Samsung ML-1651N инструкция обслуживания

Home Visit us at: http://www .samsungprinter .com P/N. JC68-00694A Rev .1.00 ML-1650 Series User’s Guide[...]

This manual is provided for information purposes only . All information included herein is subject to change without notice. Samsung Electronics is not responsible for any damages, direct or indirect, arising from or related to use of this manual. © 2001 Samsung Electronics Co. , Ltd. All rights reserved. • ML -1650, ML -1651N and Samsung logo a[...]

Special Features –––––––––––––––––––––––––––––––––––––––––––– 1.1 Printer Components ––––––––––––––––––––––––––––––––––––––––– 1.4 Control P anel Buttons ––––––––?[...]

3 Printing a Document ––––––––––––––––––––––––––––––––––––––– 5.1 Using T oner Sav e Mode –––––––––––––––––––––––––––––––––––– 5.6 Printing on Both Sides of the P aper (Manual Duplexing) ––––?[...]

4 Contents (continued) Printer Specifications –––––––––––––––––––––––––––––––– A.1 P aper Specifications ––––––––––––––––––––––––––––––––– A.2 A Specifications Installing the Printer Software –––––––––?[...]

5 F Using Y our Printer on a Network Making Installation Diskettes –––––––––––––––––––––––– G.1 Installing Software from Diskettes ––––––––––––––––––– G.3 About Sharing the Printer on a Network –––––––––––––– F. 1 Setting Up a Locally S[...]

6 En vir onmental and Saf ety Consider a tion Laser Saf ety Sta tement The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR, chapter 1 Subchapter J for Class I(1) laser products, and elsewhere, is certified as a Class I laser product conforming to the requirements of IEC 825. Class I laser products are not considered t[...]

7 Ozone Saf ety During normal operation, the ML -1650 Series printer produces ozone. The ozone produced does not present a hazard to the operator . Howev er , it is advisable that the machine be operated in a well ventilated area. If you need additional information about ozone, please contact your nearest Samsung dealer . OZONE P ow er Sa v er En v[...]

8 FCC regulations This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can r adiate radio frequency energy and, if no[...]

9 Declaration of Conformity (European Countries) Approvals and Certifications The CE marking applied to this product symbolises Samsung Electronics Co. , Ltd. Declaration of Conformity with the following applicable 93/68/EEC Directives of the European Union as of the dates indicated: January 1, 1995: Council Directive 73/23/EEC Approximation of the[...]

Congratulations on the purchase of y our ML -1650 series printer! This chapter provides information on the following topics: ◆ Special F eatures ◆ Printer Components 1 1[...]

I NTRODUCTION 1. 1 Special F eatures Y our new Samsung ML -1650 series printer is equipped with special features that improve print quality , giving you a competitive edge. Y ou can: • Prints at 1200 dots per inch (dpi). See page 5.19. • Prints 16 pages-per-minute(A4 size), 17 pages-per- minute(Letter size) . • The PCL 6 printer language enab[...]

1. 2 I NTRODUCTION 1. 2 Special F ea tures • Allows you to use the Toner Save mode to save toner . See page 5.6. • Allows you to print on both sides of the paper to sav e paper ( Manual Duplexing ). See page 5.7. • Allows you to print multiple pages on one single sheet of paper to save paper ( N-Up printing ). See page 5.10. • Preprinted fo[...]

1. 3 I NTRODUCTION Special F ea tures • Prints in Windows , DOS , and Macintosh . • Supports Linux . • ML -1650 series printer comes with Parallel and USB. Yo u can install an optional network interface (ML -1651N have a built-in network interface). Print in various environments T able below lists a general overview of features supported by t[...]

1. 4 I NTRODUCTION Printer Components F r ont V iew Control panel Top output tray Control board cover (needed to access the control board to install printer options) Paper level indicators (Inside) (F ace down output ) Top cover Tray 1 (550-sheet paper feeder) Multi-Purpose Tray Tray 2 (Optional 550-sheet paper feeder) T oner cartridge[...]

I NTRODUCTION 1. 5 Printer Components (F ace up output) R ear V iew Power switch Rear output tray door Power receptacle Parallel port USB port Network port (ML -1650: Option ML -1651N: Standard)[...]

This chapter provides step by step information on setting up your printer . T opics included in this chapter are: ◆ step 1 : Unpack Y our Printer ◆ step 2 : Install the T oner Cartridge ◆ step 3 : Load P aper ◆ step 4 : Connect to the Computer with a P arallel Cable ◆ step 5 : T urn on the Printer ◆ step 6 : Print a Demo P age! ◆ step[...]

2. 1 S ETTING U P Y OUR P RINTER Unpac k Y our Printer 1 R emove the printer and all accessories from the packing carton. Make sure that your printer has been packed with the following items: Notes: • If any items are missing or damaged, notify your dealer immediately . • Components may differ from one country to another . • The CD-ROM contai[...]

2. 2 S ETTING U P Y OUR P RINTER Unpack Y our Printer Selecting a Loca tion Select a level, stable place with adequate space for air circulation. Allow extr a space for opening covers and tr ays. The area should be well- ventilated and aw ay from direct sunlight or sources of heat, cold, and humidity . See the image below for clearance space. Do no[...]

2. 3 S ETTING U P Y OUR P RINTER 1 Open the top cover lid. Pull up on the handle to open the lid. 2 Carefully tear one end of the plastic bag. Don’t use a knife or other sharp objects as they might scratch the drum of the cartridge. 3 Locate the sealing tape at the end of the toner cartridge. Carefully pull the tape completely out of the cartridg[...]

2. 4 S ETTING U P Y OUR P RINTER Note: When printing text at 5% coverage, you can expect a toner cartridge life of approximately 8,000 pages (4,000 pages for the toner cartridge that is shipped with the printer). 6 Grasp the handle and insert the cartridge in the printer until it drops into place. 7 Close the top cover . Make sure that the cover is[...]

2. 5 S ETTING U P Y OUR P RINTER 1 Pull the paper tra y out of the printer . 3 Load paper with the print side facing down . Make sure that all four corners are flat in the tra y . 2 Push down on the metal paper lift plate to lock it in place. Load P aper[...]

2. 6 S ETTING U P Y OUR P RINTER 5 Slide the tra y back into the printer . Note: If you want to change the paper size in the tray , refer to: “T o Change Paper Size in T ray” 1 Squeeze the metal tab on the rear paper guide to adjust for the paper length. T o Change Paper Siz e in T r ay 4 Make sure that the stack goes under the metal retaining [...]

2. 7 S ETTING U P Y OUR P RINTER 3 After loading paper , squeeze the side guide as shown and slide it to the left flush against the paper . Notes: • Do not push the width guide far enough to cause the media to warp. • If you do not adjust the width guide, it may cause a paper jam. 4 If necessary , use the rear width guide. Squeeze the rear widt[...]

2. 8 S ETTING U P Y OUR P RINTER 1 Make sure that both the printer and the computer are turned off . 2 Plug the parallel printer cable into the connector on the back of the printer . Push the metal clips down to fit inside the notches on the cable plug. 3 Connect the other end of the cable to the parallel interface port on y our computer , and tigh[...]

2. 9 S ETTING U P Y OUR P RINTER 1 Plug the power cord into the power receptacle on the back of the printer . 2 Plug the other end into a properly grounded AC outlet. 3 T urn on the power . T ur n on the Printer ➞ To AC outlet As the printer powers up, all the printer control panel lights turn on briefly . When only the Data light remains on, pre[...]

Included with your printer is a CD-ROM containing the printer drivers for some of the most popular Windows software applications. T o oper ate your printer , you must install a printer driver , which translates data from your application into data that the printer understands. The CD-ROM shipped with your printer contains the following: • PCL 6 p[...]

2. 11 S ETTING U P Y OUR P RINTER V erify the following: • At least 32 MB or more of RAM is installed on your PC. • There is at least 200 MB of free disk space on your PC. • All applications are closed on your PC before beginning installation. • Windows 95, Windows 98, Windows Me, Windows NT 4.0 or Windows 2000. 1 Place the CD-ROM in the CD[...]

2. 12 S ETTING U P Y OUR P RINTER Install the Printer Software 3 Click Install the Samsung Software on your PC . 2 When the opening screen appears, select the appropriate language.[...]

2. 13 S ETTING U P Y OUR P RINTER Install the Printer Software 4 The W elcome window opens. Click Next . 5 F ollow the instructions on the screen to complete the installation.[...]

2. 14 S ETTING U P Y OUR P RINTER Install the Printer Software ML -1650 series printer drivers will support the following standard features: • Input tr ay selection • paper size, orientation and media type • number of copies T able below lists a general overview of features supported by the ML -1650 series printer drivers. Printer Driv er F e[...]

2. 15 S ETTING U P Y OUR P RINTER If you have access to another computer with a CD-ROM driv e, you can use the make disk ette utility in Windows to create the disks you need for the installation. Go to Appendix G, “Installing Software from Diskettes” . In Windows, after installation, the Uninstall icon in the ML -1650 series program group allow[...]

This chapter describes how to use the printer’s control panel. It provides information on the following topics: ◆ Control P anel Buttons ◆ Control P anel Lights 3 3[...]

Contr ol P anel Buttons The printer has three buttons: Cancel/Reprint , Demo and Toner Save . Press Toner Save to turn the toner save mode on or off . The printer must be in the ready mode. • If the button backlight is on, toner save mode activates and the printer uses less toner to print a document. • If the button backlight is off , toner sav[...]

Control Panel Buttons Reprint last page of the job Press Cancel/Reprint and hold until the control panel lights blink to cancel a job the printer is currently printing. The Error light will blink while the print job is cleared from both the printer and the computer , and the printer will then return to the ready mode. This may take some time, depen[...]

Cleaning the inside of the printer Press and hold Demo for about 2 seconds until the control panel lights blink slowly to print a demo page. The printer must be in the ready mode. Press and hold Demo for about 6 seconds until the control panel lights blink rapidly to print a configur ation sheet. The printer must be in the ready mode. For further i[...]

The printer is receiving or processing data. W ait for the job to print. Pressing the Cancel/Reprint button cancels the current job. One or two pages may print as the printer clears the print job. The printer will return to the ready mode after the job has been canceled. Processing The Data light blinks rapidly . Data is in the printer memory waiti[...]

Control Panel Lights The printer is out of paper . The Paper light blinks until paper is added. Load paper into the printer . There is no need to press any button to reset. Paper out The printer is processing data in the Manual Feed mode. W ait for the job to print. Printing in the manual feed mode The printer is set to Manual Feed mode. Y ou have [...]

This chapter will help you understand what kind of paper you can use with the ML -1650 series printer and how to properly load paper in the different paper tra ys for the best print quality . T opics included in this chapter are: ◆ Choosing P aper and Other Media ◆ Selecting the Output T r a y ◆ Loading P aper ◆ Printing on Env elopes ◆ P[...]

4. 1 P RINT M EDIA Choosing P aper and Other Media Y ou can print on a variety of print media, such as plain paper , envelopes, labels, tr ansparencies, card stocks and so on. See “P aper Specifications” on page A.2. T o get the best possible print quality , use only high-quality copier-grade paper . When you choose print media, consider the fo[...]

4. 2 P RINT M EDIA Choosing Paper and Other Media Plain Paper Letter (8.5 x 11 in.) Legal (8.5 x 14 in.) Executive (7.25 x 10.5 in.) F olio (8.5 x 13 in.) A4 (210 x 297 mm) B5 (182 x 257 mm) A5 (148 x 210 mm) Envelopes No. 10 (4.12 x 9.5 in.) Monarch (3.87 x 7.5 in.) C5 (162 x 229 mm) DL (110 x 220 mm) B5 (176 x 250 mm) Labels* 2 Letter (8.5 x 11 i[...]

When selecting or loading paper , envelopes, or other special media, keep these guidelines in mind: • Attempting to print on damp, curled, wrinkled, or torn paper can cause paper jams and poor print quality . • Use cut-sheet paper only . Y ou cannot use multi-part paper . • Use only high-quality , copier grade paper . • Do not use paper tha[...]

4. 4 P RINT M EDIA Selecting the Output T r ay The printer has two output locations: the rear output tray and the top output tray . T o use the top output tra y , be sure the rear output tray is closed. T o use the rear output tray , open it. • If paper coming out of the top output tra y has problems, such as excessive curl, try printing to the r[...]

4. 5 P RINT M EDIA Selecting the Output T r ay 1 Open the rear door by pulling it down . The cover functions as the output tr ay . To open the rear output tray: 2 Pull the extender to extend the output tra y to its full-length position. This will allow the tra y to hold longer paper . 3 If you do not want to stack the printed pages on the rear outp[...]

4. 6 P RINT M EDIA Loading P aper T ray 1 holds 550 sheets of paper . See “Media Sizes and Capacities” on page 4.2 for acceptable paper size and capacities of each trays. Load a stack of paper into the T ray 1 or optional T ray 2 and print. For details on loading paper in the T ray 1 or optional T ray 2, see “Load P aper” on page 2.5. Prope[...]

4. 7 P RINT M EDIA Loading Paper The Multi-Purpose T ray is located in the front of y our printer . It can be closed when you are not using it, making the printer more compact. The Multi-Purpose T ray can hold sev eral sizes and types of paper , such as transparencies, cards, and envelopes. Y ou may also want to use the Multi-Purpose T ray for sing[...]

4. 8 P RINT M EDIA 1 Pull the Multi-Purpose T ra y down towards you. T o load paper in the Multi-Purpose T ray: 2 Slide the extender to extend the tra y to its full-length position to hold longer paper . 3 Prepare a stack of paper for loading by flexing or fanning them back and forth. Straighten the edges on a lev el surface. Loading Paper[...]

Note: Make sure that you have not loaded too much print media. The stack should be under the stack height limit mark. The print media buckles if you load a stack that is too deep, or push it in too far . 4. 9 P RINT M EDIA Loading Paper 4 Place paper with the print side face up , and against the left edge of the tra y . 5 Slide the paper width guid[...]

4. 10 P RINT M EDIA Loading Paper When you change the print settings, if you select Manual Feed in the Paper Source option, you can manually load paper in the Multi-Purpose T ray . Manually loading paper can be helpful when you want to check the print quality after each page is printed. This loading procedure is almost the same as the procedure for[...]

4. 11 P RINT M EDIA Loading Paper 4 Print the document. 5 The Manual light on the control panel blinks. Press the Demo button on the control panel. The sheet of paper is loaded and printed. 6 After one page is printed, the Manual light on the control panel blinks again. F eed the next sheet into the Multi- Purpose T ra y and press Demo . R epeat th[...]

P RINT M EDIA 4. 12 Printing on En v elopes Guidelines • Only use env elopes recommended for laser printers. Before you load envelopes in the Multi-Purpose T ray , make sure that they are undamaged and are not stuck together . • Do not load more than 10 envelopes into the Multi-Purpose T ray . • Do not feed stamped env elopes. • Never use e[...]

P RINT M EDIA 4. 13 Printing on En v elopes 4 Load the envelopes with the flap side down , and against the left edge of the tra y . The stamp area is on the left side and the end of the envelope with the stamp area enters the Multi-Purpose Tray first . 5 Adjust the guide to the left edge of the envelope stack. 3 Flex or fan the envelopes to supply [...]

P RINT M EDIA 4. 14 Printing on Labels Guidelines • Only use labels recommended for laser printers. • Do not load more than 25 labels into the Multi-Purpose T ra y at a time. • V erify that the labels’ adhesive material can tolerate fusing temper ature of 200°C (392°F) for 0.1 second. • Make sure that there is no exposed adhesive materi[...]

P RINT M EDIA 4. 15 Printing on T r anspar encies Guidelines • Only use tr ansparencies recommended for use in laser printers. • Do not load more than 20 transparencies into the Multi-Purpose T ray at a time. • Make sure that the tr ansparencies are not wrinkled or curled, and that they do not have any torn edge. • Hold the tr ansparencies [...]

P RINT M EDIA 4. 16 Printing on Pr eprinted P aper XXXXXXXXXX 1 Load letterheads into the tra y you want to use as shown in the figures. Adjust the guide to fit the width of the paper stack. 2 When you print a document on the paper , configure the paper source, type and size in the software application. F or details, see page 5.3. Preprinted paper [...]

P RINT M EDIA 4. 17 Printing on Car d Stoc k or Custom-sized Media 1 Open the Multi-Purpose T ra y and the rear output tra y and pull the extenders out to its full-length position. 2 Load print media with print side up , short edge first and against the left edge of the tra y . Adjust the guide to fit the width of the media. 3 Configure the paper s[...]

This chapter explains your printing options and cov ers common printing tasks. T opics included in this chapter are: ◆ Printing a Document ◆ Using T oner Save Mode ◆ Printing on Both Sides of the P aper (Manual Duplexing) ◆ Printing Multiple Pages on One Sheet of P aper (N-Up Printing) ◆ Printing Booklets ◆ Printing on Different P aper [...]

5. 1 P RINTING T ASKS Printing a Document The following procedure describes the general steps required for printing from various Windows applications. The exact steps for printing a document may v ary depending on the application program y ou are using. Refer to your softw are application’ s documentation for the exact printing procedure. 1 Open [...]

5. 2 P RINTING T ASKS Printing a Document 3 T o take full adv antage of the printer features provided by your ML -1650 series printer , click Properties in the application’ s Print dialog box and go to step 4. If you see Setup , Printer , or Options , click that button instead. Then click Properties in the next screen. 4 Now you see the Samsung M[...]

5. 3 P RINTING T ASKS Printing a Document Make sure the Paper Source is set to Tray 1 . If you use paper in the Multi-Purpose T ray or optional T ray 2, select the corresponding paper source. Manual Feed source is used when printing to special media. Y ou have to feed one sheet at a time into the printer . See page 4.10. If the paper source is set [...]

5. 4 P RINTING T ASKS 5 Click other tabs on the top of the Properties dialog box to access other features, if needed. 6 When you complete the print settings, click OK until the Print dialog box is display ed. 7 Click OK to start printing. • Most Windows applications will override settings you specify in the printer driver . Change all print setti[...]

5. 5 P RINTING T ASKS There are two ways to stop a print job. To stop a print job from the ML-1650 series printer Press the Cancel/Reprint button on the control panel. The printer will finish printing the page that is moving through the printer and delete the rest of the print job. Pressing Cancel/Reprint cancels only the current job in the printer[...]

5. 6 P RINTING T ASKS Using T oner Sa v e Mode T oner Save mode allows the printer to use less toner on each page. Selecting this option will extend the life of your toner cartridge and reduce your cost per page, but will reduce print quality . This setting is not available with 1200 dpi settings. There are two ways to enable the T oner Save mode. [...]

5. 7 P RINTING T ASKS Printing on Both Sides of the Paper (Manual Duple xing) T o print on both sides of the paper (manual duplexing), you must run the paper through the printer twice. Y ou can print using the top output tra y (face down tray) or the rear output tra y (face up tray). Samsung recommends using the top output tra y for light-weight pa[...]

5. 8 P RINTING T ASKS 3 Select Face Down Tray (top output tray) or Face Up Tray (rear output tra y) in which the printed media is to be stacked. According to this option, the printer will determine the print page order when the second sides are printed. 4 If you want to print the instruction page which tells you how to load the paper , click Printi[...]

8 Y ou are prompted to reinsert the paper into the Multi- Purpose T ray . Click OK on the screen to start printing the second side. The printer automatically prints only the even- numbered pages. 5. 9 P RINTING T ASKS 6 After the first side has been printed, remove the remaining paper from the Multi-Purpose T ray and set it aside until after you fi[...]

5. 10 P RINTING T ASKS 1 2 3 4 Y ou can select the number of pages that you want to print on a single sheet of paper . If you choose to print more than one page per sheet, the pages will appear decreased in size and arranged on the sheet. Y ou can specify up to 16 pages. 1 When you change the print settings from your software application, access th[...]

P RINTING T ASKS 5. 11 " " Portrait orientation Printing Booklets 8 9 " " Landscape orientation 7 1 9 The Booklet printing feature allows you to print your document as a 2-sided (duplex) job and to arrange the pages so that the paper can be folded in half after printing to produce a booklet. 1 When you change the print settings [...]

5. 12 P RINTING T ASKS Printing Booklets 3 Select Face Down Tray (top output tray) or Face Up Tray (rear output tra y) in which the printed media will be stacked. According to this option, the printer will determine the print page order when the second sides are printed. 4 If you want the instruction page which tells you how to load the paper , cli[...]

P RINTING T ASKS 5. 13 Printing Booklets 7 Gather up the printed pages, flip the stack, and then straighten the stack before placing it back in the multi- purpose tra y . The following illustrations show how to put the paper back into the printer . Note: If you have selected the Face Up tray option at Step 3, the last page is placed on the top of t[...]

5. 14 P RINTING T ASKS Printing on Dif f er ent P aper f or the Fir st P age 1 When you change the print settings from your software application, access the printer properties. See page 5.2 to access the printer properties. 2 Click the Paper tab, and click Different Source for First Page . If the box is checked, this feature is enabled and the dial[...]

P RINTING T ASKS 5. 15 Fitting Y our Document T o a Selected Paper Size This printer feature allows you to scale your print job to any selected paper size regardless of the digital document size. This can be useful when you want to check fine details on a small document. 1 When you change the print settings from your software application, access th[...]

5. 16 P RINTING T ASKS Printing P oster s This feature allows you to print a single-page document onto 4, 9, or 16 sheets of paper , for the purpose of pasting the sheets together to form one poster-size document. 1 When you change the print settings from your software application, access the printer properties. See page 5.2 for more information on[...]

P RINTING T ASKS 5. 17 Printing P oster ➛ ! ! ➛ ! ! 2 x 2 " ! ! " ! ! Overlap=0 " ! ! " ! ! Overlap=25 25 pixels 25 pixels ➛ ! ! ➛ ! ! Custom (150%) 5 Click OK , then start printing. 3 T o determine the scaling factor , select the Style ; 2x2 , 3x3 , 4x4 or Custom . F or example, if you select 2x2 , the output will be au[...]

5. 18 P RINTING T ASKS Use the following options to adjust the print quality for your specific printing needs when you access the printer properties. See page 5.2 for more information on accessing printer properties. If necessary , click the Graphic tab to display the settings shown below . Setting Gr a phic Pr oper ties 5. 18 P RINTING T ASKS[...]

P RINTING T ASKS 5. 19 Y ou can select the printing resolution; 1200 dpi , 600 dpi , 300 dpi . The higher the setting, the sharper the clarity of printed characters and gr aphics. Higher settings may increase the time it takes to print a document. Some printed characters or images can appear to hav e jagged or uneven edges. Set this Samsung R esolu[...]

5. 20 P RINTING T ASKS This option can be used for configuring the halftone of the printed illustration. The best w ay to choose a Halftoning setting for your gr aphic image is to experiment. Print a graphic image at each setting and choose the one you like best. • Device – Choose this setting for printed graphic image that printer provides. ?[...]

P RINTING T ASKS 5. 21 Printing W a ter mar ks The W atermark option allows you to print text over an existing document. For example, y ou may want to hav e large gray letters reading “DRAFT” or “CONFIDENTIAL” printed diagonally across the first page or all pages of a document. There are sever al predefined watermarks that come with the ML [...]

5. 22 P RINTING T ASKS Printing Wa ter mar ks 1 When you change the print settings from your software application, access the printer properties. See page 5.2 for more information on accessing the printer properties. 2 Click the Watermark tab, and enter the desired text message in the Text field. This will be displayed in the preview window . The p[...]

P RINTING T ASKS 5. 23 Printing Wa ter mar ks 4 If you have created a new or edited an existing w atermark, the Add and Update button is enabled. T o add a new watermark to the list, click Add . 5 If you want to edit, select the desired watermark from the list, edit, then click Update . 6 When you complete the edit, click OK , then start printing. [...]

5. 24 P RINTING T ASKS Using P a ge Ov er lay An overlay is text and/or images stored in the computer HDD as a special file format that can be printed on any document you choose. Overlays are often used to tak e the place of preprinted forms and letterhead paper . Rather than using preprinted letterhead, for example, you can create an overla y cont[...]

P RINTING T ASKS 5. 25 4 In the Create Overlay dialog box, type a name of up to eight characters in the File name box. Select the destination path if necessary . (The default is C:FORMOVER). 5 Click OK . Y ou will see the name in the Overlay List box. 6 Click OK or Yes until you complete the creation. The file is not printed out. Instead it will b[...]

5. 26 P RINTING T ASKS 4 If the desired overlay file does not appear in the Overlay List box, click Load Overlay , and select the overlay file. If you have stored the o verlay file you w ant to use into an external source, you can also load the file when you access this Load Overlay window . After you select the file, click OK . The file is now sho[...]

P RINTING T ASKS 5. 27 Y ou can delete page overlays that are no longer used. 1 In the printer properties dialog b o x, click the Overlay ta b . 2 Select the overlay y ou want to delete from the Overlay List box. 3 Click Delete Overlay . 4 Click OK until you exit the Print dialog box. Deleting a Page Overlay 5 If necessary , click Query Page Overla[...]

This chapter provides suggestions for high-quality and economical printing and information for maintaining the toner cartridge and the printer . T opics included in this chapter are: ◆ Maintaining T oner Cartridge ◆ Cleaning the Printer 6 6[...]

6. 1 M AINT AINING Y OUR P RINTER Maintaining T oner Car tridge T o get the most from the toner cartridge, keep the following guidelines in your mind. • Do not remov e the toner cartridge from its package until you are ready to use it. The shelf life of a cartridge in an unopened package is approximately 2 years. The shelf life of a cartridge in [...]

6. 2 M AINT AINING Y OUR P RINTER T oner Car tridge When toner is low , faded or light areas may appear on a printed page. Y ou may be able to temporarily improv e print quality by redistributing the toner . The following procedures may allow you to finish the current print job before replacing the toner cartridge. R edistributing T oner 1 Open the[...]

6. 3 M AINT AINING Y OUR P RINTER T oner Car tridge 4 R einsert the toner cartridge into the printer . Be sure that the toner cartridge is firmly in its place. 5 Firmly close the cover . If the print remains light R emove the old cartridge and install a new toner cartridge. See “Install the T oner Cartridge” on page 2.3.[...]

6. 4 M AINT AINING Y OUR P RINTER Cleaning the Printer T o maintain print quality , follow the cleaning procedures below every time the toner cartridge is replaced or whenever print quality problems occur . As much as possible, keep the printer free from dust and debris. Notes: • Do not use ammonia-based cleaners or volatile solvents such as thin[...]

3 Y our printer automatically picks up a sheet of paper from the paper tra y and prints out a cleaning sheet with the dust or toner particles on it. 6. 5 M AINT AINING Y OUR P RINTER 5 R einsert the toner cartridge and close the top cover . Then, turn the printer on. Cleaning the Printer Printing a cleaning sheet Printing a cleaning sheet cleans th[...]

This chapter gives helpful information for what to do if you encounter a printer error . It provides information on the following topics: ◆ T roubleshooting Checklist ◆ Solving Gener al Printing Problems ◆ Printing Special P ages ◆ Clearing P aper Jams ◆ Solving Print Quality Problems ◆ T roubleshooting Error Messages ◆ Common Windows[...]

7. 1 P ROBLEM S OL VING T r oubleshooting Chec klist If the printer is not working properly , complete the following checklist in order . If the printer does not pass a step, follow the corresponding troubleshooting suggestions. Check Make sure that the Data light on the control panel is on. Press the Demo button to print a demo page to verify that[...]

7. 2 P ROBLEM S OL VING Solving Gener al Printing Pr oblems Problem The printer does not print. Possible Cause The printer is not receiving power . Y our printer is not selected as the default printer . Check the printer for the following: The printer may be in manual feed mode and out of paper . (The Manual and the Data lights are blinking.) The c[...]

7. 3 P ROBLEM S OL VING Solving General Printing Pr oblems Problem The printer does not print. (continued) Printer selects media from the wrong paper source. P aper does not feed into the printer . Print job is extremely slow . Possible Cause The printer may be configured incorrectly . The printer driver may be incorrectly installed. The printer is[...]

7. 4 P ROBLEM S OL VING Solving General Printing Pr oblems Problem Print job is extremely slow . (continued) Half of the page is blank. The paper keeps jamming. Possible Cause The computer may have insufficient random- access memory (RAM). The page layout is too complex. The page orientation setting may be incorrect. The paper size and the paper si[...]

7. 5 P ROBLEM S OL VING Solving General Printing Pr oblems Problem The printer prints, but the text is wrong, garbled, or incomplete. P ages print, but are totally blank. Possible Cause The printer cable is loose or defective. The wrong printer driver was selected. The software application is malfunctioning. The operating system is malfunctioning. [...]

7. 6 P ROBLEM S OL VING Printing Special P a ges There are special pages within the memory of the printer that will help you to diagnose and learn about problems with your printer . Use the Demo button on the printer control panel to print these special pages. The printer must be in the ready mode. Printing the demo page will help you check if the [...]

7. 7 P ROBLEM S OL VING Clearing P aper J ams Occasionally , paper can become jammed during a print job. Some of the causes include: • The paper tra y is loaded improperly or overfilled. • The paper tra y has been pulled out during a print job. • The top cover has been opened during a print job . • P aper that does not meet paper specificat[...]

7. 8 P ROBLEM S OL VING Clearing Paper J ams 4 If there is resistance when you pull the paper , squeeze the handle on the right end of the exit roller , then pull the roller in the direction of arrow . 3 R emove the stopper fastening the rear output tra y , and push the tray down so that it is open at 90 degrees angle. 2 If the jammed paper is not [...]

7. 9 P ROBLEM S OL VING Clearing Paper J ams 7 R eplace the stopper and close the rear output tra y . 1 2 6 R eplace the exit roller . Make sure that you click the right end of the roller back in place. If you fail to do so, the printer system will recognizes that the printer cover is open or that a system fuser error has occurred, and the Error li[...]

P ROBLEM S OL VING Clearing Paper J ams 2 R emove any misfed paper by pulling it out by the visible edge from the tra y . Make sure that all of the paper is properly aligned in the tra y . Note: If paper has entered the toner cartridge area, follow the instructions on page 7.12. It is easier to remove such jams from the inside of the printer than t[...]

P ROBLEM S OL VING Clearing Paper J ams 3 Slide the tra y back into the printer . 4 T o resume printing, open the top cov er , and then close in again. Note: If the Paper and the Error lights do not turn off, there is still jammed paper inside the printer . Check the inside of the printer . 7. 11[...]

P ROBLEM S OL VING Clearing Paper J ams 2 Carefully lift up the guide feed. 3 Gently pull the paper toward you to remove it from the printer . CAUTION: T o prevent damage to the toner cartridge, do not expose it to light for more than a few minutes. Place a piece of paper over the top of the toner cartridge to shield it while it is out of the print[...]

Clearing Paper J ams 5 Close the top cover . Printing can be resumed. 4 Flip down the guide feed, and reinstall the toner cartridge. Note: If the toner cartridge is difficult to reinstall, make sure the guide feed has been flipped back down into position. Note: If you have the optional T ray 2 installed, and cannot find the jammed paper in the outp[...]

P ROBLEM S OL VING Clearing Paper J ams 3 If you cannot find the jammed paper in the T ra y 2, pull the upper T ra y 1 half way out of the printer , and remove the paper as shown in the figure at right. In the Optional T r ay 2 1 Pull the option T ra y 2 out of the printer . 2 If you see the jammed paper , remove the paper from the tra y . 4 Slide [...]

Clearing Paper J ams Tips f or A v oiding Paper J ams By selecting correct paper types and loading them properly , you should be able to avoid most paper jams. If paper jams occur , follow the steps outlined in “Clearing P aper Jams” on page 7.7. If jams occur frequently , make sure you are following these tips to avoid jams. • F ollow the pr[...]

P ROBLEM S OL VING 7. 16 Problem Solution Solving Print Quality Pr oblems General print quality problems can be solved by following the checklist below . • Check the printer properties to make sure that y ou are using the best av ailable print quality option (see page 5.18). • R edistribute the toner in the toner cartridge (see page 6.2). • C[...]

Problem Solution P ROBLEM S OL VING 7. 17 Solving Print Quality Problems • The paper may not meet paper specifications (for example, the paper is too moist or too rough). See “P aper Specifications” on page A.2. • The transfer roller ma y be dirty . See “Cleaning the Inside” on page 6.4. • The paper path may need cleaning. See “Clea[...]

P ROBLEM S OL VING 7. 18 Problem Solution If the amount of background toner shading becomes unacceptable, the procedures below may help to clear the condition: • Change the paper to a lighter basis weight. See “P aper Specifications” on page A.2. • Check the printer’s en vironment; very dry (low humidity) or high humidity (higher than 80 [...]

Problem Solution P ROBLEM S OL VING 7. 19 • If char acters are improperly formed, producing hollow images, the paper stock may be too slick. T ry a different paper . See “Paper Specifications” on page A.2. • If char acters are improperly formed, producing a wavy effect, the scanner unit may need service. Check to see if it also occurs on a [...]

P ROBLEM S OL VING 7. 20 Problem Solution Solving Print Quality Problems • Check the paper type and quality . Both high temperature and humidity will cause paper curl. See “P aper Specifications” on page A.2. • T urn over the stack of paper in the paper tr ay . Also try rotating the paper 180° in the paper tra y . • Open the rear output [...]

Problem Solution P ROBLEM S OL VING 7. 21 Solving Print Quality Problems Character v oids are white areas within the parts of characters that should be solid black: • If you are using tr ansparencies when you experience this problem, try another type of tr ansparency . (Because of the composition of transparency media, some char acter voids are n[...]

P ROBLEM S OL VING 7. 22 When the printer detects an error , the control panel indicator lights will indicate error messages. Find the light pattern below that matches the printer light pattern and follow the solutions to clear the error . T r oubleshooting Er r or Messages Printer Light P a tter ns Light status legend symbol for “light on” •[...]

P ROBLEM S OL VING 7. 23 T r oubleshooting Er r or Messages P aper is jammed inside the printer . • Clear the paper jam. See “Clearing P aper Jams” on page 7.7. Paper jam The printer ran out of memory in the middle of a print job. The page being printed may have been too complex for the memory capacity of the printer . Press the Cancel/Reprin[...]

P ROBLEM S OL VING 7. 24 Solving Print Quality Problems • R eset the printer by briefly turning the printer off and back on again. • If the error persists, contact the service representative. System error The size of the paper in the input tr ay is mismatched to the P aper Size setting in printer's properties. R emove the paper from the tr[...]

P ROBLEM S OL VING 7. 25 Common W indo ws Pr oblems Note: Refer to Microsoft Windows 9x, Me, NT 4.0 or 2000 documentation that came with your PC for further information on Windows error messages. Problem “File in Use” message appears during installation. “Error W riting to LPTx” message appears. “General Protection F ault” , “Exceptio[...]

P ROBLEM S OL VING 7. 26 Problem Y ou cannot use the computer while the printer is printing. Possible Cause and Solution Background Printing has not been selected. • F or LaserW riter 8.3, turn Background Printing on in the Chooser . Status messages will now be redirected to the Print Monitor allowing you to continue working while the computer is[...]

P ROBLEM S OL VING 7. 27 The following situations are PS language specific and may occur when sever al printer languages are being used. Note: T o receive a printed or screen displayed message when PS errors occur , open the Print Options dialog box and click the desired selection next to the PostScript errors section. Problem P ostScript file can [...]

This appendix provides information on the following topics: ◆ Printer Specifications ◆ P aper Specifications A A[...]

Printer Specifica tions Item Specification and Description Print Speed 16 PPM (A4), 17 PPM (Letter) R esolution 1200 dpi First Printing Time W armUp Time Less than 14 seconds P ower Consumption 300 W aver age during operation / Less than 20 W in power-sav e mode P ower Rating AC 100 ~ 127 V (USA, Canada) / 220 ~ 240 V (Others), 50 / 60 Hz Acoustic [...]

P aper Specifica tions This printer accepts a variety of media, such as cut -sheet paper (including up to 100 % recycled fiber content paper), envelopes, labels, tr ansparencies and custom-size paper . Properties such as weight, composition, grain and moisture content are important factors affecting printer performance and output quality . Paper th[...]

Tray 1 or Optional Tray 2 Letter Dimensions a 8.5 X 11 in. (216 X 279 mm) 16 to 28 lb Bond (60 to 105 g/m 2 ) 550 sheets of 20 lb Bond (75 g/m 2 ) paper Weight Capacity b A4 210 X 297 mm (8.3 X 11.7 in.) Executive Legal B5 (JIS) Folio 7.3 X 10.5 in. (191 X 267 mm) 8.5 X 14 in. (216 X 356 mm ) 182 X 257 mm (7.2 X 10 in.) 216 X 330 mm (8.5 X 13 in.) [...]

Paper Specifica tions F or best results, use conventional 90 g/m 2 (24 lb) paper . Make sure the paper is of good quality , and free of cuts, nicks, tears, spots, loose particles, dust, wrinkles, voids, and curled or bent edges. If you are unsure of what type of paper you are loading (such as bond or recycled), check the label on the package of the[...]

Paper Specifica tions Category Acid Content Specifications 5.5 ~ 8.0 pH Caliper .094 ~ .18 mm (3.0 ~ 7.0 mils) Curl in Ream Cut Edge Conditions Fusing Compatibility Grain Flat within 5 mm (.02 in.) Cut with sharp blades with no visible fra y . Moisture Content 4 % ~ 6 % by weight Smoothness 100 ~ 250 Sheffield Must not scorch, melt, offset, or rele[...]

Ideally , the printer and paper storage environment should be at or near room temperature, and not too dry or humid. R emember that paper absorbs and loses moisture rapidly . Heat works with humidity to damage paper . Heat causes the moisture in paper to evapor ate, while cold causes it to condense on the sheets. Heating systems and air conditioner[...]

Envelope construction is critical. En velope fold lines can vary considerably , not only between manufacturers, but also within a box from the same manufacturer . Successful printing on envelopes depends upon the quality of the en velopes. When selecting envelopes, consider the following components: • Weight: The weight of the envelope paper shou[...]

Double side-seams construction has vertical seams at both ends of the envelope r ather than diagonal seams. This style may be more likely to wrinkle. Be sure the seam extends all the way to the corner of the envelope as illustr ated below . En v elopes with Double Side Seams Envelopes with a peel-off adhesiv e strip or with more than one flap that [...]

When selecting labels, consider the quality of each component: • Adhesives: The adhesive material should be stable at 200 °C (392 °F), the printer’s fusing temper ature. • Arrangement: Only use labels with no exposed backing between them. Labels can peel off sheets with spaces between the labels, causing serious jams. • Curl: Prior to pri[...]

If you hav e a USB (Universal Serial Bus) port enabled on your computer , and if your computer is running Windows 98, you can connect your ML -1650 series printer to the USB chain of devices. This appendix provides information on the following topics: ◆ Installing the Printer Software ◆ Frequently Asked Questions About USB B B[...]

If you hav e a USB (Universal Serial Bus) port enabled on your computer , and if your computer is running Windows 98, you can connect your ML -1650 series printer to the USB chain of devices. Note: Connecting the printer to the USB port of the computer requires a certified USB cable. Y ou will need to buy the USB 1.0 or 1.1 compliant cable. ➝ To [...]

5 Check Search for the best driver for your device and click Next . 6 Check CD-ROM drive and click Browse , then choose x:1650Eng (or the desired language code, see page D .2.) USB (where x is the drive letter for the CD-ROM drive). 7 Click Next . The USB driver will be installed. 8 F ollow the instructions on the screen to complete the installa[...]

1 From the Start menu, select Settings , then select Printers . 2 Select the ML-1650 Series PCL 6 printer icon in the Printers folder . 3 Select Properties from the File menu. 4 Click the Details tab. Select SSUSB: (ML-1650) in the Print to the following port box. Click OK . The setup is now completed. Installing the Printer Software 3. Set your PC[...]

F r equentl y Ask ed Questions About USB Q Q Q Q What is USB? How can I determine if my computer’s USB port is enabled? A A Universal Serial Bus (USB) makes it easy to connect devices to your computer without having to open your PC. USB uses a standard port and plug combination for connecting devices like printers, modems, scanners, and digital c[...]

Q Q Q Q Q Q Can other users on my USB chain print to my ML-1650 series printer? Y es. Windows 98 allows you to “share” your printer using software settings on your computer . After others on the USB chain have installed the printer softw are for your specific printer , they can print to your shared printer . After I install my printer, why isn?[...]

Y our printer supports Macintosh systems with a built-in USB interface or 10/100 Base- TX network interface card (option for ML -1650). When you print a file from Macintosh, you can use the PCL driver to support your printer’ s major printing features. Y ou can also use PostScript driv er by installing the PPD file. T opics included in this appen[...]

Macintosh Installa tion T o use your ML -1650 Series printer and its software with a Macintosh, your system should have: • One of the following Macintosh models: -Power Macintosh series (for network connection only) -Power Macintosh G3, G4 -iMac series -iBook series • USB interface or network interface (for network connection only) • For netw[...]

USB Connection Macintosh Installation Y ou can connect the printer to your Macintosh using the USB interface or network interface. USB cable is not provided in your printer . Purchase a certified USB 1.0 or 1.1 compliant cable. 1 T urn off the printer and computer . 2 Hold the USB cable so the icon faces up and connect it to your printer’ s USB c[...]

If you have a printer with 10/100Base- TX network interface card installed (standard for ML -1651N, option for ML -1650), you can connect to an Ethernet network. Use a Category 5 twisted pair cable with RJ-45 connectors for 10/100Base- T Ethernet. 1 Plug one end of the network cable into the twisted-pair connector on the back of the printer . 2 Con[...]

Macintosh Installation Installing Software f or Macintosh 1 T urn on your computer and printer . 2 Insert the CD-ROM which came with your printer into the CD- ROM drive. 3 Double-click Samsung ML-1650 on your Macintosh desktop. 4 Select the correct language, then click Continue . 5 The Samsung Laser Printer Installer opens. Select installation type[...]

If you want to use y our printer’s PCL driver on y our Macintosh computer , take the following steps: Using PCL Driv er 1 From the Apple menu, select Chooser . 2 From the left pane of the Chooser window , click SAMSUNG PCL . Then the Samsung PCL driver name will appear in the right pane of the Chooser window . 3 Click the Samsung PCL driver , and[...]

Choose Watermark if you want to add a w atermark to each page in your document to emphasize its purpose or indicate how it should be handled. For details on the watermark option, see page 5.21. Using PCL Driv er 3 Choose your paper size, orientation, paper type and other options and click OK . C. 6 U SING Y OUR P RINTER WITH A M ACINTOSH[...]

4 Now open the File menu and click Print . Y ou see the main printer settings dialog box. 5 Choose the number of copies and indicate which pages you want to print. F or advanced printing features, select the desired option. For details, see page C.8. Using PCL Driv er 6 Click Print when you are finished checking your settings. Select the desired op[...]

Using PCL Driv er The Page Setup dialog bo x contains five categories of page setup properties. Listed below is the name of each property . -Darkness/Quality -Layout -Color -Background Printing -P aper Source Figures below display each property in the P age Setup dialog box. Advanced Printing Dar kness/Quality Select print darkness. Select print re[...]

Using PCL Driv er Color Select grayscale mode. Bac kg round Printing " Grayscale " Black&White T urns background printing on or off . Select a priority for your print job in the queue of jobs waiting to print, by clicking one of the following: • Normal to print in the order the job is received. • Urgent to print before any Normal [...]

C. 10 If you want to use the PS driv er which were installed on your Macintosh computer , you must install the PPD file to access your printer features and allow the computer to communicate with your printer . PPD file installation method is different for USB connection and the network connection. Using PS Driv er 1 F ollow the instruction as descr[...]

1 F ollow the instruction as described on page C.4 to install the PPD file on your computer . 2 From the Apple menu, select Chooser . 3 Click LaserWriter 8 (the PostScript driver pro vided with your Macintosh). The name of your printer appears in the list. Select SEC000xxxxxxxxx from the printer box (where the xxxxxxxxx varies depending on each of [...]

While your printer is primarily a Windows printer , you can also print from a DOS software progr am using the Remote Control P anel utility provided in the ML -1650 series CD-ROM. T opics included in this Appendix are: ◆ About R emote Control Panel for DOS ◆ Installing the R emote Control Panel for DOS Users ◆ Selecting Print Settings D D[...]

About R emote Contr ol P anel f or DOS DOS users have access to many printer features through specific DOS printer drivers; however , many software manufactures do not develop printer drivers for their software programs. The Samsung ML -1650 series printer provides the DOS software control panel for improved printer control when DOS printer drivers[...]

Installing the R emote Contr ol P anel f or DOS User s The Remote Control P anel utility is provided on the printer software CD-ROM. If you do not hav e a CD-ROM drive, refer to Appendix G, “Installing Software from Diskette” for information on obtaining printer software on diskettes. To install the DOS Remote Control Panel: 1 Insert the printe[...]

To access the Remote Control Panel 1 Make sure that the R emote Control Panel is in y our path statement. Y ou can check your path by typing PATH and pressing Enter . If the Remote Control P anel directory is not in your path, you will hav e to change to the default directory C:DOSUTIL to start the program. 2 At the DOS prompt, type DOSRCP and pre[...]

Selecting Print Settings CONFIG • Power Save determines the length of time the printer waits after a job is printed before it goes to a reduced power state. If the printer is used frequently , select OFF which keeps the printer ready to print with the minimum warm-up time. This uses more electricity to keep the printer warm and ready to print. ?[...]

Selecting Print Settings TEST • Self Test prints the configuration sheet. A list of the user default settings, the installed options, and the amount of printer memory av ailable prints. • Demo Page prints the demonstration page. It shows the printer features and specifications. PCL • Typeface allows you to select the desired typeface. This se[...]

If you want to use the P ostScript driv er provided with your system CD-ROM or diskettes to print a document, use the information on this Appendix. T opics included in this Appendix are: ◆ Setting Y our Printer with PS Option ◆ Installing PPD Files ◆ Accessing the PS Printer Driver F eatures E E[...]

Setting Y our Printer with the PS Option If you want to use the P ostScript driver to print a document, your printer should hav e: • PS DIMM (Option) F or instructions on installing the printer options, see Appendix H, “Printer Options. ” Installing PPD Files PPDs, in combination with the PostScript driv er , access the printer features and a[...]

2 Insert the CD-ROM shipped with your printer into your CD-ROM drive. If the CD-ROM drive does not automatically run: Select Run from the Start menu, and type x:cdsetup.exe in the Open box (where x is the drive letter for the CD-ROM drive), then click OK . 3 When the opening screen appears, select the appropriate language. 4 Click Install the Sams[...]

Accessing the PS Printer Driv er F ea tur es Certain printer features are not av ailable in this PS driver . Refer to “Printer Driver F eatures” on page 2.14. The printer automatically switches between PS and PCL printer languages depending on the driver you hav e selected. Opening the Printer Proper ties W indow The properties window for the W[...]

If you work in a networked en vironment, the printer can be shared by other users on the network. ML -1651N printer are network printers and can be connected to the network via direct attachment to an external print server . This appendix provides information on the following topics: ◆ About sharing the Printer on a Network ◆ Setting Up a Local[...]

About Sharing the Printer on a Netw or k If you work in a networked en vironment, you can connect the ML -1650 series printer to your network. Locally Shar ed Y ou can connect the printer directly to a selected computer (called the “host computer”) on the network. The printer can then be shared by other users on the network through a Windows 9x[...]

Setting Up Host Computer 1 Start Windows. 2 From the Start menu, select Control Panel , and double- click on the Network icon. 3 Check the File and Print Sharing box, then click OK . Close the window . 4 Click Start and select Printers from Settings , then double-click your printer name. 5 Select Properties in the Printers menu. 6 Click the Sharing[...]

Setting Up a Netw or k-Connected Printer T o use ML -1650 series printer as a network printer , you must install an optional network card in your printer . See page H.4 for information on installing network card. If you have ML -1651N printer , you do not need to install the network card. The Samsung ML -1651N printer are shipped with the network c[...]

If you need to install the printer software on a system that does not have a CD-ROM drive, use the instruction on this appendix to create the software diskettes and install the printer software from the diskettes. This appendix provides information on the following topics: ◆ Making Installation Diskettes ◆ Installing Software from Diskettes G G[...]

Making Installa tion Disk ettes If you do not have a CD-ROM driv e but you have access to another computer with a CD-ROM drive, you can copy software installation files from your printer softw are CD- ROM onto floppy diskettes, and then use the diskettes instead of the CD-ROM to install the software. Y ou can make installation diskettes for PCL6 pr[...]

4 The Copy to Floppy dialog box appears. Select the desired components you want to copy to the diskette from the Select box. Y ou can select PCL6 Printer Driver , PostScript Printer Description file, USB P ort Driver and RCP . Select the floppy disk drive you will use to insert the diskette. 5 Click Copy all disk images . If you want to copy a port[...]

7 If you have more than one disk, insert the next disk and click Yes . Repeat this step for a third disk if necessary . 8 When copying to diskettes has been completed, click Close in the Copy to Floppy dialog box. Then click Exit in the SAMSUNG PRINTER SETUP dialog box. Installing Softw ar e fr om Disk ettes The instructions to install a PCL 6 prin[...]

Y our printer is a full-featured laser printer that has been optimized to meet most of your printing needs. R ecognizing that each user may have different requirements, howev er , Samsung makes sever al options av ailable to enhance the printer’s capabilities. This appendix provides information on the following topics: ◆ Precautions ◆ Memory [...]

Pr ecautions DISCONNECT THE POWER CORD: Never remove the printer control board while the printer is plugged in. T o avoid the possibility of electrical shock, alw ays disconnect the power cord when installing or removing ANY internal or external printer option. DISCHARGE STATIC ELECTRICITY: The control board and internal printer options (Memory DIM[...]

Memor y and P ostScript DIMMs Additional printer memory and the PostScript option are pro vided on DIMMs (dual in-line memory modules). This procedure is applicable to either option. 1 T urn the printer power off and unplug all cables from the printer . 2 R emove the two screws on the rear of the printer , then remove the control board cover . 3 Lo[...]

5 Hold the memory DIMM so that the notch and the connection point are aligned with the slot as shown, and insert the DIMM all the way into the lower slot labeled FLASH-ROM MODULE at a 90 (Straight) degrees angle. Memor y and P ostScript DIMMs 1 2 1 2 4 Hold the PS DIMM so that the notch and the connection point are aligned with the slot as shown, a[...]

Netw or k Interf ace Car d R eview the precautions on page H.1 and then follow this procedure to install the Network card option in your printer . 1 Unpack the network printer card. Y ou should find the following items. 2 T urn the printer power off and unplug all cables from the printer . 3 R emove the two screws on the back of the printer , then [...]

6 Tighten the two screws as shown. 7 Tighten the two screws, then replace the plate. 8 R econnect the power cord and printer cable, then turn the printer on. Network Interface Car d Note: For information on configuring and using the printer on a network environment, refer to the documentation provided with the network card option. H. 5 P RINTER O P[...]

P aper T r ay 2 Y ou can increase the paper handling capacity of your printer by installing the optional T ray 2. The optional paper tr ay consists of two components; the support unit and paper tray . 1 T urn off the printer and unplug all cables from the printer . 2 Observe the location of the support unit’ s connector and tabs. 3 Align the prin[...]

Paper T r ay 2 Note: T o print from T ray 2, you must configure the printer driver from your application prior to printing. T o access the printer driver , see page 5.2. 5 R econnect the cables, then turn the printer on. Click. If this box is checked, you can select T ray 2 in the Paper Source drop-down list. H. 7 P RINTER O PTIONS[...]

Y ou can use Samsung ML -1650 Series printer in Linux environment. This appendix provides information on the following topic: ◆ Linux Driver Installation I I[...]

Linux Driv er Installa tion This Linux driver is designed for the Samsung ML -1650 Series printer and supports Linux Red Hat 6.0 or higher and Intel Linux. If your Linux version is not included, this driver might not work properly . • Install Setup Script file configuration a. /cdrom/linux/install.sh b. /cdrom/linux/ssprt.db c. /cdrom/linux/readm[...]

Linux Driv er Installation 3. Set up the printer filter . T o set up: 1 Run printtool at x terminal. 2 T o add the printer driver , click the Add button. 3 In the Add a Printer Entry window , decide the printer type you will use. Select Local Printer if you hav e a PC - connected printer . 4 Click the OK button. 5 If the Info button appears, ignore[...]

INDEX Numeric 2-sided printing 5.7 B booklet printing 5.11 C cancel, print job 5.5 Cancel/R eprint button 3.2 card stock, print 4.17 clean, printer 6.4 clean sheet, print 7.6 components 1.4 configuration page, print 7.6 control panel buttons 3.1 lights 3.4 custom-sized media, print 4.17 D Data light 3.4 Demo button 3.3 demo page, print 2.9, 7.6 dis[...]

INDEX J jam see paper jam L labels, print 4.14 letterhead, print 4.16 load, paper in the multi-purpose tray 4.8 in tra y 1 or the optional tray 2 2.5 using the manual feed 4.10 Linux driver I.1 M Macintosh connecting network interface C.3 connecting USB interface C.2 install PCL driver C.4 install PPD file C.10 solving common problems 7. 1 6 system[...]

INDEX P (continued) paper level indicator 4.6 P aper light 3.5 paper orientation, setting 5.3 paper out, indicator 7.22 paper source, setting 5.3 paper tra y change paper size in tray 2.6 load paper 2.5 optional T ray 2 H.6 paper type, setting 5.3 parallel, connection 2.8 PCL 6 driver see driver, PCL 6 poster , print 5.16 postscript 3 emulation 1.2[...]

R R eady Mode 3.4 rear output tra y 4.4 remote control panel install D.2 use D.2 reprint, last page 3.2 resolution 5.19 S setup printer chapter 2 specifications paper A.2 printer A.1 SR T mode 5.19 system error 7.24 T toner cartridge cleaning sheet 6.5 install 2.3 life expectancy 6.1 recycle 6.1 redistribute toner 6.2 save toner 5.6, 6.1 storage 6.[...]