Renesas SH7206 инструкция обслуживания

Revision Date: A ug. 08, 2006 Renesas Microcomputer Deve lopment Environment System SuperH TM Family / SH7200 Ser ies R0E572060CFK00 Rev.1.02 SH7206 Group FP-176 C User System Interface Boa rd User’s Manual REJ10B0179-0102[...]

[...]

1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party. 2. Renesas Technology Corp[...]

[...]

I IMPORTANT INFORMATION READ FIRST • READ this user's manual befo re using this emulato r product. • KEEP the user's manual handy for future reference. Do not at tempt to use the emulator pro duct until yo u fully understand it s mechanism. Emulator Pr oduct: Throughout this document , the term "emulator product " shall be d[...]

II Target User of the Emulator Pr oduct: This emulator product should only be us ed by those who have careful ly read and thoroughly understood the informat ion and restrict ions contai ne d in the user's manual. Do not attempt to use the emulator product until you fu lly understand its mechanism. It is highl y recommended that first -time use[...]

III LIMITED WARRANTY Renesas warrants its emulator products to be manufactured in accordance with published specifica tions and free from defects in material and/or workmanship. Rene sas, at its option, will replace any emulator products returned intact to the factory, transportation charges prepaid, which Renesas, upon inspection, shall determine [...]

IV State Law : Some states do n ot allow the exclu sion or lim itation of im plied warran ties or liability f or incidental or consequent ial damages, s o the a bove limitat ion or exclusion may not apply to you. This warranty gi ves you specifi c legal rights , a nd you may have other rights which may vary from state to state. The Warranty is Vo i[...]

V SAFETY PAGE READ FIRST • READ this user's manual befo re using this emulato r product. • KEEP the user's manual handy for future reference. Do not at tempt to use the emulator pro duct until yo u fully understand it s mechanism. DEFINITI ON OF SIGNAL WORDS Either in the user's manual or on the produc t, several icons are used t[...]

VI means WARNING or CAUTIO N. Example: CAUTION AG AINST AN ELECT RIC SHOC K means PROHIBITIO N. Example: DISASSEMBLY PROHIBIT ED means A FORCIBLE ACT ION. Example: UNPLUG T HE POWER CABLE F ROM TH E RECEPTACLE.[...]

VII W ARNING Warnings for AC Power Supply: • If the att ached AC power cable does not fit the receptacle, do not alter the AC power cable and do not plug it forcibly. Failure to comply may cause electric shock and/or fire. • Use an AC power cable which complies with the safety standard of the country. • Do not touch the plug of the AC power c[...]

VIII W ARNING • If you smell a strange odor, hear an unusual sound, or see smoke coming from this product, then disconnect power immediately by unplugging the AC power cable from the outlet. D o not use this as it is because of the danger of elect ric shock and/or fire. In this case, contact your local distributor. • When installing or connecti[...]

IX CA UTION Cautions for AC Adapte r: • Use only the AC adapter included in this product package. • The included AC adapter is for this emulator. Do not use it for other product. • The DC plug on the included AC adapter has the below polarity. • The included AC adapter has no power supply switch. The AC adapter is always act ive while conne[...]

X W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Do not repair or rem odel the emulator product by yourself for electric shock prevent ion and quality assurance. 2. Always switch[...]

i Preface The R0E572060CFK00 is a user system interface boa rd that connects a user syst em for the SH7206 FP-176C package to the SH7206 E200F emulator (R 0E0200F1EMU00 or R0E572060VKK00).[...]

ii Contents Section 1 Configuration ..................................................................................... 1 Section 2 Environmental Conditions ................................................................. 3 Section 3 Connection Procedures ...................................................................... 4 3.1 Connecting Use[...]

1 Section 1 Configuration Figure 1 and table 1 show the conf iguration and component s of the user system interface board for the FP-176C package. P lease make sure you have all of these components w hen unpacking. Board Screws (M2.0 x 10 mm) Spacer IC socket User system EV-chip unit External bus trace unit Screws (M2.0 x 6 mm) Socket cover Figure [...]

2 CA UTION Use a NQPACK 176SD socket (manuf actured by Tokyo Eletech Corporation) for the FP- 176C package IC socket on the user system. Table 1 R0E572060CFK00 Com ponents No. Component Quantity Remarks 1 Board 1 With four spacers (2.6MP x 11 mm ) 2 IC socket 1 For the FP-176C package (to be mounted on the user system) 3 Socket cover 1 For the FP-1[...]

3 Section 2 Environmental Conditions Maintain the condit ions in tabl e 2 when using the emulat or. Table 2 Environmenta l Conditions Item Specifications Temperature Operating: +10 to +35°C Storage: -10 to +35°C Humidity Operating: 35 to 80% RH, no condensation Storage: 35 to 80% RH, no condensation Vibration Operating: 2.45 m/s 2 max. Storage: 4[...]

4 Section 3 Connection Procedures 3.1 Connecting User System Int erface Board to User System W ARNING Always switch OFF the user syst em and the emulator product before the USER SYSTEM INTERFACE BOARD is connect ed to or removed from any part. Before connect ing, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result[...]

5 3.1.2 Installing Ca ble Head CA UTION Check the location of pin 1 before inserting. Align pin 1 on t he IC socket for an FP -176C package on the user system wi th pin 1 on the user system interface board, and insert the us er system interface board into the IC socket on the user system, as shown in figure 2. 3.1.3 Fastenin g Cable Head CA UTION 1[...]

6 Board Screws (M2.0 x 10 mm) User system IC socket (NQPACK176SD manufactured by Tokyo Eletech Corporation) Pin 1 Figure 2 Connecting User System In terface Board to User System[...]

7 3.2 Connecting User System Interf ace Board to EV-Chip Unit W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF t he user system and the emulator product before th[...]

8 Board Spacer User system EV-chip unit Connector No. User I/F Connector 1 (CN3) EV-Chip Unit Connector No. Board Connector No. UCN1 UCN2 User I/F Connector 2 (CN4) External bus trace unit Pin 1 Figure 3 Connecting User System In terface Board to EV-Chip Unit[...]

9 3.3 Recommended Dimensions for Us er System Mount Pad (Footprint) Figure 4 shows the recommended dimensions for the mount pad (footpri n t) for the user s ystem with an IC s ocket for an FP-176C package (N QPACK176S D: manufactured by Tokyo Eletech Corporation). Note t h at the dimensions in figure 4 are somewhat different from those of t he actu[...]

10 Unit: mm Pin 1 10.0 φ 1.0 10.0 0.25 2.00 0.50 × 43 = 21.50 0.50 × 43 = 21.5 23.10 max 27.10 min 0.5 0.50 Location determination hole Dimension and tolerance Tolerance ±0.05 ±0.10 ±0.15 ±0.20 ±0.30 Dimension Up to 1.2 1.3 to 2.0 2.1 to 5.0 5.1 to 10.0 10.1 or above Figure 4 Recommended Dimensio ns for Mount P ad[...]

11 3.4 Dimensions for External Bus Tr ace Unit, EV-Chip Unit, and User System Interface Board The dimensions for the external bus trace unit, EV -chip unit, and the user system interface board are shown in figure 5. 125.0 90.0 90.0 45.0 5.0 Unit: mm External bus trace unit Board Spacer 125.0 90.0 EV-chip unit 110.0 20.0 30.0 60.0 5.0 Pin 1 Dimensio[...]

12 3.5 Resulting Dimensions after Conn ecting User System Interface Board The resulting dimensions, after conn ecting the us er system interface board to the user system, are shown in figures 6, 7, and 8. 24.5 55.0 12.5 68.4 30.0 37.5 27.5 29.2 IC socket (NQPACK176SD manufactured by Tokyo Eletech Corporation) User system Spacer ( φ 6.0) EV-chip un[...]

13 24.5 42.1 12.5 55.5 30.0 37.5 27.5 29.2 IC socket (NQPACK176SD manufactured by Tokyo Eletech Corporation) User system Spacer ( φ 6.0) 39.19 24.5 24.5 39.19 EV-chip unit External bus trace unit Pin 1 Unit: mm Dimension and tolerance Tolerance ±0.05 ±0.10 ±0.15 ±0.20 ±0.30 Dimension Up to 1.2 1.3 to 2.0 2.1 to 5.0 5.1 to 10.0 10.1 or above F[...]

14 24.5 29.2 12.5 42.6 30.0 37.5 27.5 EV-chip unit Spacer ( φ 6.0) IC socket (NQPACK176SD manufactured by Tokyo Eletech Corporation) User system 39.19 24.5 24.5 39.19 Pin 1 Unit: mm Dimension and tolerance Tolerance ±0.05 ±0.10 ±0.15 ±0.20 ±0.30 Dimension Up to 1.2 1.3 to 2.0 2.1 to 5.0 5.1 to 10.0 10.1 or above Figure 8 Resu lting Dimension [...]

15 Section 4 Installing the MPU to the User System CA UTION 1. Check t he location of pin 1 before insert ing. 2. Use a Philips-type screwdr iver whose head matches the screw head. 3. The tightening t orque must be 0.054 N•m or less. If the applied torque ca nnot be accurately measured, stop tightening when the f orce required to turn the screw b[...]

16 MPU (SH7206) Screws (M2.0 x 6 mm) Socket cover Pin 1 User system IC socket (NQPACK176SD manufactured by Tokyo Eletech Corporation) Figure 9 Installing MPU to User System[...]

17 Section 5 Verifying Operation 1. Turn on the emulator according to the pro cedures described in th e SH7206 E200F Emulator User's Manual (R0E0200F 1EMU00E or R0E572060VKK00E). 2. Verify the user system interface cable c onnections by checking the pin states with the extended monitor and checking t he bus states with the FILL command (emulat[...]

18 Section 6 Notice 1. Before connecting any part s or cables, make sure that pin 1 on the both s ides are correctly aligned. 2. Do not apply excessive force to the us er syst em interface board while it is connected to the user sy stem. 3. The dimensions of the recommended mount pad for the IC socket for this us er system interface board are diffe[...]

SH7206 Group FP-176C User System Interface Board User's Manual Publication Date: Rev.1.00, September 14, 2004 Rev.1.02, August 8, 2006 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Customer Support Department Global Strategic Communication Div. Renesas Solutions Corp. © 2006. Renesas Technology Corp. All righ[...]

Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan http://www.renesas.com Refer to " http://www.renesas.com/en/network " for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) [...]

[...]

SH7206 Group FP-176C User System Interface Board User’s Manual[...]