Royal Sovereign 1650C инструкция обслуживания

Royal Sovereign LAMINATORS OWNER'S MANUAL RSC-1650H/1650C PLEASE READ AND SAVE INSTRUCTIONS - 1 -[...]

TOPICS PAGE INSTRUCTION -------------------------------------------------------------- - 3 SAFETY PRECAUTIONS ----------------------------------------------------- - 3 CHARACTERISTICS ---------------------------------------------------------- - 4 SPECIFICATIONS -------------------------------------------------------------- - 4 NAMES OF MAJOR PARTS [...]

Thank you for purchasing a Royal Sovereign Roll Laminator. It has been designed and manufactured to provide years of continuous service in the professional environment. To insure high quality lamination, please read this instruction manual thoroughly. This manual will provide you with complete operating and maintenance information. The safet y reco[...]

RS Roll Laminator Line is advanced laminators with time transcendental desi g n, utilizin g the latest in laminatin g technolo gy . It is desi g ned for y ou to set temperature and speed as necessar y . Also y ou can laminate an y thin g at hi g h speed,re g ardless of thickness of material and t y pe of film.It is also desi g ned for convenient us[...]

NO 1 2 3 4 5 6 7 8 9 10 11 12 13 ○ TAKE-UP BOBBIN IDLE BAR HOT ROLLER TABLE-FRONT UPPER ROLLER ○ ○ X TAKE-UP SWITCH ○ ○ PART NAME FRAME-GUIDE,PAPER RSC-1650H RSC-1650H NAMES OF MAJOR PARTS OF MACHINE CONTROL PANEL ○ FOOT SWITCH ○ ASS'Y-STAND PRESSURE LEVER TENSION CONTROL KNOB SAFETY COVER ○ REMOCON SWITCH ○ ○ ○ ○ 6 11 [...]

1. Set the glossy side of upper/lower film to face the heat. ( Glossy side is PET film and matte side is thermal polymer laminating film.) 2. Like picture 1, insert core into the left side of upper/lower film shaft. 3. Like picture 2 and 3, insert core into the right side of upper/lower film. 4. Like picture 4 and 5, adhere core closely. (Make the [...]

1. Set up cold film below the upper bar of the machine. (Set the same as methord of the HOT film for protect paper of lower part) 2. Set the pressure lever to the 15mm, open mode. 3. Insert a piece of wide cardboard (guiding paper/carrier) between the rollers. 4. Pull the film from the upper roller passing over the upper idle bar to the upper rolle[...]

1. For setting, pull the pressure lever out and turn the lever to following the indication 2. OPEN/15mm(Board) : For laminating 15mm thick board (RSC-1650H/1650C) 3. 10~13mm(Board) : For laminating 10~13mm thick board 4. 5~7mm(Board) : For laminating 5~7mm thick board 5. 1mm(Hard Board) : For laminating 1mm thick board 6. Laminating : For laminatin[...]

We designed this machine standing by user’s convenience. You can manipulate speed and temperature . ***Terms*** INSTRUCTIONS FOR CONTROL PANEL 6 1 4 2 6 2 1 3 3 5 - 9 -[...]

1. FUNCTIONS OF CONTROL PANEL RUN/STOP BUTTON : Run or stop the rollers SPEED BUTTON : Increase or decrease speed LED OF SPEED : Display or speed LED OF TEMP. : Display temperature TEMP.BUTTON : Increase or decrease temperature REVERSE BUTTON : To make the rollers run backward 2.HOW TO USE BUTTONS Push the button in order to run rollers and push bu[...]

1. Put cold roll film on upper bar.(Set the same as methord of the HOT film for protect paper of lower part) 2. Pull COLD film, and fix it so that backside protecting paper can be wound on take-up mandrel clockwise. (Revolve core to make protectingpaper tight a little bit.) 3. Set pressure lever at the proper position following to your lamination c[...]

**Cross Cutter** 1. It is on the back side of the machine. 2. After lamination, move cutter to a point about 1/3 of the width of lamination. 3. Grasp film with one hand and press the cutter, cutter downward and slide it to the direction intending to cut with another hand. 4.Press the cutter and slide it the other way. METHOD FOR USING CUTTER - 12 -[...]

1.Please be cautious that neck tie, necklace, long hair, clothes are kept well away while operation. 2.Prevent children from accessing the machine Extreme Heat Will Cause Injury 3.Place the machines on the plated place in order to prevent the machine from damage. 4.Make certain that the machine is connecterd to an ade q uate p ower souce. 5.Do not [...]

CHECK POINT *Rollers do not operate 1. Check the power cord. after press RUN button 2. Check if the switch is on. 3. Check if the emergency switch is off. 4. Check the s/w of safety cover is right. *Wrinkled lamination 1. Adjust film tension. result 6 BOLT CORE 8 Washer( Φ 8) 6 Bolt(M8X12) 1. Power cord may not be plugged in. 2. Power switch is at[...]

1. For six month from the date of purchase, Royal Sovereign International Corporation or its authorized service center will repair this product free of charge if it is defective in material or workmanship. 2. This Limited Warranty does not include cleaning, or damage caused by accident, neglect, misuse or improper installation, operation or externa[...]