Shiro SK9151 инструкция обслуживания

• User Manual • SK9151 Digital Enhanced Cordless Communication SKYPE™ DECT TELEPHONE[...]

1 Contents Introduction ............. ................ ............ ................ ................ ....... 1 Physical Details ............... ............. ................ ............... ............. .... 2 What the symbols mean .................... ................ ................ ............. 4 Setting up your telephone ................. [...]

2 Minimum System Requirements  Broadband Inte rnet Service  PC with the following minimum specifications: Pentium 400Mhz or above Windows® 2000® or XP® Available USB Port, USB2.0 or U SB1.1 Skype® version 1.2 o r higher (visit www.skype.com ) 128Mb RAM, 256Mb RAM recommended 10Mb Hard Disk spa ce CD RO M for Soft ware Drive r Package Cont[...]

3 Press this to make the handset ring, if you cannot remember where you put it, pres s it again to stop the handset ringing. Handset Locator Button Press to end a telephone call. Press and hold 2-3 seconds to switch th e handset on/off. INT K e y Press to make a n intercom call (if you have more than one handset). Pause Ke y Long press for p ause, [...]

4 What the symbols mean Batteries Charge Level Whenever this show s ‘nearly empt y’ ( ), put the handset on the base unit to charge the batteries. While th e batteries are b eing charged, the level sho wn will keep changing. Mute Your handset's microphon e is muted. Signal Level Shows the signa l betwee n the handset and base unit, and dis[...]

5 Installation 1. Choose a suitable site for the base unit Make sure it is not near to another telephon e, nor to other electrical equipment. 4. Switch on mains power at the socket 5. Fit the batteries in the handset(s) 6. Connect the base unit to the telephone line 7. Plug in the USB dong le into PC USB port 8. Download the latest version of Skype[...]

6 9. Mount the CD-ROM and install the pr ogram with CD installat ion provided. The installation should run automa ticall y. If it doesn’t, begin th e ins tallation by opening th e CD file namely Setup or Skyp e Dect . Follow the on-screen instruction s to complete the installation. After a successful insta llation, you will find an ic on namely S[...]

7 Making and Answering Calls To Ma ke a n Or dinary Call 1. Enter the telephone number and press Call key to place call; 2. If you make a mistake, press Right key to delete incorrect digits, before you press Call key. To Answer an Ordinary Ca ll 1. When the handset a nd base unit ring, press the Ca ll key to answer call. 2. When the AUTO TALK is tu[...]

8 1. When you already engaged on an ongoin g ca ll, if another Skype call is receiv ed, press Right key to enter option menu; 2. Then press Scrolling button to select Hook up and pre ss Lef t key ; 3. Press Right key to enter option menu again; 4. Press Scrolling button to select Switch ; 5. Press Left key to tog gle the phone co nnection. (If you [...]

9 To Check Memory You can use this feature to see ho w many of yo ur Phone Book’s loca tions have been not use d. 1. In standby mod e, press Right key, enter Phonebo ok mode, the display shows the stored numbers; 2. Press Lef t key and Scrolli ng button to t he location memor y ; 3. Press Left key , the display shows “ n Free”. Call Lists You[...]

10 To Set External/Interna l Ringer Melody (1 - 9 melody ) 1. Select < Ringer Set > under Handse t Set mode; 2. Press Left key to confirm, then Scrolling button to the location ExternalRing / InternalRing ; 3. Press Left key and Scrolling button to c hoose the ring melody you want to set; 4. Then press Left key to confirm the choice . To Set [...]

11 4. Press Left key to con firm. To Set Base Melody ( 1-9 melody) 1. Select < Ringer Settin gs> under Base Se ttings mode ; 2. Select < Ringer Melody > under Ringer Settings; 3. Press Left key Scrolling butto n to set the melody you pref er; 4. Press Left key to con firm. To Set Flash Time You can change flash time to short or long. 1.[...]

12 1. Select < LCR > und er Base Settings mode; 2. Press Lef t key, and key in the PI N; 3. Press Left key, then key in the SHORT number that you want to replace the long number; 4. Press Left key to co nfirm, then key in the LONG number; 5. Press Left key to co nfirm. To C ha nge Ba se PIN 1. Select < PIN > under Base Settings mode; 2.[...]

13 To register a USB dongle 1. Press and hold the Han dset locator button on the base unit for a while, until you hear "beep" sound twice continuo usly; 2. Insert the USB dongle into your PC USB por t, the LED will be blink ing. 3. Us e a pa per c lip o r a pen ci l tip t o dep res s and hold the res et button of dongle for 2~3 seconds, t[...]

14 1. Select Sk yp e under menu mod e; 2. Select < Conta ct List > un der S kype mode; 3. Press Lef t key, then the di spla y shows the Skype o nline user list; 4. Press Scrolling button to select the record you wish to call; 5. Press Call key to place a Skype call. Quick Search : This function e nables you to speed search the list by inputti[...]

15 To Ma ke a S kype C onfer ence Cal l: 1. When you already engaged on an ongoing call, if another Skype call is received, press Right key to enter option menu; 2. Then press Scrolling button to select Hook up and pre ss Lef t key ; 3. Press Right key to enter option menu again; 4. Press Scrolling button to select Conference Call ; 5. Press Left k[...]

16 2. The ou tside call is pu t on hold. When the ca ll answers, yo u can spe ak to the user, then press the End key to hang up and transfer the call. Troubleshooting Always check first that: • You have followed the steps listed on pages to ins tall and set up yo ur SK9151. • All connects are firmly in serted in their socke ts. • Mains p ower[...]

17 Check the Batteries Level symbol on the displa y. If it is low, recharge the batteries. The Caller Display feature isn’t working. You need to subscribe to the Ca ller Display featu re from your service provider. The caller may have withheld their number, or th ey may be calling from a network that does not transmit the Caller ID (for exampl e,[...]