Ryobi RY1201 инструкция обслуживания

7 6 THANK YOU FOR BUYING A R YOBI CORDLESS DRILL-DRIVER. Y our new cordless drill-driver has been engineered and manufactured to Ryobi’s high standard for dependability , ease of operation, and operator safety . Properly cared for , it will give you years of rugged, trouble-free performance. CAUTION: Carefully read through this entire operator ?[...]

Page 2 TABLE OF CONTENTS ■ T able Of Contents/T ypical Applications. ........................................................................................ 2 ■ Rules For Safe Operation .......................................................................................................... 3-5 A. Precautions On Using Y our Cordless T ool ...[...]

Page 3 RULES FOR SAFE OPERA TION The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper ac[...]

Page 4 PRECAUTIONS ON USING YOUR CORDLESS TOOL This product contains Nickel-Cadmium batteries which must be disposed of properly. ■ Be aware that this tool is always in an operating condition, because it does not have to be plugged into an electrical outlet. ■ First, charge the battery. ■ Be sure the battery is snapped in place. ■ When not [...]

Page 5 RULES FOR SAFE OPERA TION (Continued) ■ To reduce risk of damage to electric plug and cord, pull by the plug rather than the cord when disconnecting charger/charging assembly. ■ Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress. ■ An extension cord should not be used u[...]

Page 6 SPECIFICATIONS: RY721 RY961 RY1201 Chuck 3/8 in. Keyless 3/8 in. Keyless 3/8 in. Keyless Motor DC Motor 7.2V DC Motor 9.6V DC Motor 12.0V Switch Two-Speed Variable Speed Variable Speed No Load Speed 330/500 RPM 0 - 550 RPM 0 - 550 RPM Clutch 24 Positions 24 Positions 24 Positions Charger Input 120V, 60 Hz, AC Only 120V, 60 Hz, AC Only 120V, [...]

Page 7 7 6 OPERA TION Fig. 1 Fig. 2 KNOW YOUR DRILL-DRIVER See Figure 1. Before attempting to use any tool, familiarize yourself with all operating features and safety requirements. W ARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. CHARGING YOUR [...]

Page 8 7 6 7 6 OPERA TION Fig. 5 Fig. 4 W ARNING: If any parts are missing, do not operate tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury. SWITCH See Figure 4. Your drill starts and stops by depressing and releasing the switch trigger. Model No. RY721 has a two-speed feature in the switc[...]

Page 9 7 6 7 6 7 6 OPERA TION Fig. 6 Fig. 7 Note: Rotate the chuck body in the direction of the arrow marked GRIP to tighten the chuck jaws. DO NOT use a wrench to tighten or loosen the chuck jaws. W ARNING: Do not insert drill bit into chuck jaws and tighten as shown in figure 8. This could cause drill bit to be thrown from drill resulting in poss[...]

Page 10 6 7 7 6 7 6 OPERA TION REMOVING BITS See Figure 7. ■ Place the direction of rotation selector in center position. This will lock the switch trigger in the off position. ■ Loosen the chuck jaws from drill bit . ■ T o loosen: grasp and hold the collar of the chuck with one hand, while rotating chuck body with your other hand. Note: Rota[...]

Page 11 5 6 7 OPERA TION W ARNING: Always wear safety goggles or safety glasses with side shields when operating tool. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury . DRILLING See Figure 12. When drilling hard, smooth surfaces, use a center punch to mark the desired hole location. This wi[...]

Page 12 7 6 7 6 7 6 OPERA TION Fig. 13 Fig. 14 Fig. 15 CHUCK REMOV AL See Figures 13, 14, and 15. The chuck must be removed in order to use some accessories. T o remove: ■ Lock the switch trigger by placing the direction of rotation selector in center position. ■ Insert a 5/16 inch or larger allen wrench (hex key wrench) into the chuck of your [...]

Page 13 MAINTENANCE W ARNING: When servicing use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage. A void using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use a clean cloth to remove[...]

OPERA T OR'S MANUAL CORDLESS DRILL-DRIVER MODEL NOS. R Y721/R Y961/R Y1201 R YOBI AMERICA CORP . 1424 Pearman Dairy Road Anderson, SC 29625 Post Office Box 1207 Anderson, SC 29622-1207 Phone 1-800-525-2579 R YOBI CANADA INC. Post Office Box 910 Cambridge, Ontario N1R 6K2 Phone 1-800-265-6778 972000-570 9-00 RY721/RY961/RY1201 • SER VICE Now [...]