RIDGID AC9940 инструкция обслуживания

1 This Miter Saw Utility V ehicle has been engineered and manufactured to our high standar d for dependability , ease of op- eration and operator safety . When properly car ed for , the Miter Saw Utility V ehicle will give you years of rugged, trouble-free performance. WARNING T o reduce the risk of injury , the user must read and understand the op[...]

2 n Introduction ...................................................................................................................................................................... 2 n Rules for Safe Operation .........................................................................................................................................[...]

3 RULES FOR SAFE OPERA TION Safe operation of this accessory requir es that you read and understand this operator's manual, the operator’ s manual for the miter saw and all labels affixed to the tool. READ ALL INSTRUCTIONS n KNOW YOUR ACCESSOR Y . Read the operator's manual carefully . Lear n the product's applications and limitati[...]

4 SYMBOLS The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger . The instructions or war nings they give ar e not substitutes for proper accident pr evention m[...]

5 UNP ACKING NOTE: Before beginning assembly , check that all parts are included. If you ar e missing any part, do not assemble this accessory . Call 1-800-4-RIDGID or E-mail us at info@rid gidwoodworking.com to get the missing part. Sometimes n Stand Assembly (1) n Roller Assembly (2) n Wheels (2) n Operator's Manual (1) n Hex Bolt, M8x50 mm [...]

6 Fig. 3 ASSEMBL Y A TT ACHING THE LOWER FOOT See Figures 1 and 2. n Place stand assembly “flat” on floor . n Rotate lower foot into upright position aligning holes as shown. n Locate the following parts: Hex Bolt, M8 x 50 mm (2) Flat W asher , M8 (4) Lock Nut, M8 (2) n Install bolt, two washers and lock nut as shown. Finger tighten lock nut. n[...]

7 WORKST AND SET -UP See Figures 4 and 5. Before Y ou Start n If a miter saw is already assembled to the stand, make sure that it is securely attached to the stand per the instructions in this manual. n If a compound miter saw is already assembled to the stand, make sure to place the blade 90° to the table (if applicable). Miter the blade to the r[...]

8 ASSEMBL Y MOUNTING MITER SA W See Figures 6 and 7. WARNING: Failure to unplug the tool could r esult in accidental starting causing possible serious personal injury . Before Y ou Start RIDGID miter saws bolt directly onto this workstand. When you ar e finished attaching your saw to the workstand re-r ead the Operation and Rules for Safe Operation[...]

9 ASSEMBL Y MOUNTING OTHER BRANDS See Figure 8. NOTE: Other brands of miter saws (not RIDGID miter saws) will requir e additional 5/16 in. mounting holes to be drilled. See instructions below . n Locate the following parts: Hex Bolts, M6 x 40mm (4) Flat W ashers, M6 (4) Fender W ashers, M6 (4) Lock Nuts, M6 (4) CENTER THE MITER SAW ON THE WORKST AN[...]

10 ASSEMBL Y EXTENSION BAR(S) OPERA TION See Figures 10 and 11. Both extension bars may be adjusted to pr ovide maximum workpiece support. T o adjust the extension bars: n Loosen adjustable handle by tur ning counter clockwise. NOTE: Adjustable handle can be repositioned if necessary . Lift up on handle and rotate to desired position then release h[...]

11 FOLDING LEG AND T ABLE n Loosen the r oller foot knob and slide foot extension up. Tighten knob. n Release locking pin and raise foot. n Loosen the extension bar handle and slide extension bar in towards table. Tighten extension bar handle. n Repeat for the other side. n At the wheel end of the stand firmly grab the lift handle/ lock lever and s[...]

12 ASSEMBL Y TRANSPORTING TOOL See Figure 15. n When hauling the workstand in a vehicle, securely tie it down to prevent movement and possible damage. n Always get help if you need to lift the workstand. When lifting, hold the workstand close to your body . Bend your knees so you can lift with your legs, not your back. MAINTENANCE See Figures 16 an[...]

13 EXPLODED VIEW/REP AIR P AR TS Miter Saw Utility V ehicle Model AC99400 RIDGID parts are at www .ridgidparts.com 1 829859 Rear Roller Extension 2 829758-5 W asher (20 x 10.5 x 1.5) 3 829759-3 Nylock Nut (M10) 4 829799 Rubber Cap 5 829757-6 Hex Head Bolt (M8 x 1.25 x 33) 6 830256 T able 7 829871-1 Compression Spring 8 829741 Clamp 9 829758-5 W ash[...]

14 NOTES[...]

15 W ARRANTY Proof of purchase must be presented when requesting war - ranty service. Limited to RIDGID ® hand held and stationary power tools purchased 2/1/04 and after . This product is manufactured by One W orld T echnologies, Inc. The trademark is licensed from RIDGID, Inc. All warranty communications should be dir ected to One W orld T echnol[...]

16 Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center . Be sure to pr ovide all relevant information when you call or visit. For the location of the authorized service center near est you, please call 1-866-539-1710 or visit us online at www .ridgid.com. The model number and serial number are f[...]