Scag Power Equipment 37621220 инструкция обслуживания

OPERA T OR’S MANU AL GRASS COLLECTION SY STEM DESIGNED FOR: ASSEMBL Y OPER A TION MAINTENANCE MODEL# 37621219 & 37621220 SC A G TURF TIGER SERIES MOWER P PEC O PEC O P P P P PEC O PEC O PEC O MANU AL P ART#: Q0344 $4.00 REV : 1[...]

2 PECO GRASS COLLECTION SY STEM T ABLE OF CONTENTS SECTION P AGE Safety ------------------------------2 Safety Alert Symbols ----------------------3 W arranty -----------------------------4 I INTRODUCTION AND DESCRIPTION - - ------------5 1-1 Introduction - ------------------------5 1-2 Description - ------------------------5 II INST ALLA TION FOR [...]

3 SAFETY WARNING! WARNING! WARNING! WARNING! Saf ety Aler t Symbol Saf ety Signs NEVER ONL Y AFTER ST OPPING THE MOWER’S ENGINE AND WAITING FOR ALL MO VING P ARTS T O COME T O A COMPLETE ST OP . ALWA Y S UP DOWN NEVER NEVER “ A TTENTION! BECOME ALERT! Y OUR SAFETY IS INV OL VED!” D ANGER, WARNING, CA UTION operate the unit unless the discharg[...]

4 PECO LIMITED WARRANTY FOR NEW PR ODUCTS A. WHA T IS WARRANTED? 1. PRODUCT WARRANTY : ALL DEFECTIVE P ARTS MUST BE RETURNED T O PECO FOR INSPECTION TO DETERMINE V ALIDITY OF WARRANTY CLAIMS. 2. P ARTS REPLACED DURING WARRANTY : B. SECURING WARRANTY ADJUSTMENTS. C. ITEMS NOT CO VERED BY PECO WARRANTY . D. UN APPRO VED AL TERA TION OR MODIFICA TION.[...]

5 SECTION I INTR ODUCTION AND DESCRIPTION 1-1 Introduction 1-2 Description We are pleased to have you as a PECO customer . Y our collection system has been designed to give you a low maintenance, simple, and effective way to collect the grass clippings from your mower . This manual is provided to give you the necessary instructions to properly moun[...]

6 2-5 Dump Mechanism Adjustment 2-6 Exhaust Div er ter installation The linkage may be adjusted in two places, at the adjusting screw P#(K1435) and the latch assembly items. See page 7 for visual clarification. T o change the door closure tightness, screw the adjusting screw in or out. T o adjust the latch, change the length of the latch rod by scr[...]

Lift Handle Assembly Aluminum Grass Container W ith Handle Attached Latc h Hook Mechanism Assembly Aluminum Grass Container Assembl y 7[...]

8 Aluminum Grass Container Exploded View (1) C0025 Box T op (1) B81 13 Screen (4) B1668 Inlet Clamp (1) V1054 Inlet (1) A0273 Box Handle (1) J0522 Handle Grip (1) J0176 Latch Spring (2) B2526 Linkage Rod (2) K1422 Adjusting Nut (1) A0260 Latch Rod (2) K1435 Adjusting Screw (1) K1442 Adjusting Ball Joint (1)C0024 Box Bottom (1) B1529 Latch Hook (1) [...]

9 (1) E0012 BOO T (1) E6009 8” BLO WER CONE (1) ENGINE/ BLO WER/ BLADE ASSY . (1) HB0251 HARDWARE BAG (1) 6” x 39” UPPER HOSE (1) 8” x 44” LO WER HOSE (1) V1054 6” PLASTIC INLET (1) A0794 12 CU . FT . BO X ASSY . (2) J6006 7” - 8” HOSE CLAMPS (1) B2220 WEIGHT (2) B0026 WEIGHT BRACKET (1) A0923 MAIN FRAME ASSY . (1) A0294 LONG THR OT[...]

2-9 Engine/Blow er/Blade Assembl y Installation Place the engine/blower/blade assembly onto the engine mount arm assembly (Figure 2-9). Secure the engine/blower/blade assembly to the engine mount arm assembly by using (4) 5/16"-18 x 1-1/2" hex bolts P#(K1 157) and (4) 5/16"-18 flange nuts P#(K1 178). T o mount the boot plate P#(B0309[...]

11 2-11 Blow er Cone Installation Thread (1) 5/16”-18 jam nut P#(K0120) onto each end of (2) 5/16”-18 x 2-1/2” HHCS P#(K0125). Now partially thread the bolts into each of the two tabs located on the blower housing. Place blower cone so the two tabs line up with the bolts then tighten completely . See Figure 2-1 1. 2-12 Impeller Blade R emo va[...]

2-16 Low er Hose T o Boot Installation T ake the unattached end of the lower hose and slide it over the circular end of the boot. Use the lower hose clamp to secure the hose to the boot (Figure 2-16). T ip: Before securing clamp rotate hose counter-clockwise (away from yourself) approximately 1” to add in retaining boot to mower deck. 2-17 F ront[...]

13 2-18 T hrottle Cable Installation T o install the throttle cable kit to the box assembly , align the large end of the slot in the throttle base plate (Figure 2-18a) with the rivets located on the front of the box assembly frame (Figure 2-18b). Place the throttle base plate over the rivets, Slide the throttle cable kit to the right, moving the sm[...]

SECTION III OPERA TING INSTR UCTIONS 3-1 General Safety 3-2 Operation & Tips On Mo wing Only qualified people familiar with this operator ’s manual and the mower ’s operator’s manual should operate this machine. A. Perform BEFORE EACH USE maintenance list in paragraph 4-1. B. Start the engine/blower/blade assembly . B. Start mower . C. Wi[...]

15 Model Number Serial Number PECO OUTDOOR POWER EQUIPMENT Arden, Nor th Car olina 28704 WRITE THE MODEL AND SERIAL NUMBER IN THE BOX ABOVE FOR FUTURE REFERENCE. Unit Model Number :_________________________________ Unit Engine Size: __________________________________ Unit Serial Number : _______________________________ Date of purchase: _____/_____[...]

SAFETY DECALS T o promote safe operation, PECO supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. Part #: R1054 Part #: R1049 Part #: R1057 Part #: R1053 Part #: R1055 Part #:R1051 16 Part #: R1070 Part #: R1[...]

17[...]

P .O. BO X 1197 ARDEN, NORTH CAR OLINA 28704 (800) 438-5823 OR (828) 684-1234 F AX: (828) 684-0858 EMAIL: peco@lawn vac.com WEBSITE: www .lawn vac.com P PEC O PEC O P P P P PEC O PEC O PEC O[...]