Renesas TFP-100G инструкция обслуживания

H8/3854 Series TFP-100G User System Interface Cable (HS3854ECN61H) for E6000 Emulator User’s Manual HS3854ECN61HE(B)[...]

[...]

Cautions 1. Renesas neither warrants nor grants li censes of any rights of Renesas’s or any t hird party’s patent, copyright, t rademark, or other intel lect ual property rights for informat ion contained in this document. Renesas bears no responsibility fo r problem s that may arise with third party’s rights, including int ellectual property[...]

[...]

i Preface Thank you for purchasing this user system interface cable (HS3854ECN61H) for the Renesas’s original mi crocomputer H8/3854 series. The HS3854ECN61H is a user system interface cab le that connects an H8/300L series E6000 emulator (HS3L08EPI60H; hereinafter referred to as the em ulator) through the expansion board to the IC socket for a T[...]

ii Contents Section 1 Configuration .................................................................................... 1 Section 2 Connection Procedures ...................................................................... 3 2.1 Connecting User System Interf ace Cable to Expansion Board ......................................... 3 2.2 Connecting [...]

Section 1 Configuration CAUTION Use an NQPACK100SE socket (manufactured by Tokyo Eletech Corporation) for the TFP-100G package IC socket on the user system. Figure 1 shows the configuration of the HS3854E CN61H user system interface cable for the TFP-100G package. Figure 1 HS3854ECN61H User System Interface Cable 1[...]

2 Table 1 lists t he HS3854ECN61H components. Please m ake sure you have all of these com ponents when unpacking. Table 1 HS3854ECN61H Components No. Component Quantity Remarks 1 Cable body 1 Flat cable 2 Cable head 1 3 IC socket 1 For the TFP-100G package 4 Socket cover 1 For installing an TFP-100G packaged MCU 5 Screws (M2.0 x 10 mm) 4 For fasten[...]

Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Expansion Board W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and w ill damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user system an[...]

2. [1] After maki ng sure the direction of the expansi on board connector labeled E6000 EMULATOR is correct, firm ly insert the expansion board connect or into the emulat or station connector ([1] i n figure 2). [2] Connect the expansion board labeled USER INTERFACE CABLE and the user system interface cable body. 6 0 0 0 USE RI N T ERF A C E C ABLE[...]

2.2 Connecting User System Interface Cable to User System W ARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pi n 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the[...]

6 2.2.3 Inserting Cable Head CAUTION Check the location of pin 1 before inserting. Align pin 1 on the IC socket for an TFP-100G package on t he user system wit h pin 1 on the user system interface cable head, and inse rt the user system interface cable head into the IC socket on the user system, as shown i n figure 3. 2.2.4 Fastening Cable Head CAU[...]

Fasten the user system interface cable head to the IC socket fo r an TFP-100G package on the user system wit h the four screws (M2.0 x 10 m m) provided. Each screw should be tightened a little at a time, alternating between screws on opposi ng corners. Take special care, such as manually securing the IC socket soldered area, to prevent the soldered[...]

2.2.5 Fastening Cable Body Connect the cable body to the cable head. Cable body Cable head Remove jig Push the remove jig Removing User system Figure 4 Fastening Cable Body 8[...]

2.3 Recommended Dimensions for User System Mount Pad Figure 5 shows t he recomm ended dim ensions for the mount pad (footprint) for the user system with an IC socket for an TFP-100G package (NQPACK100SE: m anufactured by Tokyo Eletech Corporation). Not e that the dimensions in figure 5 are somewhat different from those of t he actual chip's m [...]

2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interf ace cable head are shown in figure 6. Figure 6 Dimensions for User System Interface Cable Head 10[...]

2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after conn ecting the user system interface cab le head to the user system, are shown in figure 7. Figure 7 Resulting Dimensions after Connecting User System Interface Cable 11[...]

12 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a screwdriver w hose head matches the screw head. 3. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantl[...]

Figure 8 Installing MCU to User System 13[...]

14 Section 4 Verifying Operation 1. When using the H8/300L series E6000 emulat or (HS3L08EPI60H), turn on the emulat or according to the procedures described in th e H8/300 Series E6000 Emulator User's Manual (HS3008EPI60HE). 2. Verify the user system interface cable c onnections by accessing ports and checking the bus states of the pins. If a[...]

Figure 9 shows the system clock oscillator on the us er system interface cable and the subclock input specifications. Figure 9 System Clock Oscillator and Subclock Input Specifications 15[...]

Section 5 Notice 1. Make sure that pin 1 on the user syst em IC socket is correct ly aligned with pin 1 on t he cable head before inserting the cable head into the user system IC socket. 2. The dimensions of t he recommended m ount pad for the user system IC socket are different from those of the MCU. 3. To avoid breaking wires in the cable body, d[...]