RIDGID R5010 инструкция обслуживания

Your new drill has been engineered and manufactured to our high standards for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this product. Thank yo[...]

2 T ABLE OF CONTENTS      Introduction ............................................................................................................................................................... 2      General Safety Rules .............................................................................................[...]

3 WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SA VE THESE INSTRUCTIONS W ork Area  Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.  Do not operate power tools in explosive atmo- sphe[...]

4 SPECIFIC SAFETY RULES  Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator. Additional Safety Rules      Know your power tool. Read operator ?[...]

5 Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power min Minutes Time Alterna[...]

6 SPECIFICA TIONS Chuck Capacity ................................................................................................................. ........................ 1/2 in. (13 mm) Input ................................................................................................................... 120 Volts, 60 Hz, AC only, 9.0 amperes S[...]

7 UNP ACKING Instructions Your drill has been shipped completely assembled.  Carefully remove the tool from the box.  Make sure that all items listed in the packing list are included.  Inspect the tool carefully to make sure no breakage or damage occurred during shipping.  Do not discard the packing material until you have carefully ins[...]

8 Before using this product, familiarize yourself with all operating features and safety requirements. However, do not let familiarity with the tool make you careless. WARNING: Exercise caution when using this tool. Careless actions, for even a fraction of a second, can result in serious personal injury. Your new tool is equipped with the following[...]

9 OPERA TION WARNING: Always wear safety goggles or safety glasses with side shields when operating this tool. Failure to do so could result in dust, shavings, or loose par- ticles being thrown into your eyes, resulting in possible serious injury. SWITCH See Figure 2. To turn your drill ON , depress the switch trigger. Release switch trigger to tur[...]

10 OPERA TION Fig. 5 TO INCREASE SPEED, PULL SWITCH TRIGGER VARIABLE SPEED See Figures 5 & 8. Your drill has a variable speed dial designed to allow operator control of speed and torque limits. The speed and torque of your drill can be increased by turning the dial on top of the drill. Avoid running your drill at low speeds for extended periods[...]

11 OPERA TION ADJUSTING THE AUXILIARY HANDLE ASSEMBLY See Figure 7. Follow these steps to adjust the auxiliary handle assembly.  Loosen the auxiliary handle assembly by turning the knob counterclockwise.  Rotate the auxiliary handle assembly to the desired location.  Tighten the auxiliary handle assembly securely by turning the knob clockw[...]

12 OPERA TION TO INSTALL BITS See Figures 10 and 11.      Unplug your drill. WARNING: Failure to unplug your drill could result in acciden- tal starting causing serious injury.      Open or close the chuck jaws to a point where the opening is slightly larger than the drill bit you intend to use. Also, raise the front o[...]

13 OPERA TION DRILLING See Figure 12.      Depress and release switch trigger to be sure your drill is in OFF position before connecting it to power supply.      Check the direction of rotation lever for correct setting (forward or reverse). See Figure 4.      Secure the material to be drilled in a vise [...]

14 CHUCK REMOVAL See Figure 13. The chuck must be removed in order to use some accessories. To remove:      Unplug your drill. WARNING: Failure to unplug your drill could result in acciden- tal starting causing serious injury.      Using two open-end wrenches, loosen the chuck. See Figure 13.      This w[...]

15 MAINTENANCE GENERAL Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc. WARNING : Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc. come [...]

W ARRANTY 16 This product is manufactured under license from Ridgid, Inc. by One World Technologies, Inc. All warranty communications should be directed to One World Technologies, Inc. at (toll-free) 1-866-539-1710. 90-DAY SATISFACTION GUARANTEE POLICY During the first 90 days after the date of purchase, if you are dissatisfied with the performance[...]

NOTES 17[...]

Customer Service Information For parts or service, contact your nearest Ridgid authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www.ridgidwoodworking.com. The model number of this tool is foun[...]