Simplicity 1693754 инструкция обслуживания

OPERA T OR’S MANU AL Snow Plo w/Dozer Blade Mfg. No. Description 1693754 42” Angling Dozer Blade (Multiple Applications) Hitch Mfg. No. Description 1694147 Pivot Hitch (Prestige / 1800 / 2800 & Conquest / 1700 / 2700 Series) 42” Angling Sno w / Doz er Blade & Hitc h 1723445-02 Rev 11/2002 TP 100-2564-02-AT-SMA[...]

1 T able of Contents Adjustments .........................................................7 Skid Shoe Adjustment .....................................7 Spring T ension .................................................7 Lift Rod Adjustment .........................................8 Downw ard Pressure Adjustment .....................8 Initial Setup &[...]

OPERA TING SAFETY ● Always clear snow up and down the face of slopes, never across the face. Exercise extreme caution when changing direction on slopes. Do not attempt to clear steep slopes. ● Exercise extreme caution when operating on, or crossing, gravel drives, walks or roads. Stay alert for hidden hazards or traffic. ● After striking an o[...]

3 TRA CT OR CONTROLS Before you begin operating the tractor with the dozer blade attachment, make certain you have: • Read and understood the instructions in the tractor Operator’s Manual. • Become thoroughly familiar with all of the tractor controls and their operation, including how to safely and properly start and stop the unit. • Practi[...]

4 Checks Bef ore Star ting 1. Refer to the Maintenance & Adjustments sections of this manual and perform any needed service. Also, refer to the tractor Operator’s Manual and perform any required service. 2. Remove any objects from the work area which might interfere with plowing activity. 3. Adjust the skid shoes to desired height. See Skid S[...]

5 General Operating Instructions Daily Stora ge 1. Allow tractor engine to cool before storing in any enclosure. 2. After dozing or plowing jobs are completed, hose or brush down the blade to remove excess dirt. 3. Lightly oil all pivot points. Coat bare metal surfaces to prevent corrosion. IMPORT ANT NOTE Refer to Tractor Operator’s Manual for i[...]

6 Maintenance Schedule For Normal Care Care Required Schedule Clean debris from After each use. dozer blade. Lubricate dozer blade. Every 10 hours or at least once a year. Lubricate Dozer Blade Lubricate the dozer blade as shown in Figure 2. Where an oil can is shown, wipe the area clean, apply a few drops of oil (SAE 30), then wipe up drips or spi[...]

7 Adjustments Skid Shoe Adjustment Slotted holes are provided to permit adjustment of the shoe assemblies for raising and lowering the blade to various working heights (see Figure 3). When cleaning snow from gravel or earth drives or walks, the shoe assemblies should be lowered fully to prevent blade contact with gravel or ground. When cleaning smo[...]

8 Adjustments Figure 6. Adjusting Lift Rod A. Front Set Collar B. Rod Guide C. Spring D. Rear Set Collar E. Spring Clip Lift Rod Adjustment In the fully raised position the blade should be 4”-5” off the ground. In the fully lowered position, the lift rod should compress the spring creating downward pressure on the blade. LIFT HEIGHT ADJUSTMENT [...]

9 Initial Setup & Assembly 4 6 4 1 3 4 4 11 7 25 26 24 23 21 10 22 20 19 15 18 17 16 14 13 12 15 27 8 9 28 3 5 10 2 2 29 30 31 32 33 34 35 36 37 38 Figure 7. Dozer Blade and Pivot Hitch Ref Qty Description 1 1 ROD, Control Handle, Upper 2 6 NUT, Hex, 5/16-18 3 2 LOCKWASHER, 5/16 4 4 WASHER, 5/16 5 2 CAPSCREW, 5/16-18 x 1-1/4 6 1 ROD, Control Ha[...]

Figure 9. Install pivot hitch Assembly A. Safety Clip C. Long Hitch Pin B. Pivot Hitch D. Sub-Frame Hitch 10 Initial Setup & Assembly INITIAL SETUP & ASSEMBL Y Assemble Blade 1. See Figure 8. Insert threaded end of eyebolt (A) through lug on blade, and screw on 5/16 nut (B) just far enough so that it is flush with the end of the eye- bolt. [...]

11 Initial Setup & Assembly Install Lift Rod 1. Insert the end of the rod guide (A, Figure 11) through hole in upright of lift arm (B), and secure with spring clip (C). NOTE: The rod guide (A, Figure 11) should be installed in the lower hole for hydraulic lift applications. For manu- al lift applications, the rod guide may be installed in eithe[...]

12 Initial Setup & Assembly Figure 13. Control Rod Support A. Support B. Capscrew, 5/16-18 x 1 C. Washer & Nut D. Footrest Support (Frame) E. Foot Rest (Tunnel) F. Original Taptite Screw (Discard) Install Angling Control Rod NOTE: If installing dozer blade on the unit equipped with a snowcab, the angling rod support (A, Figure 14) is not re[...]

13 Removing & Attaching the Hitch & Blade REMO V AL & INST ALLA TION Removing & Attac hing Dozer Blade 1. Lower the blade. Position the lift so that it is not lifting the blade or applying downward pressure. 2. Remove the hair pin clip and washer (D, Figure 16) securing the angling control rod to the clevis. Disconnect the angling c[...]

14 Lift V ariations A F C D G Figure 17. Lift Link - Manual Lift Models A. Pin B. Rear Hole of Lift Bar (Snowthrower Applications) C. Spacer D. Hair Pin Clip E. Upper Hole (Snowthrower Applications) F. Slot of Lift Link (Mower Applications) G. Lower Hole (Mower Applications) A B C D E Snowthrower & Dozer Applications Mower Applications Figure 1[...]

15 Notes[...]

T orque Specification Chart FOR ST ANDARD MACHINE HARDWARE (T olerance ± 20%) Hardware Grade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.9 10-24 27 3.1 43 4.9 60 6.8 10-32 31 3.5 49 5.5 68 7.7 1/4-20 66 7.6 8 10.9 12 16.3 1/4-28 76 8.6 [...]

MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 2001 Simplicity Manufacturing, Inc. All Rights Reserved. Printed in USA.[...]