Samsung HL-P5667W инструкция обслуживания

Remote Control (BP59-00076A)/ AAA Batteries Once you have unpacked your TV , check to make sure that you have all the parts shown here. If any piece is missing or broken, call your dealer . Accessories Instruction Manual/ Safety Guide/ Quick Guide/ Anynet Manual / Manual Guide W arranty Cards (2)/ Registration Card (1) Anynet Cable List of Parts BP[...]

Connecting VHF and UHF Antennas 1 Place the wires from the twin leads under the screws on the 300-75 ohm adaptor (not supplied). Use a screwdriver to tighten the screws. 2 Plug the adapter into the “Air IN” terminal on the rear panel. If you do not have a cable system, you will need to connect an antenna to your TV . Antennas with 300-ohm Flat [...]

Connecting Cable TV and VCR • When you use a converter box with your TV , there may be fea- tures that you can not program using the remote control, such as programming your favorite channels and blocking chan- nels. • The output from "Cable Out" is not available when "Air/CA TV" is set to "Cable" in the PIP menu. [...]

Connecting CableCARD 1 2 Insert the CableCARD into the “CableCARD” slot and the message “CableCARD Inserted” is displayed on the screen. If the channel information does not already exist, the message “Updating Channel List” is displayed during channel information configura- tion. The pairing information containing a telephone number , C[...]

Connecting a DVD Player Connecting a Camcorder 1 2 Locate the A/V output jacks on the camcorder . They are usually found on the side or back of the camcorder . Connect a set of audio cables between the AUDIO IN jacks on the TV and the AUDIO OUT jacks on the camcorder . If you have a mono Camcorder , connect L(mono) to the Camcorder audio out using [...]

Connecting a DTV Set-T op Box 1 2 Connect a set of audio cables between the Audio in (1 or 2) jacks on the TV and the AUDIO OUT jacks on the DVD player . Connect a video cable between the VIDEO IN (1 or 2) jack on the TV and the VIDEO OUT jack on the DVD player . Connecting to Audio and V ideo Jacks 1 2 Connect a set of audio cables between the COM[...]

Connecting to HDMI (High Definition Multimedia Interface) 1 2 Connect a set of audio cables between the DVI audio (L,R) in jacks on the TV and the AUDIO OUT jacks on the Set-T op Box. Connect an HDMI/DVI video cable between the HDMI/DVI IN jack on the TV and the DVI OUT jack on the Set-T op Box. Connecting to DVI (Digital Visual Interface) 1 Connec[...]

Connecting to an Analog Amplifier Connecting a Digital Audio System 1 If your audio system has a optical dig- ital audio input, connect to the “DIGI- TA L AUDIO OUT(OPTICAL)” jack on the TV . Be certain to remove the black cover from the optical output before insert- ing the cable. There are many types of digital audio systems on the market tod[...]

Remote Control Œ POWER T urns the TV on and off. ´ P .MODE Adjust the TV picture by selecting one of the preset factory settings (or select your personal, customized picture settings.) ˇ ANTENNA Press to select “AIR” or “CABLE”. ¨ CHANNEL NUMBER Press to directly tune to a particular channel. ˆ - Press to select additional channels (di[...]

T urning the TV On and Off Press the POWER button on the remote control. Y ou can also use the POWER button on the front panel. V iewing the Menus and On-Screen Displays The on-screen menu system allows you to control the settings of your TV . Access the on- screen menu system by pressing the Menu button on the remote control. Once the on- screen m[...]

Memorizing the Channels Y our TV can memorize and store all of the available channels for both “off-air” (antenna) and cable channels. After the available channels are memorized, use the CH and CH buttons to scan through the channels. This eliminates the need to change channels by entering the channel digits. There are three steps for memorizin[...]

4 Press the … or † button to select the Antenna connection, then press the ENTER button. • Air : “Air” antenna signal Cable : “Cable” antenna signal Air+Cable : “Air” and “Cable” antenna signals • If the CableCARD is inserted into the“CableCARD” slot on the rear panel, “Cable” and “Air+Cable” are not avail- able.[...]

V iewing an External Signal Source Use the remote control to switch between viewing signals from connected equipment, such as a VCR, DVD, Set-T op box or the TV source (broadcast or cable). V iewing Position To optimize your viewing comfort, please follow the guidelines below for viewing distance. If viewing for an extended period of time, sit as f[...]

Replacing the Lamp Why do I need to replace the lamp? The lamp used in a DLP TV has a limited lifespan. For the best screen quality it needs to be replaced periodically . After replacing the lamp, the screen quality will be bright and clear as new . When do I need to replace it? It should be replaced when the screen becomes darker , less clear or w[...]

Front Panel LED Indicators The three lights on the front panel indicate the status of your TV . : Light is On : Light is Blinking : Light is Off • It takes about 30 seconds for the TV to warm up, so normal brightness may not appear imme- diately . • The TV has a fan to keep the inside lamp from overheating. Y ou’ll occasionally hear it workin[...]

Memo 16 BP68-00429A-00Eng 11/10/04 3:18 PM Page 16[...]