Ryobi BE321VS инструкция обслуживания

OPERA TOR’S MANUAL 3 in. BEL T SANDER V ARIABLE SPEED DOUBLE INSULA TED BE321VS SA VE THIS MANUAL FOR FUTURE REFERENCE Y our variable speed belt sander has been engineered and manufactured to Ryobi’ s high standard for dependability , ease of operation, and operator safety . When properly cared for , it will give you years of rugged, tr ouble-f[...]

2 INTRODUCTION This tool has many featur es for making its use mor e pleasant and enjoyable. Safety , performance, and dependability have been given top priority in the design of this product making it easy to maintain and operate. n Introduction .......................................................................................................[...]

3 GENERAL SAFETY RULES n Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the swi tch or pluggi ng in to ols tha t have the swit ch on invites accidents. n Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may re[...]

4 SERVICE n Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel may result in a risk of injury. n When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to fol lo w Ma in [...]

5 SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Pr oper interpreta- tion of these symbols will allow you to operate the tool better and safer . Read The Operator’ s Manual Safety Alert No Hands Symbol No Hands Symbol No Hands Symbol No Hands Symbol SYMBOL NAME DESIGNA TION/EXPLANA TION [...]

6 SYMBOLS SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for r epair . When servic- ing, use only identical replacement parts. WARNING: SA VE THESE INSTRUCTIONS The following signal words and[...]

7 EXTENSION CORDS When using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to handle the current the tool will draw . An undersized cord will cause a drop in line voltage, resulting in overheating and loss of power . Use the chart to determine the minimum wire size requir ed in a[...]

8 FEA TURES Fig. 1 PRODUCT SPECIFICA TIONS Belt Size ..........................................................3 in. x 21 in. Sanding Surface ............................................... 16.5 sq. in. No Load Speed ........................................ 775 - 1,150/min. DUST COLLECTION BAG TRACKING KNOB V ARIABLE SPEED CONTROL DIAL FRONT HANDLE[...]

9 KNOW YOUR BEL T SANDER See Figure 1. Before attempting to use this product, familiarize yourself with all operating features and safety rules. SWITCH TRIGGER T o tur n the sander ON , depress the switch trigger . Release switch trigger to turn your sander OFF . LOCK- ON BUTTON The lock-on feature allows you to lock the switch trigger in the ON po[...]

10 OPERA TION WARNING: Do not allow familiarity with tools to make you care- less. Remember that a careless fraction of a second is sufficient to inflict serious injury . WARNING: Always wear safety goggles or safety glasses with side shields when operating power tools. Failure to do so could result in objects being thr own into your eyes resulting[...]

11 OPERA TION V ARIABLE SPEED See Figure 2. The sander has a variable speed control dial, A (slow) to F (fast) , designed to allow operator control of belt speed. T o increase belt speed, turn the variable speed control dial to a higher setting. T urn to a lower setting to decrease belt speed. Refer to the chart on page 10 for proper speed se- lect[...]

12 OPERA TION TO INST ALL/CHANGE SANDING BEL T See Figures 5 - 6. n Unplug your sander . n Position sander as shown. WARNING: Keep hands and fingers clear of front roller and spring mechanism at all times. Failure to do so could result in them getting pinched, causing possible serious injury . Belt tension must be released in or der to install and [...]

13 OPERA TION LOCKING ON THE SANDER See Figure 7. The lock-on feature allows you to lock the switch trigger in the ON position. Locking the switch trigger on allows you to operate the sander for extended periods of time. If you have the lock-on feature engaged during use and the sander is accidentally disconnected from the power sup- ply , disengag[...]

14 OPERA TION TO ADJUST SANDING BEL T TRACKING See Figure 9. n Connect the sander to power supply . n With sander positioned as shown below , pull switch trig- ger and release immediately . NOTE: This position is for adjustments only . Sanding belt should not be in contact with workpiece or any foreign ob- jects when making belt tracking adjustment[...]

15 OPERA TION WARNING: T o prevent the possibility of sawdust or foreign objects being thrown into your face and eyes, never attempt to use the sander without dust bag pr operly installed. Sawdust or foreign objects being thrown into your face and eyes could result in possible serious injury . DUST BAG See Figure 10. The dust bag pr ovide s a dust [...]

16 MAINTENANCE Ele ct ri c tool s used on fib er gla ss mat er ial , wall boar d, spa ck li ng compounds, or plaster are subject to accelerated wear and possible prematur e failur e because the fiber glass chips and grindings are highly abrasive to bearings, brushes, commu- tator s, etc. Conse quen tly , we do not re comme nded using this tool for [...]

17 TIMING BEL T REPLACEMENT See Figures 11 - 12. n Unplug the sander. WARNING: Failure to unplug the sander could result in accidental starting causing possible serious personal injury . n Remove dust bag. n Remove sanding belt from sander . Follow instructions on page 12 to remove sanding belt. NOTE: Removing sanding belt will simplify the process[...]

18 R YOBI TECHNOLOGIES, INC. 1428 Pearman Dairy Road, Anderson, SC 29625 Post Office Box 1207, Anderson, SC 29622-1207 Phone 1-800-525-2579 www .ryobitools.com 983000-619 11-04 • SER VICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Ryobi Authorized Service Center . Be su[...]