Sanyo VCC-4374 инструкция обслуживания

INSTRUCTION MANUAL VCC-4374 COLOR CCD CAMERA About this manual B efo re in st a ll in g a nd us in g th e ca m e ra, pl ea se re ad th is ma nu al carefully. Be sure to keep it handy for later reference. L53U 4/ U S G B 19 99 , 1 0, 14[...]

SANYO INDUSTRIAL VIDEO COLOR VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s expense, unless specifically stated otherwise in this warranty . The names and addresses of Authorized Sanyo Service Centers may be obtaine[...]

Depending on the conditions of use, installation and environment, please be sure to make the appropriate settings and adjustments. If you need help with installation and/or settings, please consult your dealer. CONTENTS INFORMATION TO USER ....................................................................... 2 PRECAUTIONS ........................[...]

INFORMATION TO USER Safety Guard THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT. WARNING: TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK , DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. This installation should be made by a qualified service person and should conform [...]

PRECAUTIONS In case of problem Do not use the camera if smoke or a strange odour comes from the unit, or if it seems not to function correctly. Disconnect the power cord immediately, and consult your dealer (or a Sanyo Authorized Service Centre). Do not open or modify Do not open the cabinet, as it may be dangerous and cause damage to the unit. For[...]

PARTS NAMES 1 Power indicator (POWER) Comes on when the power to the camera is on. 2 Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. 3 Manual color/black and white setting terminal (CONTROL) • G (ground) terminal • C (color) terminal • B (black and white) term[...]

PARTS NAMES 8 Flange-back lock screw 9 Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). F Flange-back adjustment lever (See page 7) G Camera installation bracket The bracket can be fixed at the top or bottom of the camera. When fixing the bracket, be sure to[...]

CONCERNING AUTO-IRIS LENSES DC type auto-iris lens A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens is referred to as DC type coil lens or DC type non-amplifier lens. (Set the A.I. LENS switch to the DC position.) VIDEO type auto-iris lens A lens with amplifier circuit that operates on video si[...]

FLANGE-BACK ADJUSTMENT If the pick-up surface is not correctly positioned with relation to the lens focal point, the pictur e will be out of focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the flange-back position as described below. 1 Using a + screwdriver, loosen the flange-back lock scre[...]

MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). Checking the lens mount Do not use a lens if length “ L ” is more than 5 mm. If not, that may damage the camera and prevent proper installation. 1 Remove the lens mount cap from the camera. 2 Install the auto-iris lens. CS mount type lens Carefully align the lens mount wit[...]

MOUNTING THE LENS Rewiring the lens cable in the lens iris plug 1 Prepare the lens cable. Cut the c able at the plug, then rem ove approx. 8 mm of t he cab le she ath a nd str ip abou t 2 mm fro m each wire. 2 Install the lens iris plug. Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close[...]

CONNECTIONS Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc.) and cables are sold separately. 1 Make the video signal connection between the camera and the monitor or time lapse VCR. 2 Connect to 24 V AC UL listed class 2 power supply. CAUTION: • To prevent camera and/or power supply failure, pay close[...]

SETTINGS Camera setup section Control name Position a Color and Black/White level switch (C-BW) L b SYNC switch (SYNC) INT c Red and Blue color adjustment volume (R, B) about centre d White balance switch (WB) A e Electronic iris (EI)/Backlight compensation (BLC) switch OFF f Auto-iris lens switch (A.I. LENS) DC g Lens iris level volume (LEVEL) abo[...]

SETTINGS White balance adjustment Normally the WB (white balance) switch is set to the A (automatic) position and the white balance is adjusted automatically. If a manual white balance adjustment is necessary, follow the steps below. Set the WB switch to the M (manual) position, then adjust the color. • Turn R (VR303) to set the red ratio and/or [...]

SETTINGS Electronic iris function setting Use a manual or fixed iris lens and set the lens aperture to the shortest F stop. Set the EI/BLC switch to the EI-ON position. Note: Please refer to the specifications for dynamic range of the electronic iris. CAUTION: • The electronic iris is suitable for normal indoor use. When the EI/BLC switch is set [...]

SETTINGS C • B/W (color/black and white) switch setting This switch lets you select the timing of the automatic switching of the optical filter to color image or black and white image, according to the subject brightness. The default setting is “ L ”. Set the switch according to the brightness. (Fig. 2) H : for a brighter setting than L L : S[...]

TROUBLESHOOTING Bef ore taking t he ca mera for r epai rs, plea se chec k be low to make sure tha t th e ca mera is u sed co rrec tly. If it st ill d oes not p erform cor re ctly , ple ase con sult y o ur d eale r or a Sanyo A uthor ized Servi ce C entre . No picture on the monitor screen • Is the power turne d on to al l con nected devi ces? Is [...]

SPECIFICATIONS Camera: Scanning system : NTSC standard TV system (525 TV lines, 30 frames/sec.) Interlace : PLL 2:1 interlace Image device : 1/3 inch solid state image device CCD Picture elements : 811 (H) x 508 (V) Effective picture elements : 768 (H) x 494 (V) Synchronizing system : Internal sync, Line lock manually switchable Resolution : 470 TV[...]

SPECIFICATIONS Dimensions: mm Features and specifications are subject to change without prior notice or obligations. 136 126.5 1 15.4 25.2 11 1/4 ”– 20 UNC 67 54 28 3 L53U4/ US GB 1999, 10, 14 English 17[...]