Siig CN-WR0312-S1 инструкция обслуживания

1 Wireless-N PCI Adapter Quick Installation Guide Introducing the Wireless-N PCI Adapter The Wireless-N PCI Adapter is designed to connect your desktop computer to your wireless network for fast internet access. Features and Benefits • Complies with 802.11n Draft 2.0, 802.11g and 802.11b standards • Supports QoS-WMM, WMM-PS • Supports 64/128-[...]

2 Package Contents • Wireless-N PCI Adapter • Driver CD • Quick Installation Guide Layout Figure 1: Layout WPS Button Press this button and hold for 3 seconds to start WPS function. When WPS is enabled, the Link and Tx/Rx LEDs will be steadily on. Link LED On: Link to a wireless access point Off: Not linked to any wireless access point Tx/Rx [...]

3 Safety Information In order to keep the safety of users and your properties, please follow the following safety instructions. 1. Shutdown the computer and remove the power cord of your computer when you want to install / remove the network card. If you’re not familiar about interface card installation, ask an experienced technician for help. 2.[...]

4 Hardware Installation General instructions for installing the card are provided below. Since the design of computer cases and motherboards vary, refer to your computer’s reference manual for further information, if needed. Static Electricity Discharge may permanently damage your system. Discharge any static electricity build up in your body by [...]

5 Driver Installation Windows 2000/XP/2003 Server 1. At the Found New Hardware Wizard , click Cancel . 2. Insert the driver CD, Click Start , Run . Type D:PCIsetup.exe , click OK . (Change D: to match your CD-ROM drive letter) 3. Choose I accept the terms of the license agreement , then click Next . 4. Choose Install driver and Ralink WLAN utilit[...]

6 Windows Vista™ 1. At the Found New Hardware window, click Cancel . 2. Insert the driver CD. Click Start , in the Start Search box, type D:PCIsetup.exe , press Enter . (Change the D: to match your CD-ROM drive letter) 3. Click Allow . 4. Choose I accept the terms of the license agreement , then click Next . 5. Choose Install driver and Ralink [...]

7 If you stopped config utility by Exit function, you will not be able to maintain the wireless link to the access point you wish to use. In this case, you can start config utility again by clicking Start, All Programs, Ralink Wireless , Ralink Wirelss Utility . Connecting to Wireless Access Point After the driver is correctly installed, it will tr[...]

8 Figure 3 2. Configuration utility will scan for all wireless access points automatically. Scan results will be displayed here, please check if the wireless access point with the SSID (the name of wireless access point) you preferred is shown in Figure 4 . If the wireless access point you wish to connect does not show here, please click Rescan to [...]

9 3. Click the wireless access point or network device you wish to connect to, then click Connect , shown in Figure 5 below. Figure 5 The non-encrypted access point (The Encryption field indicate None) will connected within one minute. Please jump to step 5 on page 9 if the access point you selected enables encryption, otherwise proceed to next ste[...]

10 If the wireless access point you selected have SSID, please skip this step, shown in Figure 6 . Figure 6 5. If the wireless access point uses encryption, you have to input WEP passphrase or WPA preshared key. Shown on Figure 7 , please ask the owner of the wireless access point to obtain the correct passphrase/preshared key and enter here, then [...]

11 6. You’ll see Connected <-> SSID (SSID is the SSID of the wireless access point or wireless device you connected to) message displayed at lower-left corner of configuration utility, congratulations, you’re successfully connected to the access point or wireless device you selected, shown in Figure 8 . Figure 8 SSID : The Service Set IDe[...]

12 Signal : Shows the signal strength of access point or wireless device. Larger number means better radio strength. Channel : Shows the channel number that access point or wireless device uses. Encryption : Shows the encryption method that access point or wireless device uses. If the wireless access point does not enable encryption, you’ll see N[...]

13 Using Windows Zero Configuration Windows XP and Vista has a built-in wireless network configuration utility called as Windows Zero Configuration (WZC). You can use WZC to configure your wireless network adapter. 1. Right-click Ralink configuration utility icon and select Use Zero Configuration as Configuration utility, shown in Figure 9. Figure [...]

14 Figure 10 5. All wireless access points in proximity will be displayed here. If the access point you want to use is not displayed here, please move your computer closer to the access point, or you can click Refresh network list to rescan access points. Click the access point you want to use if it’s shown, then click Connect, shown in Figure 11[...]

15 7. If you can see Connected message, the connection between your computer and wireless access point is successfully established. Soft-AP Function In addition to being a wireless client of other wireless access points, this wireless card can act as a wireless service provider. You can switch this wireless card’s operating mode to AP mode to sim[...]

16 After you select Switch to AP Mode , the Ralink utility icon will indicated the wireless card is operating in AP mode now. If you want to switch the wireless card back to station mode (become a client of other wireless access points), click Switch to Station Mode . Config Figure 13 SSID : Please input the SSID (the name used to identify this wir[...]

17 Channel : Please select the wireless channel you wish to use. The number of channels available here will vary depends on the setting of Country Region Code . Wireless Mode : Please select the wireless operating mode. You can limit the type of wireless client to 802.11b or 802.11g only, or allow 802.11b/g, and 802.11b/g/n clients. It’s safe to [...]

18 2 : SPAIN 3 : FRANCE 4 : MKK 5 : MKKI (TELEC) 6 : ISRAEL (Channel 3 to 9) 7 : ISRAEL (Channel 5 to 13) Beacon(ms) : You can define the time interval that a beacon signal should be send. Default value is 100. Do not modify this value unless you know what will be affected. Idle Time : Select the idle time of your wireless network card. Default val[...]

19 Security Settings This wireless card supports wireless encryption in AP mode, which will encrypt the data being transferred over the air to enhance data security level. It’s recommended to enable data encryption unless you wish to open your computer (and its internet connection) to the public. When you click Security Setting in Ralink configur[...]

20 Encryption Type : Please select an encryption mode. The available options in this setting item will vary depending on the authentication type you select. If you select Not Use , data will not be encrypted and people with some networking knowledge will be able to read the data you transfer with proper tool. Note : WPA encryption is safer than WEP[...]

21 If you want to use WEP 64 bit encryption, please input 10 characters; if you select HEX, or input 5 characters if you select ASCII; If you want to use WEP 128bit encryption, please input 26 characters if you select HEX, or input 13 characters if you select ASCII. 128 bit encryption is safer then 64 bit, but the data transfer speed will be slight[...]

22 Figure 15 Access Policy : Select the policy type of your access rule: Disable :Allow any wireless client with proper authentication settings to connect to this access point. Allow All : Only allow wireless clients with MAC address listed here to connect to this access point. Reject All: Reject wireless clients with MAC address listed here to be [...]

23 Mac Table Shows the list all wireless clients connected to this access point, shown in Figure 16. Figure 16 MAC Address : Displays the MAC address of this wireless client. AID : The serial number of this wireless connection. Power Saving Mode : Displays the capability of power saving function of this wireless client. Status : Displays additional[...]

24 Event Log This software access point will log all wireless-related activities as a log, shown in Figure 17 . Figure 17 You can click Clear to remove all entries in the log.[...]

25 Statistics This page shows detailed information about how your software access point works, shown in Figure 18 . Figure 18 You can click RESET COUNTERS button to reset all counters to zero.[...]

26 Blank Page[...]

27 Technical Support and Warranty QUESTIONS? SIIG ’ s Online Support has answers! Simply visit our web site at www.siig.com and click Support . Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and a technical support analyst[...]