Samsung STP-102S инструкция обслуживания

Warning - U.S This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interface when the equipment is operated in a commercial environment. This equipment generates uses, and can radiate radio freq[...]

3 Chapter 1. Unpacking 1-1. Checking the contents of the Printer 1-2. Locating the Printer 1-3. Printer Part names 1-4. Operating Control Panel 4 4 4 5 6 Table of Contents Chapter 2. Connecting the cable 2-1. Connecting the AC adapter to your printer 7 7 Chapter 3. Installing the Paper Roll 10 Chapter 4. Setting the DIP Switching 11 2-2. Connecting[...]

1-3. Printer Part Names 5 (1) Cover top (2) Case top (3) Case bottom (4) Control panel (5) Roller (6) Power switch (7) Interface connector (male) (8) DC Jack (9) Interface connector (female) (10) Roll paper (11) Detector switch POWER ERROR FEED ON LINE (1) FEED ON LINE (4) (3) (2) (5) (10) (11) POWER ERROR Control Panel Rear View Rear View STP-102S[...]

7 Chapter 2. Connecting the Cable 2-1. Connecting the AC adapter to your printer When the printer is used, use te optional AC adapter, AP-1611-UV for your printer.  Using an incorrect power supply may cause fire or electrical.  When connecting or disconnecting the power supply from the printer, make sure th[...]

9 NOTE The printer must be turned off before installing the paper roll. Chapter 3. Installing the Paper Roll Use a paper roll that matches the specifications. 1. Open the printer cover and remove the used paper roll core if there is one. 2. Insert the paper roll as shown below. 3. Pull out the paper roll until the paper comes out from the top of th[...]

11 12 DIP switch functions BPS 2400 4800 9600 19200 38400 57600 115200 Level 1 2 3 4 5 6 7 D/W1 ON OFF OFF ON ON OFF ON D/W2 OFF ON OFF OFF ON ON ON S/W3 OFF OFF ON ON OFF ON ON Dip Switch No. 1 2 3 Function Density Handshaking Reserved Language Reserved ON OFF 5 6 7 8 4 Normal DTR/DSR - Korean - Dark Xon/Xoff - Engish - Chapter 4. S[...]

13 14 Chapter 6. Code Table The following pages show the character code tables. To find the character corresponding to a hexadecimal number, count across the top of the table for the For example, 4A=J. 1. Self-test printing 1) Starting the self test To start printing the self-test on a paper roll, hold down the PAPER FEED button and turn on the pri[...]

16 15 P C 850 : M u lt ili ngual PC 860 : Po r t ugues e[...]

17 18 P C 865 : N o r d ic P C 863 : Canadi an - F r enc h[...]

19 20 S pac e P age[...]

Chapter 7. Functions Commands The commands listed in the table below are available for control of the printer. Command HT LF ESC SP ESC ! ESC $ ESC % ESC & ESC * ESC - ESC 2 ESC 3 ESC ? ESC @ ESC D ESC E ESC J ESC R ESC S ESC V Horizontal tab Print and line feed Set right-side character spacing Select print mode(s) Set absolute print position S[...]

23 24 HT [Name] [Format] [Description] Command Notation Horizontal tab. ASCII Hex Decimal Moves the print position to the next horizontal tab position. [Name] [Format] [Range] [Description] The name of the command. the code sequence. ASCII indicates the ASSCII equivalents. Hex indicates the hexadecimal equivalents. Decimal indicates the decimal equ[...]

Select bit-image mode. ASCII Hex Decimal m = 0, 1, 32, 33 0 < nL < 255 0 < nH < 3 0 < d < 255 Selects a bit-image mode using m for the number of dots specified by nL and nH, as follows. Number of data(k) = (nL + nH x 256) x 3 The nL and nH indicate the number of dots of the bit image in the horizontal direction. The number of dots[...]

27 28 n n n ESC 1B 27 J 4A 74 ESC J n [Name] [Format] [Range] [Description] Print and feed paper. ASCII Hex Decimal 0 < n < 255 Prints the data in the print buffer and feeds the paper n dots. n n n R 52 82 ESC 1B 27 ESC R n [Name] [Format] [Range] [Description] Select an international character set. ASCII Hex Decimal 0 < n < 10 Selects [...]

29 ESC c 5 n [Name] [Format] [Range] [Description] [Notes] Enable/Disable panel buttons. ASCII Hex Decimal 0 < n < 255 Enables or disables the panel buttons. When the LSB is 0, the panel buttons are enabled. When the LSB is 1, the panel buttons are disabled. ESC 1B 27 c 63 99 5 35 53 n n n ESC d n [Name] [Format] [Range] [Description] Print a[...]

31 32 GS L nL nH [Name] [Format] [Range] [Description] [Notes] Set left margin. ASCII Hex Decimal 0 < nL < 255 0 < nH < 255 Sets the left margin using nL and nH in standard mode. The left margin is set to (nL + nH x 256) dots from the beginning of the line. This command is effective only at the beginning of a line. Printable area Printi[...]

33 34 h 68 104 n n n GS h n [Name] [Format] [Range] [Description] Set bar code height. ASCII Hex Decimal 1 < n < 255 Set the height of the bar code. n specifies the number of dots in the vertical direction. GS 1D 29 Print bar code. ASCII Hex Decimal ASCII Hex Decimal 0 < m < 6 (k and d depends on the bar code system used.) 65 < m <[...]

35 APPENDIX B: Specification JF01-000012 Printing method Dot density Printing width Paper width Characters per line Printing speed Receive buffer size Supply voltage Environmental conditions MCBF Thermal line printing 200 x 200 Dpi (8 dot/mm) 48mm 58mm 42 (Font A)(12x24) ,56(Font B)(9x24) Approximately 1.97 inchs/sec 50 mm/sec at 25°C/printing dut[...]