or rem odel the emulator product by yourself for electric shock prevent ion and quality assurance. 2. Always switch[...]

i Preface The R0E572860CFL00 is a user system interface boa rd that connects a user system for the SH7286 PLQP 0176LB-A (former package: FP -176AV) package to the SH7280 E200F emulator (R0E0200F1EMU00 or R0E572800VKK00).[...]

ii Contents Section 1 Configuration ..................................................................................... 1 Section 2 Environmental Conditions ................................................................. 3 Section 3 Connection Procedures ...................................................................... 4 3.1 Connecting Use[...]

1 Section 1 Configuration Figure 1 and table 1 s how the external appearance and components, respectivel y, of the user system interface board for the PLQP0176LB -A. Please make sure you have all of these components when unpacking. Board Screws (M2.0 x 10 mm) Spacer IC socket User system Screws (M2.0 x 6 mm) Socket cover EV-chip unit Figure 1 User [...]

2 CA UTION Use a NQPACK 176SE socket (manufact ured by Tokyo Eletech Corporation) and a HQPACK176SE (manuf actured by Tokyo Eletech Corporation) for the PLQP0176LB -A package IC socket and socket cover, resp ect ively, on the user system. Table 1 R0E572860CFL 00 Componen ts No. Component Quantity Remarks 1 Board 1 With four spacers (2.6MP x 11 mm )[...]

3 Section 2 Environmental Conditions Maintain the condit ions in tabl e 2 when using the emulator. Table 2 Environmenta l Conditions Item Specifications Temperature Operating: +10 to +35°C Storage: -10 to +35°C Humidity Operating: 35 to 80% RH, no condensation Storage: 35 to 80% RH, no condensation Vibration Operating: 2.45 m/s 2 max. Storage: 4.[...]

4 Section 3 Connection Procedures 3.1 Connecting User System Int erface Board to User System W ARNING Always switch OFF the user syst em and the emulator product before the USER SYSTEM INTERFACE BOARD is connect ed to or removed from any part. Before connect ing, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result[...]

5 3.1.2 Installing Ca ble Head CA UTION Check the location of pin 1 before inserting. Align pin 1 on the IC socket for a PLQP0176LB-A package on the us er system with pin 1 on the user system interface board, and ins ert the user system interface board into the IC socket on the user syst em, as shown in fi gure 2. 3.1.3 Fastenin g Cable Head CA UTI[...]

6 Fasten the user s y stem interf ace board to the IC s o cket for a PLQP0176LB-A package on the user system wi th the four screws (M2.0 x 10 mm) provided. Each s crew should be tightened a little at a time, alternati ng between screws on opposing corners. Take s p ecial care, such as manual ly securing the IC socket soldered area, to prevent the s[...]

7 3.2 Connecting User System Interf ace Board to EV-Chip Board W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF t he user system and the emulator product before t[...]

8 Board Spacer User system EV-chip unit Connector No. User I/F Connector 1 (CN4) EV-Chip Unit Connector No. Board Connector No. UCN1 UCN2 User I/F Connector 2 (CN5) Figure 3 Connecting User System Interface Board to EV-Chip Board[...]

9 3.3 Recommended Dimensions for Us er System Mount Pad (Footprint) Figure 4 shows the recommended dimensions for the mount pad (footpri n t) for the user s y stem with an IC s o cket for a PLQP0176LB -A package (NQPACK176SE: manufact ured by Tokyo Eletech Corporati on). Note that the dimens ions in figure 4 are somewhat different from thos e of th[...]

10 Up to 1.2 1.3 to 2.0 2.1 to 5.0 5.1 to 10 10.1 or above 7 0.4 0.2 7 Pin 1 2 2 19.1 23.1 3-Ø1.0 Ø2.2 (SL-type) 0.4 × 43 = 17.2 Dimension and tolerance Dimension T olerance ± ± ± ± 0.20 0.05 0.10 ± 0.15 0.30 Unit: m m Figure 4 Recommended Dimensions f or Mount Pa d[...]

11 3.4 Dimensions for External Bus Tr ace Unit, Emulation Memory Unit, EV-Chip Unit, and User S ystem Interface Board The dimensions for the external bus trace unit, em ulation memory unit, EV-c hip unit, and the us er system interface board are shown in figure 5.[...]

12 125.0 90.0 90.0 45.0 5.0 125.0 90.0 110.0 20.0 30.0 60.0 5.0 125.0 90.0 Unit: mm T olerance: ±0.5 mm External bus trace unit Board Spacer EV -chip unit Pin 1 Emulation memory unit Figure 5 Dimensions for External Bus Tra ce Unit, Emula tion Memory Unit , EV-Chip Unit, and User System Interface Board[...]

13 3.5 Resulting Dimensions after Conn ecting User System Interface Board The resulting dimensions, after conn ecting the us er system interface board to the user system, are shown in figures 6, 7, and 8. 24.5 55.0 12.5 68.4 IC socket (NQPACK176SE manufactured by User system Spacer ( φ 6.0) External bus trace unit 30.0 37.5 27.5 29.2 Unit: mm Tole[...]

14 24.5 42.1 12.5 55.5 IC socket (NQPACK176SE manufactured by User system Spacer ( φ 6.0) 30.0 37.5 27.5 29.2 Unit: mm 24.5 39.19 39.19 24.5 Pin 1 Top view External bus trace unit EV-chip unit Tokyo Eletech Corporation) Tolerance: ±1.0 mm Figure 7 Resu lting Dimension s after Co nnecting User System In terface Board (when Connecting External Bus [...]

15 24.5 29.2 12.5 42.6 IC socket (NQPACK176SE manufactured by Tokyo Eletech Corporation) User system Spacer ( φ 6.0) EV-chip unit 30.0 37.5 27.5 Unit: mm Tolerance: ±1.0 mm 24.5 39.19 39.19 24.5 Pin 1 Top view Figure 8 Resu lting Dimension s after Co nnecting User System In terface Board (when Connecting EV-Chip Unit )[...]

16 Section 4 Installing the MCU to the User System CA UTION 1. Check t he location of pin 1 before insert ing. 2. Use a Philips-type screwdr iver whose head matches the screw head. 3. The tightening t orque must be 0.054 N•m or less. If the applied torque ca nnot be accurately measured, stop tightening when the f orce required to turn the screw b[...]

17 User system IC socket (NQPACK176SE manufactured by Tokyo Eletech Corporation) Screws (M2.0 x 6 mm) Socket cover MCU (SH7286) Pin 1 Figure 9 Installing MCU to User System[...]

18 Section 5 Verifying Operation 1. Turn on the emulator according to the pro cedures described in the SH -2A, SH-2 E200F Emulator User' s Manual (R0E0200F 1EMU00E or R0E572800EMU00E). 2. The emulator connected to this user syst em interface board supports three kinds of clock sources as t he MCU clock. For detai ls, refer to the SH7280 E200F [...]

19 Section 6 Notice 1. Before connecting any part s or cables, make sure that pin 1 on the both s ides are correctly aligned. 2. Do not apply excessive force to the us er syst em interface board while it is connected to the user sy stem. 3. The dimensions of the recommended mount pad for the IC socket for this us er system interface board are diffe[...]

20[...]

SH7286 Group PLQP0176LB-A User System Interface Board User's Manual Publication Date: Rev. 1.00, January 9, 2008 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Customer Support Department Global Strategic Communication Div. Renesas Solutions Corp. © 2008. Renesas Technology Corp. All rights reserved. Printed i[...]

Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan http://www.renesas.com Refer to " http://www.renesas.com/en/network " for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) [...]

[...]

SH7286 Group PLQP0176LB- A User System Interface Board User’s Manual[...]