Sears 661.62463 инструкция обслуживания

MODEL NO 661.623920 661.624420 661.624530 661.624630 661.624670 AND !iiiiii!ii_ili_: _! Kenmore CONV TIBLE DOWNIFRONT OUTLET EVAPORATIVE AmR COOLER o Installation o Operation e Repair Parts SEARS. ROEBUCK AND CO., Chicago. 1L 60684 U.S.A. 30780-6[...]

CONTENTS INSTALLATION Tools and Supplies You Need ................ 3 Safety Rules ............ 3 Data ................................... 3 Locating Your Cooler ...................... 4 Converting to Side Outlet ................... 5 Mounting Cooler-, ............ 6 Electrical Connections .......................... 7 Final Assembly and Adjustment .[...]

BNSTALLATgON TOOLS AND SUPPLIES YOU WiLL NEED • Pliers o Screwdrivers o Adjustable Wrenches o Tubing Cutter e 5/32 Hex Key Wrench e Electric Drill o Drill Bits o Hammer o Duct Caulking e 10 Sheet Metal Screws o Wiring Supplies, as Required by Local Electrical Code e Level e Duct, As Required (a local sheetmetal shopcan supply ducting) o Equipment[...]

INSTALLATHON LOCATING YOUR COOLER Your cooler has been shipped ready for installa- tion in a down discharge position. It can easily be changed to side discharge, The cooler must be securely fastened to a frame or pad mounL A roof kit is available from Sears° A duct must be attached to the cooler outlet° The duct must be the same size as the coole[...]

aNSTALLATnON YOU MAY WANT TO CONVERT YOUR COOLER TO SIDE DISCHARGE (Figure 3) H.n CONVERTING COOLER TO SiDE AIR SIDE OUTLET ,_ DISCHARGE (F|G.4) DOWN OUTLET O Remove both louvers and set them where they will not fall See pg_ 11, "Taking Off Louver" Q Remove four grille clips on side opposite motor (_ Remove a reservoir by pushing the wate[...]

INSTALLATRON LIFTING COOLER CAUTION: DO NOT LIFT ON THE LOUVERS, REMOVE THE LOUVERS BEFORE LIFTING, DO NOT LIFT ON THE CENTER OF THE CABINET FLANGES MOUNTING COOLER (Fig. 7) 1o Prepare duct to fit model used,, See outtet size specifications on page 3. 2. Cut opening in roof or wall to fit duct opening on cooler and box in opening= 3. Install duct a[...]

INSTALLATION ELECTRICAL CONNECTIONS The wiring must comply with local code& If you are not familiar with the codes or wiring practi- ces, get professional help. Use only a Sears 32-6251 wall mounted switch.. This new cooler does not require prewetting the pads before starting cooling and does not have a pump Existing switches with "pump on[...]

iNSTALLATiON FINAL ASSEMBLY AND ADJUSTMENT PUT FLOAT VALVE IN COOLER Put the float valve through the spout hole and cabinet hole Tighten the ring nut Be sure the float moves straight up and down. TURN THE FLOAT UNTIL A NARROW SIDE IS UP. Snap the Sp(ash Guard Cover into the Water Spout as shown The Water Spout and Splash Guard Cover are provided to[...]

IINSTALLATION MOTOR PULLEY ADJUSTMENT (Figure 13) NOTE: ALL DUCT CONNECTED COOLERS MUST BE ADJUSTED Long or small air ducts have excessive air resistance which decreases air output and motor amperage, You may compensate for this by adjusting the motor pulley. Use-a clamptype ammeter to check the motor amperage 1o Check amperage at the white lead in[...]

HOW TO USE YOUR COOLER HOW YOUR COOLER WORKS Your cooler evaporates water to cool air. Evaporative air cooling is the same natural cooling that happens when a breezesprings up after a summer shower, You feel cool because the rain water evaporates and carries away heat Your new cooler has a motor' (1) driven blower (2) which draws outside air t[...]

CARE OF YOUR COOLER CAUTION: ALWAYS UNPLUG YOUR COOLER BEFORE YOU WORK ON IT YOU COULD BE HURT IFTHE COOLER IS TURNED ON WHEN YOUR HANDS ARE tNS_DE THE COOLER SPRING CARE: Clean your cooler (See page 12) Oil your cooler (See page 13) Put a new pad in if the old pad is plugged with dirt or water hardness, (See pages 12 and 13). Check belt tightness [...]

CARE OF YOUR COOLER TAKING OFF PAD (Fig. 19) 1. Lift up the small roller ends to unsnap the two center rollers Pull out the two small rollers 2. Pull out and turn the top roller bearing arm to line up the slot 3+ Lift edge of pad from under the guide and pull out the top roll end, 4, Take out the pad and bottom roller which will slide out of the bo[...]

CARE OF YOUR COOLER PUTTING ON NEW PAD (Fig. 21) PADS NEED NO PREWETTING THE __. Put the lower roller in pad. Fit the lower roller into the botton slots in the frame Push the top roller through the pad, Fit the roll end over the pad motor shaft drive block _. Push the top roller end into the bearing Q Turn the bearing arm to hold the rolter_ TUCK T[...]

REPAUR PARTS KENMORE CONVERTIBLE DOWN/FRONT OUTLET EVAPORATIVE AIR COOLER. MODEL. NOS. 661.623920, 661.624420, 661.624530, 661.624630, 661.624670 4O 38 25 35 60_ 23 23 19 ' 1:: 1 47 ( 3O 34 48 50 56 49 _ / 55 56 55 54 10 53 17 28 26 25 14[...]

REPAaR PARTS KENMORE CONVERTIBLE DOWN/FRONT OUTLET EVAPORATIVE AIR COOLER MODEL NOS. 661.623920, 661.624420 661-624530,661.624630, 661.624670 NOTICE: Order by PART NUMBER, not by Key Number Refer to the back cover of this manual for parts ordering information KEY NO 1 2 3 4 5 6 PART NUMBERS 661.623920 i 30439 50255 STD523!07 32-61074 30315 STD50310[...]

KENtVtORE CONVERTIBLE DOWN/FRONT OUTLET EVAPORATIVE AIR COOLER MODEL NOS. 661.623920, 661.624420 661-624530,661 °624630, 661.624670 No= 661,623920 44 501243 45 30433 47 30878 48 30214-01 49 31047 50 30206=01 51 30224-01 52 30211 53 30212 54 32-6293 55 30465 56 30233-01 57 V30336 58 29862 59 STD601103 " 30780-6 60 ! 30338 61 24971=1 62 523122 [...]