RIDGID R86006 инструкция обслуживания

1 Y ou r drill has been engineer ed and manufactur ed to our high standar ds for dependability , ease of operation, and operator safety . When properly car ed for , it will give you years of rugged, trouble-free performance. WARNING: T o reduce the risk of injury , the user must read and understand the operator’ s manual before using this pr oduc[...]

2  Introduction......................................................................................................................................................................2  General Safety Rules .....................................................................................................................................[...]

3 GENERAL SAFETY RULES WARNING! RE AD AND UN DE RS T AN D ALL IN STR UC TI ONS . Failure to follow all instructions listed below , may r esult in elect ric sho ck, fir e and /or ser ious persona l injury . SA VE THESE INSTRUCTIONS WORK AREA  Keep your work area clean and well lit. Clu t te red benches and dark areas invite accidents.  D[...]

4 SERVICE  T ool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel may result in a risk of injury . GENERAL SAFETY RULES  When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized pa[...]

5 SYMBOLS Some of the following symbols may be used on this product. Please study them and lear n their meaning. Proper interpretation of these symbols will allow you to operate the pr oduct better and safer . V V olts V oltage A Amperes Current Hz Hertz Frequency (cycles per second) W W att Power min Minutes Time Alternating Current T ype of curre[...]

6 SYMBOLS SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for repair . When servic- ing, use only identical replacement parts. WARNING: T o avoid serious personal injury , do not attempt to us[...]

7 FEA TURES PRODUCT SPECIFICA TIONS Chuck ...........................................................1/2 in. Keyless Motor .................................................................. 18 V olt DC Switch .......................................................... V ariable Speed No Load Speed ........................ 0-450/0-1,600 r/min (RPM) C[...]

8 FEA TURES KNOW YOUR DRILL See Figure 1. The safe use of this prod uct requ ire s an underst andin g of the information on the product and in this operator’ s manual as wel l as a knowl edge of the pro ject you ar e attem ptin g. Befor e use of this product, familiarize yourself with all operating features and safety rules. BIT STORAGE Bits prov[...]

9 OPERA TION WARNING: Do not allow familiarity with products to make you careless. Remember that a careless fraction of a second is sufficient to inflict sever e injury . WARNING: Always wear safety goggles or safety glasses with sid e shi eld s whe n ope rati ng pr od uct s. Fa ilur e to do so could result in objects being thrown into your eyes re[...]

10 OPERA TION TO INST ALL BA TTER Y P ACK See Figure 2.  Lock the switch trigger on the drill by placing the direction of rotation (forward/reverse/center lock) selector in center position.  Place battery pack in the drill. Align raised rib on battery pack with the groove inside the drill.  Make sure the latches on each side of the battery[...]

11 OPERA TION DIRECTION OF ROT A TION SELECTOR (FORWARD/REVERSE/CENTER LOCK) See Figure 3. The direction of bit rotation is reversible and is controlled by a selector located above the switch trigger . With the drill held in normal operating position, the direction of rotation selector should be positioned to the left of the switch trigger for forw[...]

12 OPERA TION HI SPEED TWO-SPEED GEAR TRAIN (HI-LO) 1 2 LOW SPEED TWO-SPEED GEAR TRAIN See Figure 5. The drill has a two-speed gear train designed for drilling or dri ving at LO (1) or HI (2) speeds . A slid e swit ch is loc ated on top of the drill to select either LO (1) or HI (2) speed. When using drill in the LO (1) speed range, speed will decr[...]

13 OPERA TION CHUCK BODY BIT STORAGE See Figure 8. When not in use, bits provided with the drill can be placed in the storage area located on the base of the drill. INST ALLING BITS See Figure 9.  Lock the swi tch tri gger by placin g the direct ion of rota tion selector in the center position.  Op en or clo se the ch uck ja ws to a po in t w[...]

14 OPERA TION DRILLING See Figure 11.  Check the direction of r otation selector for the correct setting (forward or r everse).  Secure the material to be drilled in a vise or with clamps to keep it from turning as the drill bit rotates.  Hold the drill firmly and place the bit at the point to be drilled.  Depress the switch tr[...]

15 MAINTENANCE WARNING: When servicing use only identical RIDGID ® replacement parts. Use of any other parts may create a hazar d or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty , also wear a dust mask. WARNING: T o avoid seriou[...]

16 MAINTENANCE CHUCK REMOV AL See Figures 12 - 14. The chuck may be removed and r eplaced by a new one.  Lock the swi tch trig ger by placing the dir ect ion of rota tion selector in center position.  Insert a 5/16 in. or larger hex key into the chuck of the drill and tighten the chuck jaws securely .  T ap the hex key sharply wit[...]

17 W ARRANTY Pro of o f pu rch as e m us t be p res en te d wh e n req ue st in g warranty service. Limited to RIDGID ® hand held and stationary power tools purchased 2/1/04 and after . This product is manufactured by One W orld T echnologies, Inc. The trademark is licensed from RIDGID, Inc. All warranty communications should be dir ected to One W[...]

OPERA TOR’S MANUAL 1/2 in. 18 V LITHIUM-ION DRILL TWO-SPEED/REVERSIBLE R86006 Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center . Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or v[...]